Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467922 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B009083  Left Frontal Restraints Sensor Value of Signal Protection Calculation Incorrect  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B009083 Left Frontal Restraints Sensor Value of Signal Protection Calculation Incorrect One of the following conditions is met:
·

A front airbag sensor LH malfunction.

·

An airbag ECU assembly malfunction.


·

Front Airbag Sensor LH

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

E465210E80
5.427,2.938 6.927,3.479 1.5,0.542 10 false Airbag ECU Assembly 5.417,2.76 5.875,2.927 0.458,0.167 10 false I24 5.292,0.792 5.75,1.094 0.458,0.302 10 false 30 5.302,1.99 6.052,2.365 0.75,0.375 10 false 31 5.615,0.875 6.073,1.177 0.458,0.302 10 false +SL 5.604,2.063 6.354,2.438 0.75,0.375 10 false -SL 1.729,0.802 2.188,1.104 0.458,0.302 10 false 2 1.729,1.948 2.188,2.25 0.458,0.302 10 false 1 1.323,0.917 1.781,1.219 0.458,0.302 10 false +SL 1.323,2.115 2.073,2.49 0.75,0.375 10 false -SL 0.292,2.781 0.646,2.958 0.354,0.177 10 false B31 0.292,2.958 1.969,3.25 1.677,0.292 10 false Front Airbag Sensor LH

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
DTC B009083 is output A
DTC B009083 is not output B


Post-procedure1

c.

None



A

2.CHECK CONNECTION OF CONNECTORS

B

2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


Procedure1

c.

Check that the connectors are properly connected to the airbag ECU assembly and front airbag sensor LH.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK FRONT AIRBAG SENSOR LH

NG

CONNECT CONNECTORS PROPERLY

3.CHECK FRONT AIRBAG SENSOR LH
a.
C413953C01
0.646,1.292 0.958,1.49 0.313,0.198 10 false *1 2.365,1.385 2.677,1.583 0.313,0.198 10 false *2 1.552,0.594 1.865,0.792 0.313,0.198 10 false *3
*1 Front Airbag Sensor RH
*2 Airbag ECU Assembly
*3 Wire Harness


Interchange the front airbag sensor LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

4.CHECK FRONT AIRBAG SENSOR LH
4.CHECK FRONT AIRBAG SENSOR LH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
DTC B009083 is output A
DTC B009583 is output B


Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


f.

Return the front airbag sensor RH and LH to their original positions and connect the connectors.



A

B