Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467922 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B009087  Left Frontal Restraints Sensor Missing Message  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B009087 Left Frontal Restraints Sensor Missing Message One of the following conditions is met:
·

The airbag ECU assembly detects a line short in the front airbag sensor LH circuit for 2 seconds.

·

The airbag ECU assembly detects a short to ground in the front airbag sensor LH circuit for 2 seconds.

·

The airbag ECU assembly detects a short to B+ in the front airbag sensor LH circuit for 2 seconds.

·

The airbag ECU assembly detects an open in the front airbag sensor LH circuit for 2 seconds.

·

A front airbag sensor LH malfunction.

·

An airbag ECU assembly malfunction.


·

Wire harness

·

Front airbag sensor LH

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

E465210E80
5.427,2.938 6.927,3.479 1.5,0.542 10 false Airbag ECU Assembly 5.417,2.76 5.875,2.927 0.458,0.167 10 false I24 5.292,0.792 5.75,1.094 0.458,0.302 10 false 30 5.302,1.99 6.052,2.365 0.75,0.375 10 false 31 5.615,0.875 6.073,1.177 0.458,0.302 10 false +SL 5.604,2.063 6.354,2.438 0.75,0.375 10 false -SL 1.729,0.802 2.188,1.104 0.458,0.302 10 false 2 1.729,1.948 2.188,2.25 0.458,0.302 10 false 1 1.323,0.917 1.781,1.219 0.458,0.302 10 false +SL 1.323,2.115 2.073,2.49 0.75,0.375 10 false -SL 0.292,2.781 0.646,2.958 0.354,0.177 10 false B31 0.292,2.958 1.969,3.25 1.677,0.292 10 false Front Airbag Sensor LH

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


Procedure1

c.

Check that the connectors are properly connected to the airbag ECU assembly and front airbag sensor LH.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS

Pre-procedure1

a.
C413952C01
0.542,1.458 0.854,1.656 0.313,0.198 10 false *1 2.719,1.563 3.031,1.76 0.313,0.198 10 false *2 1.635,0.792 1.865,0.948 0.229,0.156 10 false *3
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Disconnect the front airbag sensor LH connector.


Procedure1

c.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

d.

Turn the ignition switch off.



OK

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN THE CIRCUIT)

Pre-procedure1

E441548C07
1.26,3.667 1.677,3.917 0.417,0.25 0.375,0.844 0.792,1.094 0.417,0.25 1.771,4.448 2.021,4.448 2.021,4.448 2.115,4.073 true 2.625,4.448 2.375,4.448 2.375,4.448 2.208,4.073 true 0.854,1.469 1.104,1.469 1.104,1.469 1.24,0.979 true 1.938,1.469 1.688,1.469 1.688,1.469 1.458,0.979 true 0.417,2.615 0.604,2.781 0.188,0.167 10 false *1 0.708,2.115 0.896,2.281 0.188,0.167 10 false D 1.031,2.135 1.219,2.302 0.188,0.167 10 false C 2.063,2.125 2.25,2.292 0.188,0.167 10 false B 2.385,2.125 2.573,2.292 0.188,0.167 10 false A 2.854,2.719 3.042,2.885 0.188,0.167 10 false *2 0.469,0.885 0.771,1.042 0.302,0.156 10 false B31 0.25,0.25 0.438,0.417 0.188,0.167 10 false *a 0.573,1.396 1.083,1.573 0.51,0.177 10 false -SL 1.99,1.396 2.469,1.563 0.479,0.167 10 false +SL 1.531,4.396 1.865,4.583 0.333,0.188 10 false +SL 2.677,4.375 3.063,4.531 0.385,0.156 10 false -SL 1.354,3.708 1.677,3.885 0.323,0.177 10 false I24 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.49,2.302 1.719,2.458 0.229,0.156 10 false *3
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Airbag Sensor LH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


a.

None


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B31)Location & Routing

Click Connector(B31)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Front Airbag Sensor LH

B31-2 (+SL) - B31-1 (-SL) Always 1 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

Pre-procedure1

a.
E441549C06
0.375,0.833 0.792,1.083 0.417,0.25 1.25,3.75 1.667,4 0.417,0.25 0.833,1.5 1.083,1.5 1.083,1.5 1.25,0.958 true 1.917,1.5 1.667,1.5 1.667,1.5 1.469,0.969 true 1.5,3.5 1.667,3.5 1.667,3.5 2.083,4 true 3,3.208 2.75,3.208 2.75,3.208 2.167,4 true 1.656,4.406 1.99,4.406 true 0.417,2.615 0.604,2.781 0.188,0.167 10 false *1 1.021,2.135 1.208,2.302 0.188,0.167 10 false C 2.073,2.125 2.26,2.292 0.188,0.167 10 false B 2.385,2.125 2.573,2.292 0.188,0.167 10 false A 2.854,2.719 3.042,2.885 0.188,0.167 10 false *2 0.458,0.875 0.792,1.083 0.333,0.208 10 false B31 0.25,0.25 0.438,0.417 0.188,0.167 10 false *a 1.479,4.344 1.698,4.51 0.219,0.167 10 false *4 0.563,1.438 1.073,1.615 0.51,0.177 10 false -SL 1.958,1.427 2.438,1.594 0.479,0.167 10 false +SL 1.354,3.792 1.656,3.948 0.302,0.156 10 false I24 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.469,2.313 1.698,2.469 0.229,0.156 10 false *3 0.708,2.135 0.896,2.302 0.188,0.167 10 false D 1.229,3.427 1.708,3.594 0.479,0.167 10 false +SL 3.042,3.135 3.406,3.333 0.365,0.198 10 false -SL
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to Front Airbag Sensor LH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Using a service wire, connect terminals 30 (+SL) and 31 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B31)Location & Routing

Click Connector(B31)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Front Airbag Sensor LH

B31-2 (+SL) - B31-1 (-SL) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

Disconnect the service wire from connector B.



OK

5.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)

Pre-procedure1

E441548C07
1.26,3.667 1.677,3.917 0.417,0.25 0.375,0.844 0.792,1.094 0.417,0.25 1.771,4.448 2.021,4.448 2.021,4.448 2.115,4.073 true 2.625,4.448 2.375,4.448 2.375,4.448 2.208,4.073 true 0.854,1.469 1.104,1.469 1.104,1.469 1.24,0.979 true 1.938,1.469 1.688,1.469 1.688,1.469 1.458,0.979 true 0.417,2.615 0.604,2.781 0.188,0.167 10 false *1 0.708,2.115 0.896,2.281 0.188,0.167 10 false D 1.031,2.135 1.219,2.302 0.188,0.167 10 false C 2.063,2.125 2.25,2.292 0.188,0.167 10 false B 2.385,2.125 2.573,2.292 0.188,0.167 10 false A 2.854,2.719 3.042,2.885 0.188,0.167 10 false *2 0.469,0.885 0.771,1.042 0.302,0.156 10 false B31 0.25,0.25 0.438,0.417 0.188,0.167 10 false *a 0.573,1.396 1.083,1.573 0.51,0.177 10 false -SL 1.99,1.396 2.469,1.563 0.479,0.167 10 false +SL 1.531,4.396 1.865,4.583 0.333,0.188 10 false +SL 2.677,4.375 3.063,4.531 0.385,0.156 10 false -SL 1.354,3.708 1.677,3.885 0.323,0.177 10 false I24 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.49,2.302 1.719,2.458 0.229,0.156 10 false *3
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Airbag Sensor LH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


a.

None


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B31)Location & Routing

Click Connector(B31)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Front Airbag Sensor LH

B31-2 (+SL) - Body ground Always 1 MΩ or higher
B31-1 (-SL) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

6.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

Pre-procedure1

a.
E441548C07
1.26,3.667 1.677,3.917 0.417,0.25 0.375,0.844 0.792,1.094 0.417,0.25 1.771,4.448 2.021,4.448 2.021,4.448 2.115,4.073 true 2.625,4.448 2.375,4.448 2.375,4.448 2.208,4.073 true 0.854,1.469 1.104,1.469 1.104,1.469 1.24,0.979 true 1.938,1.469 1.688,1.469 1.688,1.469 1.458,0.979 true 0.417,2.615 0.604,2.781 0.188,0.167 10 false *1 0.708,2.115 0.896,2.281 0.188,0.167 10 false D 1.031,2.135 1.219,2.302 0.188,0.167 10 false C 2.063,2.125 2.25,2.292 0.188,0.167 10 false B 2.385,2.125 2.573,2.292 0.188,0.167 10 false A 2.854,2.719 3.042,2.885 0.188,0.167 10 false *2 0.469,0.885 0.771,1.042 0.302,0.156 10 false B31 0.25,0.25 0.438,0.417 0.188,0.167 10 false *a 0.573,1.396 1.083,1.573 0.51,0.177 10 false -SL 1.99,1.396 2.469,1.563 0.479,0.167 10 false +SL 1.531,4.396 1.865,4.583 0.333,0.188 10 false +SL 2.677,4.375 3.063,4.531 0.385,0.156 10 false -SL 1.354,3.708 1.677,3.885 0.323,0.177 10 false I24 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.49,2.302 1.719,2.458 0.229,0.156 10 false *3
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Airbag Sensor LH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B31)Location & Routing

Click Connector(B31)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Front Airbag Sensor LH

B31-2 (+SL) - Body ground Ignition switch ON Below 1 V
B31-1 (-SL) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.



OK

7.CHECK FRONT AIRBAG SENSOR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK FRONT AIRBAG SENSOR LH
a.
C413953C01
0.646,1.292 0.958,1.49 0.313,0.198 10 false *1 2.365,1.385 2.677,1.583 0.313,0.198 10 false *2 1.552,0.594 1.865,0.792 0.313,0.198 10 false *3
*1 Front Airbag Sensor RH
*2 Airbag ECU Assembly
*3 Wire Harness


Connect the I24 airbag ECU assembly.


b.

Interchange the front airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

8.CHECK FRONT AIRBAG SENSOR LH
8.CHECK FRONT AIRBAG SENSOR LH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B009087 is output A
DTC B009587 is output B
DTC B009087 and B009587 are not output C


HINT:

Codes other than DTCs B009087 and B009587 may be output at this time, but they are not related to this check.



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


f.

Return the front airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C