Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467922 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B009583  Right Frontal Restraints Sensor Value of Signal Protection Calculation Incorrect  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B009583 Right Frontal Restraints Sensor Value of Signal Protection Calculation Incorrect One of the following conditions is met:
·

A front airbag sensor RH malfunction.

·

An airbag ECU assembly malfunction.


·

Front airbag sensor RH

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

E465222E23
0.323,2.802 0.781,3 0.458,0.198 10 false B30 0.333,2.979 1.906,3.177 1.573,0.198 10 false Front Airbag Sensor RH 1.271,0.885 1.646,1.083 0.375,0.198 10 false +SR 1.26,2.052 1.635,2.25 0.375,0.198 10 false -SR 1.708,0.771 2.083,0.969 0.375,0.198 10 false 2 1.75,1.938 2.125,2.135 0.375,0.198 10 false 1 5.604,0.906 5.979,1.104 0.375,0.198 10 false +SR 5.625,2.063 6,2.26 0.375,0.198 10 false -SR 5.292,0.781 5.531,0.969 0.24,0.188 10 false 29 5.271,1.948 5.51,2.135 0.24,0.188 10 false 28 5.51,2.792 5.969,2.99 0.458,0.198 10 false I24 5.51,2.958 7.021,3.5 1.51,0.542 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B009583 is output A
DTC B009583 is not output B



Post-procedure1

c.

None



A

2.CHECK CONNECTION OF CONNECTORS

B

2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


Procedure1

c.

Check that the connectors are properly connected to the airbag ECU assembly and front airbag sensor RH.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK FRONT AIRBAG SENSOR RH

NG

CONNECT CONNECTORS PROPERLY

3.CHECK FRONT AIRBAG SENSOR RH
a.
C413953C01
0.646,1.292 0.958,1.49 0.313,0.198 10 false *1 2.365,1.385 2.677,1.583 0.313,0.198 10 false *2 1.552,0.594 1.865,0.792 0.313,0.198 10 false *3
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly
*3 Wire Harness


Interchange the front airbag sensor RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

4.CHECK FRONT AIRBAG SENSOR RH
4.CHECK FRONT AIRBAG SENSOR RH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B009583 is output A
DTC B009083 is output B



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


f.

Return the front airbag sensor LH and RH to their original positions and connect the connectors.



A

B