Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467925 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  P007015  Ambient Temperature Sensor Circuit Short to Battery or Open  


DESCRIPTION

The cooler thermistor (ambient temperature sensor) is installed in front of the cooler condenser assembly to detect the ambient temperature, which is used to control the air conditioning system. This sensor is connected to the air conditioning amplifier assembly and detects fluctuations in the ambient temperature. This data is used for controlling the cabin temperature. The sensor sends a signal to the air conditioning amplifier assembly. The resistance of the cooler thermistor (ambient temperature sensor) changes in accordance with the ambient temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the cooler thermistor (ambient temperature sensor) and reads voltage changes due to changes in the resistance of the cooler thermistor (ambient temperature sensor).

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
P007015 Ambient Temperature Sensor Circuit Short to Battery or Open Diagnosis Condition:

Ignition switch ON


Malfunction Status:

Open or short (+B) in ambient temperature sensor circuit


Detection Time:

Continuously for 4 seconds or more


·

Cooler thermistor (ambient temperature sensor)

·

Harness or connector

·

Air conditioning amplifier assembly


Memorized Air Conditioner A

DTC Detection Condition Combination Table
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Ignition switch ON ○ ○
Malfunction Status Open in ambient temperature sensor circuit ○ -
Short (+B) in ambient temperature sensor circuit - ○
Detection Time Continuously for 4 seconds or more Continuously for 4 seconds or more
Trip Count 1 trip 1 trip

HINT:

If the conditions of either of these patterns are detected, a DTC will be stored.


WIRING DIAGRAM

E407114E13
0.354,1.49 0.938,1.656 0.583,0.167 10 false A9 0.344,1.688 3.917,2.073 3.573,0.385 10 false Cooler Thermistor (Ambient Temperature Sensor) 4.635,1.813 6.948,2.073 2.313,0.26 10 false Air Conditioning Amplifier Assembly 3,0.5 3.177,0.719 0.177,0.219 10 false 2 3,0.969 3.177,1.188 0.177,0.219 10 false 1 4.427,0.979 4.667,1.198 0.24,0.219 10 false 14 4.49,0.521 4.677,0.708 0.188,0.188 10 false 1 4.792,0.531 5.229,0.719 0.438,0.188 10 false TAM 4.823,1.021 5.229,1.208 0.406,0.188 10 false SG-2 5.667,0.271 5.917,0.458 0.25,0.188 10 false 5 V 6.26,0.781 6.51,0.969 0.25,0.188 10 false AD 4.625,1.615 4.958,1.813 0.333,0.198 10 false I32

PROCEDURE

1.CHECK COOLER THERMISOTR (AMBIENT TEMPERATURE SENSOR) CIRCUIT

Pre-procedure1

a.

Disconnect the A9 cooler thermistor (ambient temperature sensor) connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A9)Location & Routing

Click Connector(A9)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Cooler (Ambient Temperature Sensor) Thermistor

A9-2 - Body ground Ignition switch ON 0 to 5.5 V



Post-procedure1

Result:
Proceed to
OK
NG


c.

None



OK

2.READ VALUE USING GTS (AMBIENT TEMPERATURE SENSOR)

NG

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER THERMISTOR (AMBIENT TEMPERATURE SENSOR))
2.READ VALUE USING GTS (AMBIENT TEMPERATURE SENSOR)

Pre-procedure1

a.

Disconnect the cooler thermistor (ambient temperature sensor) connector.


b.

Connect terminals 1 and 2 of the cooler thermistor (room temperature sensor) connector on the wire harness side.

E446846C04
4.427,1.271 4.844,1.51 0.417,0.24 1.094,2.042 1.417,2.344 0.323,0.302 10 false *1 3.104,2.031 3.427,2.333 0.323,0.302 10 false *2 4.802,0.531 5.125,0.833 0.323,0.302 10 false *a 2.521,1.01 2.844,1.313 0.323,0.302 10 false TAM 2.469,1.427 3.083,1.781 0.615,0.354 10 false SG-2 4.542,1.302 5.156,1.656 0.615,0.354 10 false A9
*1 Cooler Thermistor (Ambient Temperature Sensor) *2 Air Conditioning Amplifier Assembly
*a Front view of wire harness connector
(to Cooler Thermistor (Ambient Temperature Sensor))
- -



c.

According to the display on the GTS, read the Data List.

Body Electrical > Air Conditioner > Data List
Tester Display
Ambient Temperature Sensor
50003 450 101

OK:
GTS Display Specified Condition
Ambient Temperature Sensor 327.67°C (621.81°F)


Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

REPLACE COOLER THERMISTOR (AMBIENT TEMPERATURE SENSOR)

NG

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER THERMISTOR (AMBIENT TEMPERATURE SENSOR))
3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER THERMISTOR (AMBIENT TEMPERATURE SENSOR))

Pre-procedure1

a.

Disconnect the I32 air conditioning amplifier assembly connector.


b.

Disconnect the A9 cooler thermistor (ambient temperature sensor) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I32,A9)Location & Routing

Click Connector(I32)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Amplifier Assembly

Click Connector(A9)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Cooler (Ambient Temperature Sensor) Thermistor

I32-1 (TAM) - A9-2 Always Below 1 Ω
I32-14 (SG-2) - A9-1 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER THERMISTOR (AMBIENT TEMPERATURE SENSOR))

Pre-procedure1

a.

Disconnect the I32 air conditioning amplifier assembly connector.


b.

Disconnect the A9 cooler thermistor (ambient temperature sensor) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I32,A9)Location & Routing

Click Connector(I32)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Amplifier Assembly

Click Connector(A9)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Cooler (Ambient Temperature Sensor) Thermistor

I32-1 (TAM) or A9-2 - Other terminals and body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR