Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467925 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  P053011  Refrigerant Pressure Sensor Circuit Short to Ground  


DESCRIPTION

The air conditioning pressure sensor, which is installed to the high pressure side pipe to detect refrigerant pressure, sends a refrigerant pressure signal to the air conditioning amplifier assembly. The air conditioning amplifier assembly converts this signal to a pressure value according to the sensor characteristics and uses it to control the compressor.

This DTC is stored if refrigerant pressure on the high pressure side is extremely low.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
P053011 Refrigerant Pressure Sensor Circuit Short to Ground Diagnosis Condition:

Ignition switch ON


Malfunction Status:

Short (GND) in air conditioning pressure sensor circuit


Detection Time:

Continuously for 4 seconds or more


·

Refrigerant volume

·

Air conditioning pressure sensor

·

Harness or connector

·

Air conditioning amplifier assembly


Memorized Air Conditioner A

WIRING DIAGRAM

E316642E40
4.479,2.865 4.938,3.063 0.458,0.198 10 false I32 4.479,3.031 6.927,3.365 2.448,0.333 10 false Air Conditioning Amplifier Assembly 4.563,1.094 5.01,1.281 0.448,0.188 10 false S5-3 4.573,1.573 5.021,1.76 0.448,0.188 10 false PRE 4.563,2.031 5.01,2.219 0.448,0.188 10 false SG-4 4.229,1.094 4.677,1.281 0.448,0.188 10 false 11 4.292,1.573 4.74,1.76 0.448,0.188 10 false 6 4.24,2.042 4.688,2.229 0.448,0.188 10 false 15 1.99,1.083 2.438,1.271 0.448,0.188 10 false 3 2,1.573 2.448,1.76 0.448,0.188 10 false 2 2,2.042 2.448,2.229 0.448,0.188 10 false 1 1.656,1.563 2.104,1.75 0.448,0.188 10 false PR 1.74,1.083 2.188,1.271 0.448,0.188 10 false + 1.75,2.042 2.198,2.229 0.448,0.188 10 false - 0.375,2.563 0.833,2.76 0.458,0.198 10 false B22 0.375,2.708 2.823,3.042 2.448,0.333 10 false Air Conditioning Pressure Sensor 5.531,0.938 5.979,1.125 0.448,0.188 10 false 5 V 5.99,1.688 6.438,1.875 0.448,0.188 10 false AD

PROCEDURE

1.CHECK COMPARE REFRIGERANT GAS PRESSURE VALUES SHOWN ON GTS AND MANIFOLD GAUGE SET

Pre-procedure1

a.

Install a manifold gauge set.


Procedure1

b.

Compare the values displayed in the Data List and on the manifold gauge.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Regulator Pressure Sensor Air conditioning pressure sensor -32.768 to 32.767 MPaG Actual refrigerant pressure displayed
·

Refrigerant line (gas leak etc.)

·

Air conditioning pressure sensor circuit malfunction


Body Electrical > Air Conditioner > Data List
Tester Display
Regulator Pressure Sensor
50003 450 106
Result:
Result Proceed to
Data List value and manifold gauge set value do not match A
Data List value matches manifold gauge set value B



Post-procedure1

c.

None



A

2.READ VALUE USING GTS (REGULATOR PRESSURE SENSOR)

B

2.READ VALUE USING GTS (REGULATOR PRESSURE SENSOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Regulator Pressure Sensor Air conditioning pressure sensor -32.768 to 32.767 MPaG Actual refrigerant pressure displayed
·

Refrigerant line (gas leak etc.)

·

Air conditioning pressure sensor circuit malfunction


Body Electrical > Air Conditioner > Data List
Tester Display
Regulator Pressure Sensor
50003 450 106
OK:

Disconnecting the B22 connector of the air conditioning pressure sensor causes the Data List value to change.



Result:
Result Proceed to
Regulator pressure sensor value changes A
Regulator pressure sensor value does not change B



A

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING PRESSURE SENSOR - POWER SOURCE)

B

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING PRESSURE SENSOR - BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING PRESSURE SENSOR - POWER SOURCE)

Pre-procedure1

a.

Disconnect the B22 air conditioning pressure sensor connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B22)Location & Routing

Click Connector(B22)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Air Conditioning Pressure Sensor

B22-3 (+) - Body ground Ignition switch ON 4.75 to 5.25 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

NG

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

Pre-procedure1

a.

Disconnect the B22 air conditioning pressure sensor connector.


b.

Disconnect the I32 air conditioning amplifier assembly connector.


Procedure1


Post-procedure1

d.

None



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING PRESSURE SENSOR - BODY GROUND)

Pre-procedure1

a.

Disconnect the B22 air conditioning pressure sensor connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B22)Location & Routing

Click Connector(B22)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Air Conditioning Pressure Sensor

B22-2 (PR) - Body ground Ignition switch ON 3.0 to 5.25 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

Pre-procedure1

a.

Disconnect the B22 air conditioning pressure sensor connector.


b.

Disconnect the I32 air conditioning amplifier assembly connector.


Procedure1


Post-procedure1

d.

None



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR