Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467925 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Blower Motor Circuit  


DESCRIPTION

The blower motor with fan sub-assembly is operated by signals from the air conditioning amplifier assembly.

If the airflow volume is low or the blower speed cannot be changed, the following factors may be the cause.

Symptom Factor
Airflow volume cannot be changed
·

Air conditioning amplifier assembly malfunction

·

Blower motor with fan sub-assembly malfunction

·

Harness or connector



WIRING DIAGRAM

E316644E36
5.167,0.75 5.625,0.948 0.458,0.198 10 false BLW 4.885,0.75 5.344,0.948 0.458,0.198 10 false 21 5.177,1.521 5.635,1.719 0.458,0.198 10 false GND 4.896,1.406 5.354,1.604 0.458,0.198 10 false 17 6.073,0.875 6.531,1.073 0.458,0.198 10 false IC 2.563,0.615 3.021,0.813 0.458,0.198 10 false HTR 3.615,0.479 5.042,0.688 1.427,0.208 10 false from Battery 1.219,0.875 1.677,1.073 0.458,0.198 10 false IC 1.833,0.365 2.292,0.563 0.458,0.198 10 false +B 2.125,0.365 2.583,0.563 0.458,0.198 10 false 3 1.854,0.76 2.313,0.958 0.458,0.198 10 false SI 2.125,0.75 2.583,0.948 0.458,0.198 10 false 2 2.125,1.156 2.583,1.354 0.458,0.198 10 false 1 1.688,1.156 2.146,1.354 0.458,0.198 10 false GND 0.406,1.958 0.865,2.156 0.458,0.198 10 false I36 0.417,2.125 2.99,2.375 2.573,0.25 10 false Blower with Fan Motor Assembly 4.667,1.979 5.125,2.177 0.458,0.198 10 false I33 4.667,2.146 7.042,2.365 2.375,0.219 10 false Air Conditioning Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Blower Level Blower motor with fan sub-assembly operation Min.: 0
Max.: 31
-
Body Electrical > Air Conditioner > Active Test
Tester Display
Blower Level
50004 450 1

Result:
Result Proceed to
Blower motor with fan sub-assembly does not operate A
Blower motor with fan sub-assembly operates but does not change speed B



A

2.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BATTERY AND BODY GROUND)

B

5.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the I36 blower motor with fan sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I36)Location & Routing

Click Connector(I36)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Blower with Fan Motor Sub-Assembly

I36-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I36)Location & Routing

Click Connector(I36)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Blower with Fan Motor Sub-Assembly

I36-3 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)
a.

Disconnect the I33 air conditioning amplifier assembly connector.


b.

Disconnect the I36 blower motor with fan sub-assembly connector.



Result:
Proceed to
OK
NG



OK

4.CHECK BLOWER MOTOR WITH FAN SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK BLOWER MOTOR WITH FAN SUB-ASSEMBLY
a.

Disconnect the I33 air conditioning amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I33)Location & Routing

Click Connector(I33)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Amplifier Assembly

I33-21 (BLW) - Body ground Always 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

5.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE BLOWER MOTOR WITH FAN SUB-ASSEMBLY

5.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E349843C15
0.646,0.781 1.146,1.031 0.5,0.25 1.75,0.969 2,1.385 2,1.385 2.25,1.385 true 0.813,0.844 1.271,1.042 0.458,0.198 10 false I36 2.302,1.292 2.76,1.49 0.458,0.198 10 false SI 2.875,2.833 3.229,3.042 0.354,0.208 10 false GND 0.073,0.052 0.531,0.25 0.458,0.198 10 false *a
*a Component with harness connected
(Blower with Fan Motor Sub-assembly)


Using an oscilloscope, check the waveform.

Tester Connection Tool Setting Condition

Click Location & Routing(I36)Location & Routing

Click Connector(I36)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Blower with Fan Motor Sub-Assembly

I36-2 (SI) - Body ground 1 V/DIV., 500 μs./DIV.
·

Ignition switch ON

·

Blower speed: LO



HINT:

The waveform varies with the blower speed.


OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE BLOWER MOTOR WITH FAN SUB-ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY