Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467925 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Cooling is Poor  


DESCRIPTION

If the cooling effect of the air conditioning system is weak, the following factors may be the cause.

for Front:
Symptom Factor
·

Cooling is poor.

·

Takes time to cool down.


·

Customize setting

·

Cooler compressor assembly malfunction

·

Excessive refrigerant

·

Quantity of refrigerant gas lack

·

Dirty cooler condenser

·

Cooling fan system malfunction

·

A/M servo motor malfunction

·

Damper and link operation (jamming)

·

Automatic light control sensor malfunction

·

Warm air flow



for Rear (w/ Rear Cooler):
Symptom Factor
·

Cooling is poor.

·

Takes time to cool down.


·

Customize setting

·

Cooler compressor assembly malfunction

·

Excessive refrigerant

·

Quantity of refrigerant gas lack

·

Dirty cooler condenser

·

Cooling fan system malfunction

·

Warm air flow



for Rear (w/ Rear Air Conditioning System):
Symptom Factor
·

Cooling is poor.

·

Takes time to cool down.


·

Customize setting

·

Cooler compressor assembly malfunction

·

Excessive refrigerant

·

Quantity of refrigerant gas lack

·

Dirty cooler condenser

·

Cooling fan system malfunction

·

A/M servo motor malfunction

·

Damper and link operation (jamming)

·

Warm air flow



WIRING DIAGRAM

E366622E24
0.229,1.021 1.802,1.396 1.573,0.375 10 false Air Conditioning Amplifier Assembly 1.844,3.865 3.208,4.021 1.365,0.156 10 false K4 1.854,4.021 4.073,4.219 2.219,0.198 10 false Automatic Light Control Sensor 4.646,3.979 6.01,4.135 1.365,0.156 10 false I3 4.656,4.146 6.844,4.573 2.188,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 1.021,4.479 3.24,4.677 2.219,0.198 10 false : CAN Communication Line 4.594,1.646 5.052,1.823 0.458,0.177 10 false 8 4.885,1.646 5.344,1.823 0.458,0.177 10 false CLTB 4.594,2.427 5.052,2.604 0.458,0.177 10 false 20 4.906,2.427 5.365,2.604 0.458,0.177 10 false CLTS 4.615,3.094 5.073,3.271 0.458,0.177 10 false 21 4.906,3.083 5.365,3.26 0.458,0.177 10 false CLTE 3.104,1.646 3.563,1.823 0.458,0.177 10 false CLTB 3.625,1.656 4.083,1.833 0.458,0.177 10 false 1 3.125,2.438 3.583,2.615 0.458,0.177 10 false CLTS 3.615,2.427 4.073,2.604 0.458,0.177 10 false 4 3.615,3.104 4.073,3.281 0.458,0.177 10 false 2 3.125,3.115 3.583,3.292 0.458,0.177 10 false CLTE

PROCEDURE

1.CHECK ECO MODE SETTING
a.

Confirm that ECO HEAT/COOL switch is set to off.


b.

Confirm that ECO drive mode is set to off.

HINT:

When the ECO drive mode is set to ON, the air conditioning amplifier assembly performs minimal air conditioning control in order to promote the improvement of fuel economy. Ensure that the customer understands that the airflow volume will be decreased compared to normal operation.

Control Control Summary
Air Volume Control Sets the blower level to less.



Result:
Proceed to
NEXT



NEXT

2.CHECK REFRIGERANT SHORTAGE
2.CHECK REFRIGERANT SHORTAGE
a.

Prepare the vehicle according to the table below.

Measurement Condition:
Item Condition
Vehicle Condition Engine running
A/C Switch On
Ambient Temperature*1 0 to 49°C (32 to 120°F)
Air Conditioning Air Inlet Temperature*2 25 to 35°C (77 to 95°F)
Set Temperature MAX COLD
Recirculation/fresh Control Switch Recirculation
Air Vent Damper Position FACE
Blower Speed HI

HINT:

*1: This inspection can be judged correctly only if the ambient temperature is within a range of 0 to 49°C (32 to 120°F). Therefore, postpone the test if the temperature is low.

*2: This inspection can be judged correctly only if the air inlet temperature is within a range of 25 to 35°C (77 to 95°F). Therefore, postpone the test if the temperature is out of range.



b.

Using the GTS, check the amount of refrigerant.

Body Electrical > Air Conditioner > Utility
Tester Display
Refrigerant Gas Volume Check
50005 450 4578
NOTICE:

If the conditions for the inspection are not met, "Refrigerant incorrect" will be displayed on the GTS. Confirm the conditions of the inspection and perform the check again.


HINT:
·

If the amount of refrigerant is insufficient, "Refrigerant shortage" is displayed on the GTS and the indicator light on the A/C switch turns off.

·

When performing this inspection, a DTC will not be output even if "Refrigerant shortage" is displayed on the GTS.



Result:
Result Amount of Refrigerant
Refrigerant shortage Insufficient or leakage
Refrigerant correct Correct
Refrigerant incorrect Incorrect


OK:

"Refrigerant correct" is displayed on the GTS.



Result:
Result Proceed to
OK (for Front) A
OK (for Rear (w/ Rear Cooler)) B
OK (for Rear (w/ Rear Air Conditioning System)) C
NG D



A

3.PERFORM ACTIVE TEST USING GTS

B

C

6.PERFORM ACTIVE TEST USING GTS

D

3.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Left Air Mix Damper Control Servo Motor No. 2 air conditioning radiator damper servo sub-assembly operation 128: Min
384: Max
Operates between 254 to 326
FL Air Mix Cool Damper Control Servo Motor No. 2 air conditioning radiator damper servo sub-assembly operation 128: Min
384: Max
for Dual:

Operates between 154 to 258


for 4 Zone:

Operates between 254 to 358


Front Right Air Mix Damper Control Servo Motor No. 4 air conditioning radiator damper servo sub-assembly operation 128: Min
384: Max
Operates between 186 to 258
FR Air Mix Cool Damper Control Servo Motor No. 4 air conditioning radiator damper servo sub-assembly operation 128: Min
384: Max
Operates between 154 to 258
Fr Control RL Air Mix Damper Control Servo Motor No. 2 air conditioning radiator damper servo sub-assembly operation 128: Min
384: Max
Operates between 154 to 258
Fr Control RR Air Mix Damper Control Servo Motor No. 4 air conditioning radiator damper servo sub-assembly operation 128: Min
384: Max
Operates between 154 to 258
Body Electrical > Air Conditioner > Active Test
Tester Display
Front Left Air Mix Damper Control Servo Motor
50004 450 26 201
Body Electrical > Air Conditioner > Active Test
Tester Display
FL Air Mix Cool Damper Control Servo Motor
50004 450 27
Body Electrical > Air Conditioner > Active Test
Tester Display
Front Right Air Mix Damper Control Servo Motor
50004 450 28 205
Body Electrical > Air Conditioner > Active Test
Tester Display
FR Air Mix Cool Damper Control Servo Motor
50004 450 29
Body Electrical > Air Conditioner > Active Test
Tester Display
Fr Control RL Air Mix Damper Control Servo Motor
50004 450 36
Body Electrical > Air Conditioner > Active Test
Tester Display
Fr Control RR Air Mix Damper Control Servo Motor
50004 450 37
OK:

Damper servo motor is operated.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

GO TO DIAGNOSTIC TROUBLE CODE CHART (FOR SERVO MOTOR OF APPLICABLE ABNORMAL OPERATION)

4.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the K4 automatic light control sensor connector.


b.

Disconnect the I3 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K4,I3)Location & Routing

Click Connector(K4)Instrument Panel>No. 3 Instrument Panel Wire>Automatic Light Control Sensor

Click Connector(I3)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

K4-1 (CLTB) - I3-8 (CLTB) Always Below 1 Ω
K4-2 (CLTE) - I3-21 (CLTE) Always Below 1 Ω
K4-4 (CLTS) - I3-20 (CLTS) Always Below 1 Ω
K4-1 (CLTB) or I3-8 (CLTB) - Other terminals and body ground Always 10 kΩ or higher
K4-2 (CLTE) or I3-21 (CLTE) - Other terminals and body ground Always 10 kΩ or higher
K4-4 (CLTS) or I3-20 (CLTS) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

OK

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR

6.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Left Air Mix Damper Control Servo Motor Rear air mix damper servo sub-assembly operation Min.: 128
Max.: 384
Operates between 254 to 299 pulses
Rear Right Air Mix Damper Control Servo Motor No. 2 rear air mix damper servo sub-assembly operation Min.: 128
Max.: 384
Operates between 213 to 258 pulses
Rear Air Outlet Damper Control Servo Motor Rear mode damper servo sub-assembly operation Min.: 128
Max.: 384
Operates between 200 to 276 pulses
Body Electrical > Air Conditioner > Active Test
Tester Display
Rear Left Air Mix Damper Control Servo Motor
50004 450 42
Body Electrical > Air Conditioner > Active Test
Tester Display
Rear Right Air Mix Damper Control Servo Motor
50004 450 43
Body Electrical > Air Conditioner > Active Test
Tester Display
Rear Air Outlet Damper Control Servo Motor
50004 450 51
OK:

Damper servo motor is operated.



Result:
Proceed to
OK
NG



OK

NG

GO TO DIAGNOSTIC TROUBLE CODE CHART (FOR SERVO MOTOR OF APPLICABLE ABNORMAL OPERATION)