Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS
RM38G0E _59 Vehicle Exterior _100806 WINDOW / GLASS _0467978 QUARTER WINDOW GLASS A

WINDOW / GLASS  QUARTER WINDOW GLASS  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E463878N01
3.26,2.146 3.26,1.729 false 6.156,3.896 6.156,4.208 false 3.208,2.208 3.49,2.563 0.281,0.354 18 false 1 6.448,4.188 6.896,4.49 0.448,0.302 18 false 2 6.281,4.271 6.438,4.469 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ROOF HEADLINING ASSEMBLY 63311C - - -
2 QUARTER WINDOW ASSEMBLY LH 62720A (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the quarter window assembly removal/installation are shown below.

Necessary Procedures after parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for the RH and LH sides.

·

Use the same procedure described for the LH side.



PROCEDURE

Hide 63311C 1.REMOVE ROOF HEADLINING ASSEMBLY

Hide 62720A 2.REMOVE QUARTER WINDOW ASSEMBLY LH

Z101186

NOTICE:

The quarter window assembly LH may fall during work. Therefore, use suction cup to hold the quarter window assembly LH from outside the vehicle.



a.
E463879C01
4.021,1.208 4.333,1.406 0.313,0.198 10 false *a 1.958,0.073 2.24,0.427 0.281,0.354 18 false i
*a for Glass Breakage Sensor - -


i.

Disconnect each connector.



b.
E463880C01
4.677,0.74 5.542,0.74 true 0.344,0.021 0.625,0.375 0.281,0.354 18 false i 4.031,0.021 4.313,0.375 0.281,0.354 18 false ii 4.479,0.656 4.792,0.854 0.313,0.198 10 false *a
*a Suction Cup - -


i.

Apply protective tape on the body surface around the outer edge of the quarter window assembly LH.


ii.

Install the suction cup to the quarter window assembly LH.



c.
E463881C01
0.875,3.479 1.031,3.281 1.031,3.281 1.208,3.281 true 3.313,1.552 3.438,1.552 3.438,1.552 3.531,1.354 true 4.042,4.906 4.042,4.677 4.042,4.677 4.24,4.542 true 6.354,2.365 6.615,2.365 true 0.406,0.042 0.688,0.396 0.281,0.354 18 false i 2.594,3 2.75,3.198 0.156,0.198 10 false A 3.115,3 3.271,3.198 0.156,0.198 10 false A 3.333,2.188 3.49,2.385 0.156,0.198 10 false B 3.323,2.594 3.479,2.792 0.156,0.198 10 false B 3.594,3.042 3.75,3.24 0.156,0.198 10 false D 3.719,3.573 3.875,3.771 0.156,0.198 10 false D 4.031,2.927 4.188,3.125 0.156,0.198 10 false C 4.604,2.927 4.76,3.125 0.156,0.198 10 false C 0.531,3.104 0.99,3.302 0.458,0.198 10 false A-A 3.073,0.292 3.531,0.49 0.458,0.198 10 false B-B 5.083,2.083 5.542,2.281 0.458,0.198 10 false C-C 3.885,4.156 4.344,4.354 0.458,0.198 10 false D-D 1.24,3.188 1.552,3.385 0.313,0.198 10 false *a 3.156,1.469 3.469,1.667 0.313,0.198 10 false *a 6.177,2.271 6.49,2.469 0.313,0.198 10 false *a 3.969,4.917 4.281,5.115 0.313,0.198 10 false *a
*a Cut - -


i.

Using a utility knife, cut the position of the moulding shown in the illustration.

NOTICE:

If the body panel is damaged, perform rust-prevention treatment after removing the quarter window assembly LH.




d.
E463882C01
4.135,1 3.896,0.844 3.896,0.844 4.104,0.75 true 3.042,1.219 2.667,0.938 2.667,0.938 2.938,0.646 true 4.042,0.542 4.719,0.281 4.719,0.281 4.302,0.833 true 3.26,1.385 3.563,1.146 3.563,1.146 3.167,1.115 true 0.396,0.063 0.99,0.365 0.594,0.302 18 false i 3.594,1.042 3.792,1.219 0.198,0.177 10 true *a 3.667,0.771 3.875,0.948 0.208,0.177 10 true *b 2.448,0.854 2.656,1.021 0.208,0.167 10 true *b 4.76,0.167 5,0.375 0.24,0.208 10 false *a
*a Piano Wire *b Clip


i.

When using a piano wire, perform the following procedure.

1. Pass the piano wire (0.6 mm is appropriate) between the vehicle body and quarter window assembly LH from the interior.

2. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

3. Cut off the adhesive by pulling the piano wire around the quarter window assembly LH

NOTICE:
·

Do not forcefully allow the piano wire to come to contact with the edges of the quarter window assembly LH.

·

Be careful as the piano wire will break if it crosses itself.





e.
E463883N01
0.396,0.021 0.625,0.292 0.229,0.271 18 false i

i.

Holding the suction cup, remove the quarter window assembly LH.

NOTICE:

Be careful not to drop the quarter window assembly LH.