Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR
RM38G0E _59 Vehicle Exterior _100827 MIRROR (EXT) _0468032 OUTER REAR VIEW MIRROR G

MIRROR (EXT)  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87940 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Reverse Shift-linked Mirror)

a.

Check the operation of the mirror surface.

i.
B247200C04
1.458,1.844 1.938,2.073 0.479,0.229 2.552,3.219 1.938,3.219 1.938,3.219 1.938,2.969 true 1.844,2.969 1.844,3.229 1.844,3.229 1.094,3.229 true 2.073,2.885 2.469,2.885 true 1.021,2.25 1.188,2.406 0.167,0.156 10 false *a 2.625,3.135 2.885,3.323 0.26,0.188 10 false M+ 0.854,3.156 1.219,3.385 0.365,0.229 10 false MH 2.531,2.802 2.854,2.969 0.323,0.167 10 false MV 1.594,1.885 2.052,2.083 0.458,0.198 10 false N21
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply battery voltage and check the operation of the mirror.

OK:
Tester Connection Specified Condition

Click Location & Routing(N21)Location & Routing

Click Connector(N21)Body>Front Door Wire LH>Outer Rear View Mirror Assembly LH

Battery positive (+) - N21-3 (MV)
Battery negative (-) - N21-7 (M+)
Turns upward
Battery positive (+) - N21-7 (M+)
Battery negative (-) - N21-3 (MV)
Turns downward
Battery positive (+) - N21-7 (M+)
Battery negative (-) - N21-6 (MH)
Turns inside
Battery positive (+) - N21-6 (MH)
Battery negative (-) - N21-7 (M+)
Turns outside


If the result is not as specified, replace the outer rear view mirror assembly LH.



b.

Check the side turn signal light assembly LH.

i.
B607326C01
1.406,0.125 1.896,0.333 0.49,0.208 0.781,1.552 1.167,1.552 true 0.823,2.063 1.396,2.063 1.396,2.063 1.396,1.646 true 0.521,0.594 0.833,0.792 0.313,0.198 10 false *a 0.677,1.979 0.833,2.177 0.156,0.198 10 false B 0.646,1.469 0.802,1.667 0.156,0.198 10 false - 1.521,0.156 1.979,0.354 0.458,0.198 10 false N21
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(N21)Location & Routing

Click Connector(N21)Body>Front Door Wire LH>Outer Rear View Mirror Assembly LH

Battery positive (+) - N21-5 (B)
Battery negative (-) - N21-4 (-)
Side turn signal light illuminates


If the result is not as specified, inspect the side turn signal light assembly LH or replace the outer rear view mirror assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION



Hide 87966 2.INSPECT OUTER MIRROR RETRACTOR LH (w/o Reverse Shift-linked Mirror)

a.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.



i.
B607322C01
1.49,2.156 1.979,2.375 0.49,0.219 2.406,2.948 2.042,2.948 true 1.917,2.927 1.917,2.427 1.917,2.427 2.417,2.427 true 1.521,0.104 1.688,0.281 0.167,0.177 10 false *a 0.938,0.729 1.104,0.906 0.167,0.177 10 false *b 1.083,1.604 1.25,1.781 0.167,0.177 10 false *c 1.49,1.865 1.656,2.042 0.167,0.177 10 false *d 2.094,1.896 2.26,2.073 0.167,0.177 10 false *e 1.083,2.469 1.25,2.625 0.167,0.156 10 false *f 2.51,2.354 2.833,2.51 0.323,0.156 10 false MR 2.469,2.885 2.719,3.042 0.25,0.156 10 false MF 1.615,2.188 2.073,2.385 0.458,0.198 10 false N21
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(N21)Location & Routing

Click Connector(N21)Body>Front Door Wire LH>Outer Rear View Mirror Assembly LH

Battery positive (+) - N21-1 (MR)
Battery negative (-) - N21-2 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) - N21-2 (MF)
Battery negative (-) - N21-1 (MR)
Forward position (A) Does not move
Battery positive (+) - N21-1 (MR)
Battery negative (-) - N21-2 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) - N21-2 (MF)
Battery negative (-) - N21-1 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) - N21-1 (MR)
Battery negative (-) - N21-2 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) - N21-2 (MF)
Battery negative (-) - N21-1 (MR)
Driving position (C) Does not move
Battery positive (+) - N21-1 (MR)
Battery negative (-) - N21-2 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) - N21-2 (MF)
Battery negative (-) - N21-1 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) - N21-1 (MR)
Battery negative (-) - N21-2 (MF)
Retracted position (E) Does not move
Battery positive (+) - N21-2 (MF)
Battery negative (-) - N21-1 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor LH.



Hide 87910 3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Reverse Shift-linked Mirror)

a.

Check the operation of the mirror surface.

i.
B240781C05
1.458,1.844 1.938,2.073 0.479,0.229 2.552,3.219 1.938,3.219 1.938,3.219 1.938,2.969 true 1.844,2.969 1.844,3.229 1.844,3.229 1.094,3.229 true 2.073,2.885 2.469,2.885 true 1.021,2.25 1.188,2.406 0.167,0.156 10 false *a 2.625,3.135 2.885,3.323 0.26,0.188 10 false M+ 0.854,3.156 1.219,3.385 0.365,0.229 10 false MH 2.531,2.802 2.854,2.969 0.323,0.167 10 false MV 1.594,1.885 2.052,2.083 0.458,0.198 10 false M21
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply battery voltage and check the operation of the mirror.

OK:
Tester Connection Specified Condition

Click Location & Routing(M21)Location & Routing

Click Connector(M21)Body>Front Door Wire RH>Outer Rear View Mirror Assembly RH

Battery positive (+) - M21-3 (MV)
Battery negative (-) - M21-7 (M+)
Turns upward
Battery positive (+) - M21-7 (M+)
Battery negative (-) - M21-3 (MV)
Turns downward
Battery positive (+) - M21-6 (MH)
Battery negative (-) - M21-7 (M+)
Turns inside
Battery positive (+) - M21-7 (M+)
Battery negative (-) - M21-6 (MH)
Turns outside


If the result is not as specified, replace the outer rear view mirror assembly RH.



b.

Check the side turn signal light assembly RH.

i.
B607326C02
1.406,0.125 1.896,0.333 0.49,0.208 0.781,1.552 1.167,1.552 true 0.823,2.063 1.396,2.063 1.396,2.063 1.396,1.646 true 0.521,0.594 0.833,0.792 0.313,0.198 10 false *a 0.677,1.979 0.833,2.177 0.156,0.198 10 false B 0.646,1.469 0.802,1.667 0.156,0.198 10 false - 1.521,0.156 1.979,0.354 0.458,0.198 10 false M21
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(M21)Location & Routing

Click Connector(M21)Body>Front Door Wire RH>Outer Rear View Mirror Assembly RH

Battery positive (+) - M21-5 (B)
Battery negative (-) - M21-4 (-)
Side turn signal light illuminates


If the result is not as specified, inspect the side turn signal light assembly RH or replace the outer rear view mirror assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION



Hide 87946 4.INSPECT OUTER MIRROR RETRACTOR RH (w/o Reverse Shift-linked Mirror)

a.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.



i.
B607324C01
1.542,2.156 1.927,2.375 0.385,0.219 2.406,2.948 2.042,2.948 true 1.917,2.927 1.917,2.427 1.917,2.427 2.417,2.427 true 1.823,0.063 1.99,0.24 0.167,0.177 10 false *a 2.448,0.76 2.615,0.938 0.167,0.177 10 false *b 2.271,1.604 2.438,1.781 0.167,0.177 10 false *c 1.844,1.865 2.01,2.042 0.167,0.177 10 false *d 1.26,1.865 1.427,2.042 0.167,0.177 10 false *e 1.083,2.469 1.25,2.625 0.167,0.156 10 false *f 2.51,2.354 2.833,2.51 0.323,0.156 10 false MR 2.469,2.885 2.719,3.042 0.25,0.156 10 false MF 1.604,2.188 2.063,2.385 0.458,0.198 10 false M21
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(M21)Location & Routing

Click Connector(M21)Body>Front Door Wire RH>Outer Rear View Mirror Assembly RH

Battery positive (+) - M21-1 (MR)
Battery negative (-) - M21-2 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) - M21-2 (MF)
Battery negative (-) - M21-1 (MR)
Forward position (A) Does not move
Battery positive (+) - M21-1 (MR)
Battery negative (-) - M21-2 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) - M21-2 (MF)
Battery negative (-) - M21-1 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) - M21-1 (MR)
Battery negative (-) - M21-2 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) - M21-2 (MF)
Battery negative (-) - M21-1 (MR)
Driving position (C) Does not move
Battery positive (+) - M21-1 (MR)
Battery negative (-) - M21-2 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) - M21-2 (MF)
Battery negative (-) - M21-1 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) - M21-1 (MR)
Battery negative (-) - M21-2 (MF)
Retracted position (E) Does not move
Battery positive (+) - M21-2 (MF)
Battery negative (-) - M21-1 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor RH.



Hide 87940 5.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Reverse Shift-linked Mirror)

a.

Check the operation of the mirror surface.

i.
B199931C38
1.552,1.667 1.875,1.875 0.323,0.208 1.25,2.667 0.917,2.667 true 1.406,3.167 1.406,2.896 true 0.906,2.854 1.24,2.854 true 0.573,1.948 0.885,2.104 0.313,0.156 10 false *a 0.667,2.594 0.979,2.792 0.313,0.198 10 false MV 0.656,2.781 0.969,2.979 0.313,0.198 10 false MH 1.344,3.219 1.656,3.417 0.313,0.198 10 false M+ 1.604,1.688 1.885,1.896 0.281,0.208 10 false z10
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply battery voltage and check the operation of the mirror.

OK:
Tester Connection Specified Condition

Click Location & Routing(z10)Location & Routing

Click Connector(z10)Body>other>Outer Rear View Mirror Assembly LH , Outer Mirror Control ECU Assembly LH

Battery positive (+) - z10-1 (MV)
Battery negative (-) - z10-10 (M+)
Turns upward
Battery positive (+) - z10-10 (M+)
Battery negative (-) - z10-1 (MV)
Turns downward
Battery positive (+) - z10-10 (M+)
Battery negative (-) - z10-9 (MH)
Turns inside
Battery positive (+) - z10-9 (MH)
Battery negative (-) - z10-10 (M+)
Turns outside


If the result is not as specified, replace the outer rear view mirror assembly LH.



b.

Check the side turn signal light assembly LH.

i.
B580872C37
1.51,0.344 1.896,0.594 0.385,0.25 2.125,1.563 2.448,1.563 true 1.573,1.583 1.573,1.927 1.573,1.927 1.74,1.927 true 0.448,0.24 0.76,0.396 0.313,0.156 10 false *a 1.802,1.844 2.417,2.042 0.615,0.198 10 false TRN- 2.5,1.479 3.115,1.677 0.615,0.198 10 false TRN+ 1.594,0.396 2.052,0.594 0.458,0.198 10 false z10
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(z10)Location & Routing

Click Connector(z10)Body>other>Outer Rear View Mirror Assembly LH , Outer Mirror Control ECU Assembly LH

Battery positive (+) - z10-16 (TRN+)
Battery negative (-) - z10-12 (TRN-)
Side turn signal light illuminates


If the result is not as specified, inspect the side turn signal light assembly LH or replace the outer rear view mirror assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION



c.

w/ Mirror Heater:

Check the operation of the mirror heater.

i.
B580872C36
1.448,0.354 1.854,0.583 0.406,0.229 1.594,1.594 1.594,1.906 true 1.573,1.417 0.917,1.417 true 0.74,0.76 1.052,0.917 0.313,0.156 10 false *a 1.51,1.927 2.125,2.125 0.615,0.198 10 false H/T- 0.76,1.333 0.927,1.531 0.167,0.198 10 false + 1.542,0.375 2,0.573 0.458,0.198 10 false z10
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z10)Location & Routing

Click Connector(z10)Body>other>Outer Rear View Mirror Assembly LH , Outer Mirror Control ECU Assembly LH

z10-4 (+) - z10-12 (H/T-) 25 °C (77 °F) 3.9 to 5.3 Ω



iii.

Connect the cable from the positive (+) battery terminal to z10 terminal 4 (+) and the negative (-) battery terminal to z10 terminal 12 (-), and then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, inspect the outer mirror LH or replace the outer mirror actuator assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION



d.

w/ Foot Light:

Check the mirror light illumination.

i.
B580872C35
1.438,0.323 1.865,0.573 0.427,0.25 1.573,1.563 1.573,1.896 true 0.823,1.385 1.302,1.385 true 0.719,0.75 1.031,0.906 0.313,0.156 10 false *a 0.531,1.323 0.948,1.531 0.417,0.208 10 false MLP 1.469,1.927 1.906,2.125 0.438,0.198 10 false H/T- 1.542,0.375 2,0.573 0.458,0.198 10 false z10
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(z10)Location & Routing

Click Connector(z10)Body>other>Outer Rear View Mirror Assembly LH , Outer Mirror Control ECU Assembly LH

Battery positive (+) - z10-2 (MLP)
Battery negative (-) - z10-12 (H/T-)
Mirror light illuminates


If the result is not as specified, replace the outer rear view mirror assembly LH.



e.
B580872C34
1.438,0.292 1.844,0.542 0.406,0.25 1.604,1.563 1.604,1.875 true 2.146,1.396 2.406,1.396 true 0.76,0.792 1.073,0.948 0.313,0.156 10 false *a 1.469,1.906 2,2.115 0.531,0.208 10 false BSM- 2.458,1.313 2.979,1.5 0.521,0.188 10 false BSM+ 1.542,0.354 2,0.552 0.458,0.198 10 false z10
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


w/ Blind Spot Monitor System:

Check the operation of the blind spot monitor indicator.

i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.

Apply 6 V dry-cell batteries to the terminals of the connector, and check the blind spot monitor indicator condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(z10)Location & Routing

Click Connector(z10)Body>other>Outer Rear View Mirror Assembly LH , Outer Mirror Control ECU Assembly LH

Positive (+) end of the 6 V dry-cell battery - z10-8 (BSM+)
Negative (-) end of the 6 V dry-cell battery - z10-12 (BSM-)
Blind spot monitor indicator comes on


NOTICE:

Do not apply a voltage of 6 V or higher.


If the result is not as specified, inspect the outer mirror LH or replace the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION



f.

w/ EC Mirror:

Check the EC mirror operation.

i.

Connect a new 1.5 V dry-cell battery.


ii.
B236659C11
1.479,1.51 1.885,1.771 0.406,0.26 2.042,2.813 2.042,3.125 true 2,2.583 2,2.417 2,2.417 2.5,2.417 true 0.677,1.906 1.115,2.198 0.438,0.292 10 false *a 2.573,2.354 3.063,2.677 0.49,0.323 10 false EC+ 1.938,3.146 2.323,3.344 0.385,0.198 10 false EC- 2.656,1.219 3.094,1.51 0.438,0.292 10 false *b 0.573,1.198 1.01,1.49 0.438,0.292 10 false *c 1.563,1.552 1.875,1.708 0.313,0.156 10 false z10
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)
*b Bright
*c Dark


Apply 1.5 V dry-cell battery voltage and check operation of the mirror face as shown in the table and illustration.

OK:
Tester Connection Specified Condition

Click Location & Routing(z10)Location & Routing

Click Connector(z10)Body>other>Outer Rear View Mirror Assembly LH , Outer Mirror Control ECU Assembly LH

Positive (+) end of the 1.5 V dry-cell battery - z10-7 (EC+)
Negative (-) end of the 1.5 V dry-cell battery - z10-15 (EC-)
Mirror surface becomes dark


NOTICE:

Do not apply a voltage of 1.5 V or higher.


If the result is not as specified, inspect the outer mirror LH or replace the outer mirror retractor LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION



Hide 87966 6.INSPECT OUTER MIRROR RETRACTOR LH (w/ Reverse Shift-linked Mirror)

a.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.



i.
B237099C42
1.531,2.99 1.927,3.167 0.396,0.177 1.604,3.958 1.604,3.792 1.604,3.792 1.021,3.792 true 1.604,4.146 1.583,4.417 1.583,4.417 1.083,4.417 true 1.719,0.073 2.031,0.229 0.313,0.156 10 false *a 1.219,1.01 1.531,1.167 0.313,0.156 10 false *b 1.396,2.156 1.708,2.313 0.313,0.156 10 false *c 1.938,2.51 2.25,2.667 0.313,0.156 10 false *d 2.469,2.76 2.781,2.917 0.313,0.156 10 false *e 0.74,3.302 1.052,3.458 0.313,0.156 10 false *f 0.729,3.719 1.042,3.917 0.313,0.198 10 false MR 0.844,4.333 1.156,4.531 0.313,0.198 10 false MF 1.615,3 1.948,3.208 0.333,0.208 10 false z10
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(z10)Location & Routing

Click Connector(z10)Body>other>Outer Rear View Mirror Assembly LH , Outer Mirror Control ECU Assembly LH

Battery positive (+) - z10-3 (MR)
Battery negative (-) - z10-11 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) - z10-11 (MF)
Battery negative (-) - z10-3 (MR)
Forward position (A) Does not move
Battery positive (+) - z10-3 (MR)
Battery negative (-) - z10-11 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) - z10-11 (MF)
Battery negative (-) - z10-3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) - z10-3 (MR)
Battery negative (-) - z10-11 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) - z10-11 (MF)
Battery negative (-) - z10-3 (MR)
Driving position (C) Does not move
Battery positive (+) - z10-3 (MR)
Battery negative (-) - z10-11 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) - z10-11 (MF)
Battery negative (-) - z10-3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) - z10-3 (MR)
Battery negative (-) - z10-11 (MF)
Retracted position (E) Does not move
Battery positive (+) - z10-11 (MF)
Battery negative (-) - z10-3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor LH.



Hide 87910 7.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Reverse Shift-linked Mirror)

a.

Check the operation of the mirror surface.

i.
B199930C41
1.51,1.635 1.917,1.854 0.406,0.219 1.25,2.635 0.917,2.635 true 1.229,2.854 0.896,2.854 true 1.406,2.896 1.406,3.125 true 0.646,1.938 0.958,2.094 0.313,0.156 10 false *a 0.667,2.573 0.979,2.771 0.313,0.198 10 false MV 0.635,2.792 0.948,2.99 0.313,0.198 10 false MH 1.323,3.146 1.635,3.344 0.313,0.198 10 false M+ 1.635,1.677 1.948,1.875 0.313,0.198 10 false z9
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply battery voltage and check the operation of the mirror.

OK:
Tester Connection Specified Condition

Click Location & Routing(z9)Location & Routing

Click Connector(z9)Body>other>Outer Rear View Mirror Assembly RH , Outer Mirror Control ECU Assembly RH

Battery positive (+) - z9-1 (MV)
Battery negative (-) - z9-10 (M+)
Turns upward
Battery positive (+) - z9-10 (M+)
Battery negative (-) - z9-1 (MV)
Turns downward
Battery positive (+) - z9-9 (MH)
Battery negative (-) - z9-10 (M+)
Turns inside
Battery positive (+) - z9-10 (M+)
Battery negative (-) - z9-9 (MH)
Turns outside


If the result is not as specified, replace the outer rear view mirror assembly RH.



b.

Check the side turn signal light assembly RH.

i.
B580872C38
1.51,0.344 1.896,0.594 0.385,0.25 2.125,1.563 2.448,1.563 true 1.573,1.583 1.573,1.927 1.573,1.927 1.74,1.927 true 0.448,0.24 0.76,0.396 0.313,0.156 10 false *a 1.802,1.844 2.417,2.042 0.615,0.198 10 false TRN- 2.5,1.479 3.115,1.677 0.615,0.198 10 false TRN+ 1.615,0.396 2.073,0.594 0.458,0.198 10 false z9
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(z9)Location & Routing

Click Connector(z9)Body>other>Outer Rear View Mirror Assembly RH , Outer Mirror Control ECU Assembly RH

Battery positive (+) - z9-16 (TRN+)
Battery negative (-) - z9-12 (TRN-)
Side turn signal light illuminates


If the result is not as specified, inspect the side turn signal light assembly RH or replace the outer rear view mirror assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION



c.

w/ Mirror Heater:

Check the operation of the mirror heater.

i.
B580872C39
1.448,0.354 1.854,0.583 0.406,0.229 1.594,1.594 1.594,1.906 true 1.573,1.417 0.917,1.417 true 0.74,0.76 1.052,0.917 0.313,0.156 10 false *a 1.5,1.906 2.115,2.104 0.615,0.198 10 false H/T- 0.76,1.333 0.927,1.531 0.167,0.198 10 false + 1.573,0.396 2.031,0.594 0.458,0.198 10 false z9
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z9)Location & Routing

Click Connector(z9)Body>other>Outer Rear View Mirror Assembly RH , Outer Mirror Control ECU Assembly RH

z9-4 (+) - z9-12 (H/T-) 25 °C (77 °F) 3.9 to 5.3 Ω



iii.

Connect the cable from the positive (+) battery terminal to z9 terminal 4 (+) and the negative (-) battery terminal to z9 terminal 12 (-), and then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, inspect the outer mirror RH or replace the outer mirror actuator assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION



d.

w/ Foot Light:

Check the mirror light illumination.

i.
B580872C43
1.438,0.323 1.865,0.573 0.427,0.25 1.573,1.563 1.573,1.896 true 0.823,1.385 1.302,1.385 true 0.719,0.75 1.031,0.906 0.313,0.156 10 false *a 0.531,1.323 0.948,1.531 0.417,0.208 10 false MLP 1.438,1.927 1.875,2.125 0.438,0.198 10 false H/T- 1.563,0.375 2.021,0.573 0.458,0.198 10 false z9
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(z9)Location & Routing

Click Connector(z9)Body>other>Outer Rear View Mirror Assembly RH , Outer Mirror Control ECU Assembly RH

Battery positive (+) - z9-2 (MLP)
Battery negative (-) - z9-12 (H/T-)
Mirror light illuminates


If the result is not as specified, replace the outer rear view mirror assembly RH.



e.
B580872C42
1.438,0.292 1.844,0.542 0.406,0.25 1.604,1.563 1.604,1.875 true 2.146,1.396 2.406,1.396 true 0.76,0.792 1.073,0.948 0.313,0.156 10 false *a 1.469,1.885 2.094,2.115 0.625,0.229 10 false BSM- 2.458,1.313 2.979,1.5 0.521,0.188 10 false BSM+ 1.552,0.344 2.01,0.542 0.458,0.198 10 false z9
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


w/ Blind Spot Monitor System:

Check the operation of the blind spot monitor indicator.

i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.

Apply 6 V dry-cell batteries to the terminals of the connector, and check the blind spot monitor indicator condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(z9)Location & Routing

Click Connector(z9)Body>other>Outer Rear View Mirror Assembly RH , Outer Mirror Control ECU Assembly RH

Positive (+) end of the 6 V dry-cell battery - z9-8 (BSM+)
Negative (-) end of the 6 V dry-cell battery - z9-12 (BSM-)
Blind spot monitor indicator comes on


NOTICE:

Do not apply a voltage of 6 V or higher.


If the result is not as specified, inspect the outer mirror RH or replace the outer rear view mirror assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION



f.

w/ EC Mirror:

Check the EC mirror operation.

i.

Connect a new 1.5 V dry-cell battery.


ii.
B236658C13
1.479,1.51 1.885,1.771 0.406,0.26 2.052,2.792 2.052,3.104 true 2.052,2.542 2.052,2.375 2.052,2.375 2.552,2.375 true 0.677,1.906 1.115,2.198 0.438,0.292 10 false *a 2.677,2.281 3.167,2.604 0.49,0.323 10 false EC+ 1.938,3.146 2.323,3.344 0.385,0.198 10 false EC- 0.656,1.198 1.094,1.49 0.438,0.292 10 false *b 2.76,1.156 3.198,1.448 0.438,0.292 10 false *c 1.615,1.573 1.927,1.729 0.313,0.156 10 false z9
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)
*b Bright
*c Dark


Apply 1.5 V dry-cell battery voltage and check operation of the mirror face as shown in the table and illustration.

OK:
Tester Connection Specified Condition

Click Location & Routing(z9)Location & Routing

Click Connector(z9)Body>other>Outer Rear View Mirror Assembly RH , Outer Mirror Control ECU Assembly RH

Positive (+) end of the 1.5 V dry-cell battery - z9-7 (EC+)
Negative (-) end of the 1.5 V dry-cell battery - z9-15 (EC-)
Mirror surface becomes dark


NOTICE:

Do not apply a voltage of 1.5 V or higher.


If the result is not as specified, inspect the outer mirror RH or replace the outer mirror retractor RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION



Hide 87946 8.INSPECT OUTER MIRROR RETRACTOR RH (w/ Reverse Shift-linked Mirror)

a.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.



i.
B237589C43
1.552,2.917 1.865,3.167 0.313,0.25 1.552,4.167 1.552,4.333 1.552,4.333 1,4.333 true 1.552,3.979 1.552,3.813 1.552,3.813 1.052,3.813 true 1.677,0.052 1.99,0.208 0.313,0.156 10 false *a 2.125,1.094 2.438,1.25 0.313,0.156 10 false *b 1.865,2.052 2.177,2.208 0.313,0.156 10 false *c 1.385,2.354 1.698,2.51 0.313,0.156 10 false *d 0.885,2.635 1.198,2.792 0.313,0.156 10 false *e 0.552,3.396 0.865,3.552 0.313,0.156 10 false *f 0.813,3.75 1.125,3.948 0.313,0.198 10 false MR 0.76,4.25 1.073,4.448 0.313,0.198 10 false MF 1.615,2.969 2.073,3.167 0.458,0.198 10 false z9
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(z9)Location & Routing

Click Connector(z9)Body>other>Outer Rear View Mirror Assembly RH , Outer Mirror Control ECU Assembly RH

Battery positive (+) - z9-3 (MR)
Battery negative (-) - z9-11 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) - z9-11 (MF)
Battery negative (-) - z9-3 (MR)
Forward position (A) Does not move
Battery positive (+) - z9-3 (MR)
Battery negative (-) - z9-11 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) - z9-11 (MF)
Battery negative (-) - z9-3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) - z9-3 (MR)
Battery negative (-) - z9-11 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) - z9-11 (MF)
Battery negative (-) - z9-3 (MR)
Driving position (C) Does not move
Battery positive (+) - z9-3 (MR)
Battery negative (-) - z9-11 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) - z9-11 (MF)
Battery negative (-) - z9-3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) - z9-3 (MR)
Battery negative (-) - z9-11 (MF)
Retracted position (E) Does not move
Battery positive (+) - z9-11 (MF)
Battery negative (-) - z9-3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor RH.