Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE › 2021.04–2021.07
RM38G0E _59 Vehicle Exterior _100846 EXTERIOR PANELS / TRIM _0468072 NAME PLATE A

EXTERIOR PANELS / TRIM  NAME PLATE  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B609604N02
4.667,3.25 4.167,3.25 false 3.625,1.073 3.865,0.615 3.865,0.615 4.979,0.615 true 1.979,1.479 3.146,1.479 3.146,1.479 3.281,1.292 true 6.25,4.146 6,4.146 false 1.188,4.146 0.938,4.146 false 5.083,1.458 3.917,1.458 3.917,1.458 3.813,1.271 true 5.021,3.156 5.49,3.427 0.469,0.271 10 false (1) ● 6.542,4.063 7,4.333 0.458,0.271 10 false (3) ● 0.448,4.083 0.885,4.344 0.438,0.26 10 false (2) ● 5.375,3.073 5.656,3.427 0.281,0.354 18 false 1 0.813,4 1.094,4.354 0.281,0.354 18 false 2 6.917,3.99 7.104,4.344 0.188,0.354 18 false 3 5.031,0.51 5.49,0.708 0.458,0.198 10 false (1) 1.76,1.406 1.99,1.802 0.229,0.396 10 false (2) 5.156,1.375 5.385,1.646 0.229,0.271 10 false (3)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 SYMBOL EMBLEM 75741E (Click here) - -
2 BACK DOOR NAME PLATE 75441B (Click here) - -
3 BACK DOOR NAME PLATE 75441C (Click here) - -

● Non-reusable part - -

B609605N03
5.427,1.625 4.542,1.625 4.542,1.625 4.427,1.448 true 5.75,4.083 6.167,4.083 false 5.833,3.25 6.167,3.25 false 3.667,3.26 4,3.26 false 1.104,4.083 1.354,4.083 false 0.917,3.281 1,3.281 false 0.458,3.198 0.927,3.469 0.469,0.271 10 false (1) ● 0.76,3.135 1.042,3.49 0.281,0.354 18 false 4 5.479,1.542 5.708,1.813 0.229,0.271 10 false (1) 0.927,3.969 1.208,4.323 0.281,0.354 18 false 4 0.604,4.021 1.073,4.292 0.469,0.271 10 false (1) ● 6.469,3.198 6.938,3.469 0.469,0.271 10 false (1) ● 4.604,3.146 4.885,3.5 0.281,0.354 18 false 4 4.302,3.198 4.771,3.469 0.469,0.271 10 false (1) ● 6.792,3.135 7.073,3.49 0.281,0.354 18 false 4 6.5,4.01 6.969,4.281 0.469,0.271 10 false (1) ● 6.823,3.948 7.104,4.302 0.281,0.354 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

4 REAR BODY NO. 3 NAME PLATE 75473B (Click here) - -

● Non-reusable part - -

PROCEDURE

Hide 75741E 1.INSTALL SYMBOL EMBLEM

Z101186

NOTICE:

When installing a new symbol emblem, heat the back door outside garnish and symbol emblem using a heat light.



Standard Value:
Part Temperature
Back Door Outside Garnish 20 to 30°C (68 to 86°F)
Symbol Emblem 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the back door outside garnish and symbol emblem excessively.


a.
B609614C01
2.708,2.448 3.875,2.448 3.875,2.448 3.875,1.531 true 3.146,2.448 3.146,1.615 true 5.542,0.26 5.823,0.615 0.281,0.354 18 false i 5.542,1.417 5.823,1.771 0.281,0.354 18 false ii 2.51,0.531 2.75,0.813 0.24,0.281 18 true iii 2.573,2.354 2.771,2.594 0.198,0.24 10 true *a
*a Boss Position - -


i.

Clean the surface of the back door outside garnish.

1. Using a heat light, heat the back door outside garnish surface.

2. Remove any remaining double-sided tape from the back door outside garnish.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the symbol emblem with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Using a heat light, heat the back door outside garnish and a new symbol emblem.


iii.

Align the boss positions and install the symbol emblem.

NOTICE:

The application strength of the symbol emblem will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the back door outside garnish.




Hide 75441B 2.INSTALL BACK DOOR NAME PLATE

Z101186

NOTICE:

When installing a new rear back door name plate, heat the back door outside garnish and back door name plate using a heat light.



Standard Value:
Part Temperature
Back Door Outside Garnish 20 to 30°C (68 to 86°F)
Back Door Name Plate 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the back door outside garnish and back door name plate excessively.


a.
B609615C01
4.792,1.219 5.625,1.219 true 2.917,1.667 3.167,1.25 true 2.771,1.719 3.01,1.927 0.24,0.208 10 true *a 0.677,0.25 0.958,0.604 0.281,0.354 18 false i 0.667,1.385 0.948,1.74 0.281,0.354 18 false ii 2.802,0.646 3.083,1 0.281,0.354 18 false iii 5.656,1.135 5.896,1.344 0.24,0.208 10 true *a
*a Boss Position - -


i.

Clean the surface of the back door outside garnish.

1. Using a heat light, heat the back door outside garnish surface.

2. Remove any remaining double-sided tape from the back door outside garnish.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the back door name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Using a heat light, heat the back door outside garnish and a new back door name plate.


iii.

Align the boss positions and install the back door name plate as shown in the illustration.

NOTICE:

The application strength of the back door name plate will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the back door outside garnish.




Hide 75441C 3.INSTALL BACK DOOR NAME PLATE

Z101186

NOTICE:

When installing a new rear back door name plate, heat the back door outside garnish and back door name plate using a heat light.



Standard Value:
Part Temperature
Back Door Outside Garnish 20 to 30°C (68 to 86°F)
Back Door Name Plate 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the back door outside garnish and back door name plate excessively.


a.
B609616C01
3.083,0.833 2.833,1.167 true 6.573,0.427 6.156,0.76 true 4.823,2.021 5.073,2.021 true 4.813,2.354 5.063,2.354 true 0.667,0.271 0.948,0.625 0.281,0.354 18 false i 0.667,1.417 0.948,1.771 0.281,0.354 18 false ii 6.615,0.302 6.854,0.563 0.24,0.26 10 true *a 2.708,0.302 2.969,0.573 0.26,0.271 18 true iii 2.688,1.177 2.927,1.438 0.24,0.26 10 true *a 5.01,1.146 5.167,1.344 0.156,0.198 10 true A 5.021,0.417 5.177,0.615 0.156,0.198 10 true A 4.604,1.573 5.177,1.781 0.573,0.208 10 true A - A 5.135,2.281 5.375,2.542 0.24,0.26 10 true *b 5.115,1.948 5.354,2.208 0.24,0.26 10 true *b
*a Boss Position *b Back Door Outside Garnish Positioning Rib


i.

Clean the surface of the back door outside garnish.

1. Using a heat light, heat the back door outside garnish surface.

2. Remove any remaining double-sided tape from the back door outside garnish.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the back door name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Using a heat light, heat the back door outside garnish and a new back door name plate.


iii.

Align the back door name plate boss positions and the back door outside garnish positioning rib, and install the back door name plate.

NOTICE:

The application strength of the back door name plate will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the back door outside garnish.




Hide 75473B 4.INSTALL REAR BODY NO. 3 NAME PLATE

Z101186

NOTICE:

When installing a new rear body No. 3 name plate, heat the back door panel and rear body No. 3 name plate using a heat light.



Standard Value:
Part Temperature
Back Door Panel 40 to 60°C (104 to 140°F)
Rear Body No. 3 Name Plate 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the back door panel and rear body No. 3 name plate excessively.


a.
B610499N01
0.719,0.26 1,0.615 0.281,0.354 18 false i 0.719,1.417 1,1.771 0.281,0.354 18 false ii

i.

Clean the surface of the back door panel.

1. Using a heat light, heat the back door panel surface.

2. Remove any remaining double-sided tape from the back door panel.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear body No. 3 name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Using a heat light, heat the back door panel and a new rear body No. 3 name plate.



b.
B610500C01
0.469,0.49 0.385,0.74 0.385,0.74 0.219,0.74 true 0.833,2.667 0.75,2.167 0.75,2.167 0.583,2.167 true 2.896,0.448 2.813,0.698 2.813,0.698 2.646,0.698 true 5.135,0.458 5.052,0.708 5.052,0.708 4.885,0.708 true 5.552,2.667 5.469,2.167 5.469,2.167 5.302,2.167 true 3.26,2.667 3.177,2.167 3.177,2.167 3.01,2.167 true 1.375,3.344 1.292,3.594 1.292,3.594 1.125,3.594 true 3.927,3.354 3.844,3.604 3.844,3.604 3.677,3.604 true 4.51,5.542 4.427,5.042 4.427,5.042 4.26,5.042 true 1.792,5.542 1.708,5.042 1.708,5.042 1.542,5.042 true 4.198,1.615 4.448,1.615 true 1.833,1.625 2.083,1.625 true 6.583,1.625 6.75,1.625 true 5.5,4.531 5.833,4.531 true 2.854,4.531 3.104,4.531 true 0.042,0.073 0.24,0.26 0.198,0.188 10 true *a 0.573,0.063 0.792,0.313 0.219,0.25 18 true i 0.615,0.302 0.771,0.5 0.156,0.198 10 true A 2.104,0.271 2.26,0.469 0.156,0.198 10 true B 1.875,1.24 2.031,1.438 0.156,0.198 10 true C 5.833,1.604 5.99,1.802 0.156,0.198 10 true L 1.313,1.625 1.469,1.823 0.156,0.198 10 true D 1.531,3.198 1.688,3.396 0.156,0.198 10 true M 3.917,3.146 4.073,3.344 0.156,0.198 10 true Q 0.396,2.094 0.667,2.292 0.271,0.198 10 true *d 0.021,0.646 0.292,0.844 0.271,0.198 10 true *b 4.688,0.635 4.958,0.833 0.271,0.198 10 true *b 2.469,0.604 2.74,0.802 0.271,0.198 10 true *b 3.021,0.281 3.177,0.479 0.156,0.198 10 true E 4.458,0.271 4.615,0.469 0.156,0.198 10 true F 4.281,1.25 4.438,1.448 0.156,0.198 10 true G 3.5,1.615 3.656,1.813 0.156,0.198 10 true H 5.375,0.313 5.531,0.51 0.156,0.198 10 true I 5.083,2.073 5.354,2.271 0.271,0.198 10 true *d 2.813,2.052 3.083,2.25 0.271,0.198 10 true *d 6.823,0.26 6.979,0.458 0.156,0.198 10 true J 6.615,1.229 6.771,1.427 0.156,0.198 10 true K 3.469,3.521 3.688,3.719 0.219,0.198 10 true *b 0.99,3.49 1.198,3.698 0.208,0.208 10 true *b 2.135,4.49 2.292,4.688 0.156,0.198 10 true P 2.854,3.125 3.01,3.323 0.156,0.198 10 true N 2.948,4.094 3.104,4.292 0.156,0.198 10 true O 4,4.948 4.271,5.146 0.271,0.198 10 true *d 1.313,4.958 1.583,5.156 0.271,0.198 10 true *d 5.49,3.104 5.646,3.302 0.156,0.198 10 true R 5.573,4.125 5.729,4.323 0.156,0.198 10 true S 4.75,4.469 4.906,4.667 0.156,0.198 10 true T 4.51,1.51 4.781,1.708 0.271,0.198 10 true *c 2.156,1.531 2.427,1.729 0.271,0.198 10 true *c 6.833,1.51 7.104,1.708 0.271,0.198 10 true *c 3.188,4.438 3.458,4.635 0.271,0.198 10 true *c 5.906,4.448 6.177,4.646 0.271,0.198 10 true *c
*a Reference Values *b Back Door Outside Garnish Edge
*c Back Door Panel Edge (Right Side) *d Back Door Panel Edge (Lower Side)


Standard Measurement:
Area Measurement Area Measurement
A 26.8 mm (1.06 in.) B 26.3 mm (1.04 in.)
C 32.4 mm (1.28 in.) D 293.6 mm (11.6 in.)
E 25.2 mm (0.992 in.) F 24.8 mm (0.976 in.)
G 30.5 mm (1.20 in.) H 293.6 mm (11.6 in.)
I 26.8 mm (1.06 in.) J 26.3 mm (1.04 in.)
K 32.4 mm (1.28 in.) L 293.7 mm (11.6 in.)
M 26.9 mm (1.06 in.) N 25.8 mm (1.02 in.)
O 31.7 mm (1.25 in.) P 293.6 mm (11.6 in.)
Q 27.1 mm (1.07 in.) R 25.8 mm (1.02 in.)
S 31.7 mm (1.25 in.) T 293.5 mm (11.6 in.)


i.

Align the cutout of the application sheet with the back door panel edge (right side) and install the rear body No. 3 name plate at the position shown in the illustration.

NOTICE:

The application strength of the rear body No. 3 name plate will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the back door panel.