| ● | Non-reusable part | - | - |
Use the same procedure for the RH and LH sides.
The procedure described below is for the LH side.
Use the same procedure for RHD and LHD vehicles.
The procedures listed below are for LHD vehicles.
67496C 1.INSTALL FRONT DOOR FRONT LOWER FRAME UPPER COVER LH
|
|
| Part | Temperature |
|---|---|
| Front Door Panel LH | 40 to 60°C (104 to 140°F) |
| Front Door Front Lower Frame Upper Cover LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the front door panel LH and front door front lower frame upper cover LH excessively.
| *a | Double-sided Tape | - | - |
Clean the surface of the front door panel LH.
1. Using a heat light, heat the front door panel LH surface.
2. Remove any remaining double-sided tape from the front door panel LH.
3. Wipe off any tape adhesive residue with cleaner.
Installing the front door front lower frame upper cover LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Clean a new front door panel LH surface.
Using a heat light, heat the front door panel LH and a new front door front lower frame upper cover LH.
Attach the clip and double-sided tape and install the front door front lower frame upper cover LH.
The application strength of the front door front lower frame upper cover LH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.
Apply pressure so that it does not lift up from the front door panel LH.
75754A 2.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING LH
Temporarily install the front door upper window frame moulding LH to the front door panel LH.
Install the No. 4 nose piece to an air riveter and insert the mandrel section of a new φ 4 mm rivet into the nose piece.
Press the rivets perpendicularly to the installation holes. Using the air riveter, install the front door upper window frame moulding LH with the 7 rivets.
When installing the rivets to the panel surface, do not tilt the riveter.
Do not leave a gap between the rivet head portion and the panel.
Pull the trigger again to cut off the rivet if it is not cut off.
67864H 3.INSTALL FRONT DOOR NO. 2 WEATHERSTRIP
75756C 4.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING LH
|
|
| Part | Temperature |
|---|---|
| Front Door Panel LH | 40 to 60°C (104 to 140°F) |
| Front Door Rear Window Frame Moulding LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the front door panel LH and front door rear window frame moulding LH excessively.
| *a | Double-sided Tape | - | - |
Clean the surface of the front door panel LH.
1. Using a heat light, heat the front door panel LH surface.
2. Remove any remaining double-sided tape from the front door panel LH.
3. Wipe off any tape adhesive residue with cleaner.
Installing the front door rear window frame moulding LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Clean a new front door panel LH surface.
Using a heat light, heat the front door panel LH and a new front door rear window frame moulding LH.
Attach the guide, clip and double-sided tape and install the front door rear window frame moulding LH.
The application strength of the front door rear window frame moulding LH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.
Apply pressure so that it does not lift up from the front door panel LH.
75720 5.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH