Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR WINDOW FRAME MOULDING
RM38G0E _59 Vehicle Exterior _100846 EXTERIOR PANELS / TRIM _0468078 REAR DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR WINDOW FRAME MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B610814N01
1.833,0.51 2.167,0.51 2.167,0.51 2.167,0.677 false 3.26,2.323 2.844,2.323 2.844,2.323 2.844,1.656 false 2.833,0.427 2.917,0.427 2.917,0.427 2.917,0.771 false 5.354,0.313 5.688,0.313 false 5.104,1.469 5.688,1.469 false 4.844,0.25 5.01,0.25 5.01,0.25 5.01,0.75 false 4.969,2.677 5.552,2.677 false 3.427,2.177 3.979,2.531 0.552,0.354 18 false 1 6.052,1.313 6.604,1.667 0.552,0.354 18 false 3 2.667,0.302 3.219,0.656 0.552,0.354 18 false 4 4.667,0.125 5.219,0.479 0.552,0.354 18 false 5 5.802,2.552 6.354,2.906 0.552,0.354 18 false 2 2.094,0.76 2.552,0.958 0.458,0.198 10 false x 4 5.406,0.323 5.865,0.521 0.458,0.198 10 false x 6 1.698,0.417 2.156,0.615 0.458,0.198 10 false ● 5.74,0.219 6.198,0.417 0.458,0.198 10 false ● 3.323,2.219 3.781,2.417 0.458,0.198 10 false ● 5.927,1.354 6.385,1.552 0.458,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR DOOR BELT MOULDING ASSEMBLY LH 75740 - - -
2 REAR NO. 4 DOOR WEATHERSTRIP 67898G (Click here) - -
3 REAR DOOR FRONT WINDOW FRAME MOULDING LH 75762A (Click here) - -
4 REAR DOOR REAR WINDOW FRAME MOULDING LH 75766A (Click here) - -
5 REAR DOOR UPPER WINDOW FRAME MOULDING LH 75764A (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear door front window frame moulding, rear door rear window frame moulding and rear door upper window frame moulding removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
·

Rear door glass sub-assembly LH

·

Rear door glass sub-assembly RH

·

Rear door glass run LH

·

Rear door glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 75740 1.REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

Hide 67898G 2.REMOVE REAR NO. 4 DOOR WEATHERSTRIP

Z101186

Click here(Click here)

Hide 75762A 3.REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH

Z101186

NOTICE:

When removing the rear door front window frame moulding LH, if the double-sided tape is difficult to remove, heat the adhesive of the rear door front window frame moulding LH using a heat light.



Standard Value:
Part Temperature
Rear Door Front Window Frame Moulding LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear door front window frame moulding LH excessively.


a.
B610815C01
3.083,1.083 3.333,1.083 true 3,1.25 3.25,1.25 3.25,1.25 3.25,1.083 true 2.146,0.927 2.427,1.281 0.281,0.354 18 false i 3.646,0.104 3.927,0.458 0.281,0.354 18 false ii 2.167,0 2.448,0.354 0.281,0.354 18 false iii 2.135,0.521 2.417,0.875 0.281,0.354 18 false iv 2.792,1.177 3.073,1.531 0.281,0.354 18 false v 3.365,1.01 3.677,1.167 0.313,0.156 10 false *a
*a Double-sided Tape - -
V113147

Remove in this Direction - -


i.

Put protective tape around the rear door front window frame moulding LH.


ii.

Heat the adhesive of the rear door front window frame moulding LH using a heat light.


iii.

Using a clip remover with its tip wrapped with protective tape, detach the clip as shown in the illustration.


iv.

Using scraper, detach the double-sided tape as shown in the illustration.


v.

Detach the guide and remove the rear door front window frame moulding LH.



Hide 75766A 4.REMOVE REAR DOOR REAR WINDOW FRAME MOULDING LH

a.
B610816C01
5.99,1.219 6.24,1.135 6.24,1.135 6.406,1.135 false 1.083,0.99 0.917,0.99 0.917,0.99 0.667,0.656 false 3.344,0.938 3.625,1.292 0.281,0.354 18 false i 0.615,0.031 1.583,0.385 0.969,0.354 18 false ii, iii 4.865,0.99 5.146,1.344 0.281,0.354 18 false iv 3.771,0.51 4.052,0.833 0.281,0.323 18 false v 1.135,0.906 1.448,1.104 0.313,0.198 10 false *a 6.448,1.052 6.76,1.25 0.313,0.198 10 false *b 0.5,1.063 0.656,1.26 0.156,0.198 10 false A
*a Tape *b Flange


i.

Put protective tape around the rear door rear window frame moulding LH.


ii.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


iii.

Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:
Area Measurement Area Measurement
A 5.0 mm (0.197 in.) - -


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



iv.

Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 4 rivets.

CAUTION:

Be careful of the drilled rivets, as they may be hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Prying the rivets with the drill may damage the rivet installation holes or drill bit.




v.

Remove the rear door rear window frame moulding LH.



Hide 75764A 5.REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING LH

a.
B610817C01
1.479,0.677 1.729,1.01 1.729,1.01 1.896,1.01 false 6.167,0.979 6.333,0.813 6.333,0.813 6.5,0.813 false 0.49,1.01 0.771,1.365 0.281,0.354 18 false i 1.448,0.052 2.417,0.458 0.969,0.406 18 false ii, iii 5.146,0.667 5.427,1.021 0.281,0.354 18 false iv 5.938,1.573 6.219,1.927 0.281,0.354 18 false v 1.958,0.917 2.271,1.115 0.313,0.198 10 false *a 6.552,0.729 6.865,0.927 0.313,0.198 10 false *b 1.323,1.104 1.479,1.302 0.156,0.198 10 false A
*a Tape *b Flange


i.

Put protective tape around the rear door upper window frame moulding LH.


ii.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


iii.

Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:
Area Measurement Area Measurement
A 5.0 mm (0.197 in.) - -


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



iv.

Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 6 rivets.

CAUTION:

Be careful of the drilled rivets, as they may be hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Prying the rivets with the drill may damage the rivet installation holes or drill bit.




v.

Remove the rear door upper window frame moulding LH.