Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › GRILLE SHUTTER
RM38G0E _59 Vehicle Exterior _100846 EXTERIOR PANELS / TRIM _0468084 GRILLE SHUTTER A

EXTERIOR PANELS / TRIM  GRILLE SHUTTER  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
B599950N03
5.719,1.292 5.802,1.125 5.802,1.125 5.969,1.125 false 4.448,0.531 4.531,0.365 4.531,0.365 4.698,0.365 false 4.5,1.031 4.781,1.031 4.781,1.031 4.865,1.198 false 5.146,2.01 5.229,1.844 5.229,1.844 5.396,1.844 false 1.615,3.938 1.854,3.938 1.854,3.938 1.938,3.771 false 1.729,3.135 1.833,2.917 1.833,2.917 2,2.917 false 1.115,1.865 1.198,1.698 1.198,1.698 1.365,1.698 false 1.354,2.969 1.583,2.5 1.583,2.5 1.75,2.5 false 2.49,4.594 2.969,4.594 2.969,4.594 3.052,4.427 false 2.948,3.906 3.229,3.906 3.229,3.906 3.313,4.073 false 3.719,3.406 3.969,3.406 3.969,3.406 4.052,3.573 false 3.604,4.302 3.771,4.635 3.771,4.635 4.188,4.635 false 4.708,3.552 5.208,4.552 5.208,4.552 5.458,4.552 false 5.281,3.875 5.448,4.208 5.448,4.208 5.833,4.208 false 5.469,1.76 5.781,1.958 0.313,0.198 10 false *1 1.708,1.552 1.865,1.75 0.156,0.198 10 false ● 2.073,2.396 2.229,2.594 0.156,0.198 10 false ● 2.281,2.813 2.438,3.01 0.156,0.198 10 false ● 1.25,3.844 1.406,4.042 0.156,0.198 10 false ● 2.135,4.51 2.292,4.708 0.156,0.198 10 false ● 2.625,3.781 2.781,3.979 0.156,0.198 10 false ● 3.354,3.313 3.51,3.51 0.156,0.198 10 false ● 4.49,4.531 4.646,4.729 0.156,0.198 10 false ● 5.74,4.438 5.896,4.635 0.156,0.198 10 false ● 6.125,4.104 6.281,4.302 0.156,0.198 10 false ● 4.188,0.927 4.344,1.125 0.156,0.198 10 false ● 5,0.271 5.156,0.469 0.156,0.198 10 false ● 6.24,1.021 6.396,1.219 0.156,0.198 10 false ● 5.156,0.24 5.438,0.5 0.281,0.26 18 false 2 6.385,0.99 6.667,1.344 0.281,0.354 18 false 3 1.854,1.521 2.135,1.875 0.281,0.354 18 false 4 3.521,3.271 3.813,3.5 0.292,0.229 18 false 4 2.417,2.781 2.698,3.135 0.281,0.354 18 false 5 2.75,3.75 3.031,4.104 0.281,0.354 18 false 5 6.26,4.063 6.542,4.417 0.281,0.354 18 false 6 1.417,3.802 1.698,4.156 0.281,0.354 18 false 7 2.219,2.385 2.479,2.677 0.26,0.292 18 false 8 4.302,0.906 4.635,1.177 0.333,0.271 18 false 1 4.656,4.49 4.917,4.781 0.26,0.292 18 false 8 2.281,4.479 2.594,4.75 0.313,0.271 18 false 7 5.875,4.417 6.156,4.771 0.281,0.354 18 false 6

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 7 RADIATOR GRILLE SEAL 53159G (Click here) - -
2 NO. 1 RADIATOR GRILLE SEAL 53155D (Click here) - -
3 NO. 2 RADIATOR GRILLE SEAL 53156E (Click here) - -
4 NO. 3 RADIATOR GRILLE SEAL 53157A (Click here) - -
5 NO. 5 RADIATOR GRILLE SEAL 53159K (Click here) - -
6 NO. 8 RADIATOR GRILLE SEAL 53157D (Click here) - -
7 NO. 6 RADIATOR GRILLE SEAL 53159F (Click here) - -
8 NO. 4 RADIATOR GRILLE SEAL 53158F (Click here) - -

*1 RADIATOR SHUTTER - -
● Non-reusable part - -

PROCEDURE

Hide 53159G 1.INSTALL NO. 7 RADIATOR GRILLE SEAL

Z101186

NOTICE:

When installing the No. 7 radiator grille seal, heat the No. 7 radiator grille seal and radiator shutter using a heat light.



Standard Value:
Part Temperature
Radiator Shutter 20 to 30°C (68 to 86°F)
No. 7 Radiator Grille Seal


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the No. 7 radiator grille seal and radiator shutter excessively.


a.
B599959C01
5.094,2.042 5.094,1.583 true 4.844,0.969 4.844,1.229 true 4.594,1.208 4.417,0.76 true 6.531,1.208 6.719,0.573 true 5,2.052 5.219,2.24 0.219,0.188 10 true *a 5.396,0.365 5.688,0.542 0.292,0.177 10 true A*c 5.604,0.958 5.927,1.146 0.323,0.188 10 false B*c 4.75,0.823 4.969,1.01 0.219,0.188 10 true *b 4.292,0.552 4.51,0.74 0.219,0.188 10 true *d 6.656,0.354 6.875,0.542 0.219,0.188 10 true *d 0.365,1.604 0.646,1.958 0.281,0.354 18 false i 2.052,1.604 2.333,1.958 0.281,0.354 18 false ii 4.167,0.073 4.448,0.427 0.281,0.354 18 false iii
*a Mark-off Line *b Standard of Seal Attachment
*c Range of Seal Attachment *d Edge of Curved Surface


Standard Measurement
Area Dimensions Area Dimensions
A 63.7 mm (2.51 in.) B 11 mm (0.433 in.)

i.

Clean the radiator shutter surface.

1. When reusing the radiator shutter, remove remaining double-sided tape from the radiator shutter.

2. Using a heat light, heat the radiator shutter surface.

3. Remove any remaining double-sided tape from the radiator shutter and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the No. 7 radiator grille seal with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new radiator shutter surface.




ii.

Using a heat light, heat the radiator shutter and a new No. 7 radiator grille seal.


iii.

Install the No. 7 radiator grille seal in the position shown in the illustration.

NOTICE:

The application strength of the No. 7 radiator grille seal will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the radiator shutter.




Hide 53155D 2.INSTALL NO. 1 RADIATOR GRILLE SEAL

Z101186

NOTICE:

When installing the No. 1 radiator grille seal, heat the No. 1 radiator grille seal and radiator shutter using a heat light.



Standard Value:
Part Temperature
Radiator Shutter 20 to 30°C (68 to 86°F)
No. 1 Radiator Grille Seal


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the No. 1 radiator grille seal and radiator shutter excessively.


a.
B599960C01
2.698,1.865 2.698,2.156 true 1.438,1.521 1.823,2.094 true 1.844,2.125 2.063,2.333 0.219,0.208 10 true *b 2.615,2.177 2.792,2.385 0.177,0.208 10 true *a 1.427,0.417 1.75,0.604 0.323,0.188 10 true A*d 2.542,1.094 2.833,1.281 0.292,0.188 10 true B*c 3.667,0.073 3.948,0.427 0.281,0.354 18 false i 5.344,0.083 5.625,0.438 0.281,0.354 18 false ii 0.396,0.083 0.677,0.438 0.281,0.354 18 false iii
*a Mark-off Line *b Standard of Seal Attachment
*c Range of Seal Attachment *d Attachment Error


Standard Measurement
Area Dimensions Area Dimensions
A Below 3 mm (0.118 in.) B 16 mm (0.630 in.)

i.

Clean the radiator shutter surface.

1. When reusing the radiator shutter, remove remaining double-sided tape from the radiator shutter.

2. Using a heat light, heat the radiator shutter surface.

3. Remove any remaining double-sided tape from the radiator shutter and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the No. 1 radiator grille seal with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new radiator shutter surface.




ii.

Using a heat light, heat the radiator shutter and a new No. 1 radiator grille seal.


iii.

Install the No. 1 radiator grille seal in the position shown in the illustration.

NOTICE:

The application strength of the No. 1 radiator grille seal will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the radiator shutter.




Hide 53156E 3.INSTALL NO. 2 RADIATOR GRILLE SEAL

Z101186

NOTICE:

When installing the No. 2 radiator grille seal, heat the No. 2 radiator grille seal and radiator shutter using a heat light.



Standard Value:
Part Temperature
Radiator Shutter 20 to 30°C (68 to 86°F)
No. 2 Radiator Grille Seal


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the No. 2 radiator grille seal and radiator shutter excessively.


a.
B599961C01
6,2.323 5.688,1.76 true 5.208,1.333 4.604,0.833 true 0.365,1.646 0.646,2 0.281,0.354 18 false i 2.052,1.646 2.333,2 0.281,0.354 18 false ii 4.146,0.083 4.427,0.438 0.281,0.354 18 false iii 4.365,0.646 4.833,0.844 0.469,0.198 10 true *a, *b 5.938,2.375 6.135,2.552 0.198,0.177 10 true *a 6.406,0.76 6.76,0.948 0.354,0.188 10 true B*c 5.188,0.375 5.552,0.573 0.365,0.198 10 true A*d
*a Mark-off Line *b Standard of Seal Attachment
*c Range of Seal Attachment *d Attachment Error


Standard Measurement
Area Dimensions Area Dimensions
A Below 3 mm (0.118 in.) B 16 mm (0.630 in.)

i.

Clean the radiator shutter surface.

1. When reusing the radiator shutter, remove remaining double-sided tape from the radiator shutter.

2. Using a heat light, heat the radiator shutter surface.

3. Remove any remaining double-sided tape from the radiator shutter and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the No. 2 radiator grille seal with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new radiator shutter surface.




ii.

Using a heat light, heat the radiator shutter and a new No. 2 radiator grille seal.


iii.

Install the No. 2 radiator grille seal in the position shown in the illustration.

NOTICE:

The application strength of the No. 2 radiator grille seal will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the radiator shutter.




Hide 53157A 4.INSTALL NO. 3 RADIATOR GRILLE SEAL

Z101186

NOTICE:

When installing the No. 3 radiator grille seal, heat the No. 3 radiator grille seal and radiator shutter using a heat light.



Standard Value:
Part Temperature
Radiator Shutter 20 to 30°C (68 to 86°F)
No. 3 Radiator Grille Seal


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the No. 3 radiator grille seal and radiator shutter excessively.


a.
B599962C01
1.635,1.906 2,1.906 true 5.25,1.927 5.615,1.927 true 2.396,1.531 2.698,1.708 true 4.5,1.708 4.854,1.531 true 2.75,1.625 2.948,1.823 0.198,0.198 10 true *b 1.438,1.802 1.635,2 0.198,0.198 10 true *a 1.458,1.5 1.792,1.708 0.333,0.208 10 false A*d 1.698,2.406 2.031,2.615 0.333,0.208 10 false B*c 5.594,1.5 5.927,1.708 0.333,0.208 10 false A*d 0.385,0.073 0.667,0.427 0.281,0.354 18 false i 6.229,0.094 6.396,0.375 0.167,0.281 18 true i 0.396,1.354 0.563,1.635 0.167,0.281 18 true ii 6.198,1.333 6.365,1.615 0.167,0.281 18 true ii 1.573,1.146 1.958,1.417 0.385,0.271 18 false iii 3.906,1.188 4.177,1.438 0.271,0.25 18 true iii 5.656,1.833 5.854,2.031 0.198,0.198 10 true *a 4.302,1.615 4.5,1.813 0.198,0.198 10 true *b 5.344,2.406 5.677,2.615 0.333,0.208 10 false B*c
*a Mark-off Line *b Standard of Seal Attachment
*c Range of Seal Attachment *d Attachment Error


Standard Measurement
Area Dimensions Area Dimensions
A Below 3 mm (0.118 in.) B 21 mm (0.827 in.)

i.

Clean the radiator shutter surface.

1. When reusing the radiator shutter, remove remaining double-sided tape from the radiator shutter.

2. Using a heat light, heat the radiator shutter surface.

3. Remove any remaining double-sided tape from the radiator shutter and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the No. 3 radiator grille seal with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new radiator shutter surface.




ii.

Using a heat light, heat the radiator shutter and a new No. 3 radiator grille seal.


iii.

Install the 2 No. 3 radiator grille seals in the position shown in the illustration.

NOTICE:

The application strength of the No. 3 radiator grille seal will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the radiator shutter.




Hide 53159K 5.INSTALL NO. 5 RADIATOR GRILLE SEAL

Z101186

NOTICE:

When installing the No. 5 radiator grille seal, heat the No. 5 radiator grille seal and radiator shutter using a heat light.



Standard Value:
Part Temperature
Radiator Shutter 20 to 30°C (68 to 86°F)
No. 5 Radiator Grille Seal


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the No. 5 radiator grille seal and radiator shutter excessively.


a.
B599963C01
1.979,2.167 2.313,1.99 true 5.135,2.156 4.885,2 true 2.729,1.646 3.073,1.771 true 4.458,1.646 4.104,1.792 true 0.375,0.115 0.51,0.365 0.135,0.25 18 true i 6.208,0.104 6.344,0.354 0.135,0.25 18 true i 0.354,1.354 0.531,1.615 0.177,0.26 18 true ii 6.198,1.354 6.375,1.615 0.177,0.26 18 true ii 2.052,1.302 2.333,1.563 0.281,0.26 18 false iii 3.917,1.302 4.135,1.563 0.219,0.26 18 false iii 1.781,2.125 1.969,2.323 0.188,0.198 10 false *a 5.177,2.115 5.365,2.313 0.188,0.198 10 false *a 3.115,1.688 3.302,1.885 0.188,0.198 10 true *b 3.896,1.698 4.083,1.896 0.188,0.198 10 true *b 2.344,1.396 2.75,1.573 0.406,0.177 10 false A*d 4.677,2.406 4.979,2.604 0.302,0.198 10 true B*c 4.917,1.396 5.302,1.583 0.385,0.188 10 false A*d 2.167,2.427 2.469,2.625 0.302,0.198 10 true B*c
*a Mark-off Line *b Standard of Seal Attachment
*c Range of Seal Attachment *d Attachment Error


Standard Measurement
Area Dimensions Area Dimensions
A Below 3 mm (0.118 in.) B 21 mm (0.827 in.)

i.

Clean the radiator shutter surface.

1. When reusing the radiator shutter, remove remaining double-sided tape from the radiator shutter.

2. Using a heat light, heat the radiator shutter surface.

3. Remove any remaining double-sided tape from the radiator shutter and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the No. 5 radiator grille seal with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new radiator shutter surface.




ii.

Using a heat light, heat the radiator shutter and a new No. 5 radiator grille seal.


iii.

Install the 2 No. 5 radiator grille seals in the position shown in the illustration.

NOTICE:

The application strength of the No. 5 radiator grille seal will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the radiator shutter.




Hide 53157D 6.INSTALL NO. 8 RADIATOR GRILLE SEAL

Z101186

NOTICE:

When installing the No. 8 radiator grille seal, heat the No. 8 radiator grille seal and radiator shutter using a heat light.



Standard Value:
Part Temperature
Radiator Shutter 20 to 30°C (68 to 86°F)
No. 8 Radiator Grille Seal


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the No. 8 radiator grille seal and radiator shutter excessively.


a.
B599964C01
2.656,2.094 2.427,1.74 true 5.917,2.104 5.688,1.75 true 3.625,1.51 3.427,1.75 true 6.885,1.51 6.688,1.75 true 0.375,0.135 0.531,0.396 0.156,0.26 18 false i 0.375,1.188 0.531,1.448 0.156,0.26 18 false ii 2.396,1.333 2.604,1.594 0.208,0.26 18 false iii 2.521,2.094 2.906,2.281 0.385,0.188 10 true *a *b 3.677,1.406 3.854,1.594 0.177,0.188 10 true *b 2.823,2.594 3.104,2.771 0.281,0.177 10 false A*c 3.115,1.927 3.396,2.104 0.281,0.177 10 true B*c 5.771,2.104 6.156,2.292 0.385,0.188 10 true *a *b 6.906,1.396 7.083,1.583 0.177,0.188 10 false *b 6.073,2.594 6.354,2.771 0.281,0.177 10 false A*c 6.365,1.917 6.646,2.094 0.281,0.177 10 true B*c
*a Mark-off Line *b Standard of Seal Attachment
*c Range of Seal Attachment - -


Standard Measurement
Area Dimensions Area Dimensions
A 60.5 mm (2.38 in.) B 14.6 mm (0.575 in.)

i.

Clean the radiator shutter surface.

1. When reusing the radiator shutter, remove remaining double-sided tape from the radiator shutter.

2. Using a heat light, heat the radiator shutter surface.

3. Remove any remaining double-sided tape from the radiator shutter and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the No. 8 radiator grille seal with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new radiator shutter surface.




ii.

Using a heat light, heat the radiator shutter and a new No. 8 radiator grille seal.


iii.

Install the 2 No. 8 radiator grille seals in the position shown in the illustration.

NOTICE:

The application strength of the No. 8 radiator grille seal will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the radiator shutter.




Hide 53159F 7.INSTALL NO. 6 RADIATOR GRILLE SEAL

Z101186

NOTICE:

When installing the No. 6 radiator grille seal, heat the No. 6 radiator grille seal and radiator shutter using a heat light.



Standard Value:
Part Temperature
Radiator Shutter 20 to 30°C (68 to 86°F)
No. 6 Radiator Grille Seal


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the No. 6 radiator grille seal and radiator shutter excessively.


a.
B599965C01
0.885,1.135 0.365,1.323 true 0.708,1.406 0.927,1.302 true 6.458,1.417 6.229,1.313 true 6.802,1.344 6.333,1.167 true 1.948,1.646 2.083,1.906 0.135,0.26 18 true ii 0.354,1.656 0.49,1.917 0.135,0.26 18 true i 4.073,1.646 4.208,1.906 0.135,0.26 18 true i 5.667,1.646 5.802,1.906 0.135,0.26 18 true ii 5.604,0.177 5.854,0.427 0.25,0.25 18 true iii 0.333,0.188 0.583,0.438 0.25,0.25 18 true iii 0.49,1.354 0.646,1.552 0.156,0.198 10 false *a 6.51,1.354 6.667,1.552 0.156,0.198 10 false *a 0.177,1.271 0.333,1.469 0.156,0.198 10 true *b 6.865,1.281 7.021,1.479 0.156,0.198 10 true *b 1.448,0.906 1.771,1.094 0.323,0.188 10 true A*c 0.656,0.51 0.979,0.719 0.323,0.208 10 true B*d 6.292,0.521 6.615,0.729 0.323,0.208 10 true B*d 5.458,0.896 5.781,1.083 0.323,0.188 10 true A*c
*a Mark-off Line *b Standard of Seal Attachment
*c Range of Seal Attachment *d Attachment Error


Standard Measurement
Area Dimensions Area Dimensions
A 13 mm (0.512 in.) B Below 3 mm (0.118 in.)

i.

Clean the radiator shutter surface.

1. When reusing the radiator shutter, remove remaining double-sided tape from the radiator shutter.

2. Using a heat light, heat the radiator shutter surface.

3. Remove any remaining double-sided tape from the radiator shutter and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the No. 6 radiator grille seal with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new radiator shutter surface.




ii.

Using a heat light, heat the radiator shutter and a new No. 6 radiator grille seal.


iii.

Install the 2 No. 6 radiator grille seals in the position shown in the illustration.

NOTICE:

The application strength of the No. 6 radiator grille seal will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the radiator shutter.




Hide 53158F 8.INSTALL NO. 4 RADIATOR GRILLE SEAL

Z101186

NOTICE:

When installing the No. 4 radiator grille seal, heat the No. 4 radiator grille seal and radiator shutter using a heat light.



Standard Value:
Part Temperature
Radiator Shutter 20 to 30°C (68 to 86°F)
No. 4 Radiator Grille Seal


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the No. 4 radiator grille seal and radiator shutter excessively.


a.
B599966C01
1.958,2.667 1.708,2.885 true 1.688,3.323 1.688,3.094 true 5.125,2.656 5.406,2.885 true 5.427,3.323 5.427,3.094 true 0.323,2.24 0.521,2.51 0.198,0.271 18 false iii 0.323,0.094 0.5,0.354 0.177,0.26 18 true i 1.979,2.469 2.177,2.656 0.198,0.188 10 true *b 1.615,3.333 1.802,3.542 0.188,0.208 10 false *a 1.854,3.542 2.188,3.74 0.333,0.198 10 false A*c 2.365,3.167 2.698,3.365 0.333,0.198 10 false B*c 5.76,0.083 5.938,0.344 0.177,0.26 18 true i 0.323,1.094 0.49,1.385 0.167,0.292 18 true ii 5.75,1.115 5.917,1.406 0.167,0.292 18 true ii 3.885,2.26 4.083,2.531 0.198,0.271 18 true iii 4.979,3.542 5.313,3.74 0.333,0.198 10 false A*c 4.573,3.188 4.906,3.385 0.333,0.198 10 false B*c 4.917,2.469 5.115,2.656 0.198,0.188 10 true *b 5.375,3.344 5.563,3.552 0.188,0.208 10 false *a
*a Mark-off Line *b Standard of Seal Attachment
*c Range of Seal Attachment - -


Standard Measurement
Area Dimensions Area Dimensions
A 100.6 mm (3.96 in.) B 13 mm (0.512 in.)

i.

Clean the radiator shutter surface.

1. When reusing the radiator shutter, remove remaining double-sided tape from the radiator shutter.

2. Using a heat light, heat the radiator shutter surface.

3. Remove any remaining double-sided tape from the radiator shutter and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the No. 4 radiator grille seal with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new radiator shutter surface.




ii.

Using a heat light, heat the radiator shutter and a new No. 4 radiator grille seal.


iii.

Install the 2 No. 4 radiator grille seals in the position shown in the illustration.

NOTICE:

The application strength of the No. 4 radiator grille seal will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the radiator shutter.