Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WHEEL OPENING MOULDING (for Front) › 2021.04–2021.07
RM38G0E _59 Vehicle Exterior _100846 EXTERIOR PANELS / TRIM _0468085 WHEEL OPENING MOULDING(for Front) A

EXTERIOR PANELS / TRIM  WHEEL OPENING MOULDING(for Front)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B623798N03
0.771,0.281 5.698,2.594 4.927,2.313 1.594,1.083 2.177,1.083 false 5.698,1.333 6.198,1.333 false 1.427,0.969 1.708,1.323 0.281,0.354 18 false 1 3.719,1.458 4.177,1.656 0.458,0.198 10 false x 2 3.406,2.354 3.865,2.552 0.458,0.198 10 false x 5 6.427,1.208 6.708,1.563 0.281,0.354 18 false 2 1.281,0.99 1.438,1.188 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT FENDER WHEEL ORNAMENT PAD - (Click here) - -
2 FRONT FENDER MOULDING SUB-ASSEMBLY LH 75602A (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT FENDER WHEEL ORNAMENT PAD

Z101186

NOTICE:

When installing the front fender wheel ornament pad, heat the front fender moulding sub-assembly LH and front fender wheel ornament pad using a heat light.



Standard Value:
Part Temperature
Front Fender Moulding Sub-assembly LH 20 to 30°C (68 to 86°F)
Front Fender Wheel Ornament Pad 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front fender moulding sub-assembly LH and front fender wheel ornament pad excessively.


a.
B623800C02
3.865,1.542 3.958,1.74 3.958,1.74 4.031,1.531 true 3.021,2.146 3.146,1.969 3.146,1.969 2.948,2 true 3.875,1.75 4.042,1.969 0.167,0.219 10 true *a 3.188,1.844 3.354,2.063 0.167,0.219 10 true *a 2.063,0.146 2.344,0.5 0.281,0.354 18 false i 1.302,1.479 1.583,1.833 0.281,0.354 18 false ii 3.208,1.333 3.49,1.688 0.281,0.354 18 false iii
*a Mark-off Line - -


i.

Clean the surface of the front fender moulding sub-assembly LH.

1. When reusing the front fender moulding sub-assembly LH, remove remaining double-sided tape from the front fender moulding sub-assembly LH.

2. Using a heat light, heat the front fender moulding sub-assembly LH surface.

3. Remove any remaining double-sided tape from the front fender moulding sub-assembly LH.

4. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the front fender wheel ornament pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Clean a new front fender moulding sub-assembly LH surface.




ii.

Using a heat light, heat the front fender moulding sub-assembly LH and a new front fender wheel ornament pad.


iii.

Install the front fender wheel ornament pad in the position shown in the illustration.

NOTICE:

The application strength of the front fender wheel ornament pad will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:
·

Make sure that the end of the front fender wheel ornament pad is between the mark-off lines.

·

Apply pressure so that it does not lift up from the front fender moulding sub-assembly LH.





Hide 75602A 2.INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY LH

Z101186

NOTICE:

When installing the front fender moulding sub-assembly LH, heat the front fender sub-assembly LH and front fender moulding sub-assembly LH using a heat light.



Standard Value:
Part Temperature
Front Fender Sub-assembly LH 40 to 60°C (104 to 140°F)
Front Fender Moulding Sub-assembly LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front fender sub-assembly LH and front fender moulding sub-assembly LH excessively.


a.
B617108C02
5.042,0.563 5.125,0.146 5.125,0.146 5.292,0.146 true 2.865,1.938 3.042,2.229 0.177,0.292 18 true v 6.24,0.188 6.448,0.479 0.208,0.292 18 false i 6.208,0.854 6.385,1.146 0.177,0.292 18 false ii 5.313,0.031 5.521,0.26 0.208,0.229 10 true *a 2.896,2.854 3.094,3.135 0.198,0.281 18 true iv 4.885,1.948 5.063,2.24 0.177,0.292 18 true v 3.5,0.563 3.688,0.823 0.188,0.26 18 true iii 2.563,3.26 2.76,3.542 0.198,0.281 18 true iv 3.896,2.844 4.094,3.125 0.198,0.281 18 true iv 4.729,3.073 4.927,3.354 0.198,0.281 18 true iv 4.927,3.406 5.125,3.688 0.198,0.281 18 true iv
*a Double-sided Tape - -
V100135

Screw
V100136

Clip


i.

Clean the surface of the front fender sub-assembly LH.

1. Using a heat light, heat the front fender sub-assembly LH surface.

2. Remove any remaining double-sided tape from the front fender sub-assembly LH.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the front fender moulding sub-assembly LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Using a heat light, heat the front fender sub-assembly LH and front fender moulding sub-assembly LH.


iii.

Attach the claw, clip and double-sided tape and install the front fender moulding sub-assembly LH.

NOTICE:

The application strength of the front fender moulding sub-assembly LH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the front fender sub-assembly LH.



iv.

Install the 5 clips.


v.

Using a 4 mm hexagon socket wrench, install the 2 screws.