Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR SPOILER
RM38G0E _59 Vehicle Exterior _100846 EXTERIOR PANELS / TRIM _0468087 REAR SPOILER A

EXTERIOR PANELS / TRIM  REAR SPOILER  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
B663257N02
2.052,4.5 5.385,5.583 3.333,1.083 2.833,4.927 3,4.927 3,4.927 3.083,5.094 false 3.917,5.052 3.917,5.333 false 5.042,4.875 5.042,5.156 false 2.615,3.5 2.615,3.667 2.615,3.667 6.354,3.521 false 3.5,3.313 3.5,3.313 3.5,3.313 3.5,3.646 false 5.01,2.896 5.01,3.573 false 4.229,2.844 4.229,3.604 false 5.854,2.625 5.854,3.542 false 1.917,3 1.917,2.75 1.917,2.75 5.333,2.417 false 2.521,3.01 1.583,3 false 0.667,0.594 0.833,0.594 0.833,0.594 0.833,1.427 false 1.917,0.594 1,0.594 1,0.594 1,1.094 false 1.604,0.583 1.604,1.25 false 2.635,0.156 3.417,0.156 3.417,0.156 3.417,0.406 false 3.104,0.833 2.771,0.833 2.771,0.833 2.771,0.167 false 3.219,1.365 2.802,1.365 2.802,1.365 2.802,1.198 false 4.51,0.344 3.844,0.344 3.844,0.344 3.844,0.667 false 1.25,0.604 1.25,0.604 1.25,0.604 1.25,0.854 false 3,0.167 3,0.167 3,0.167 3,0.583 false 5.396,5.021 5.729,5.021 false 5.531,4.01 5.948,4.01 false 6.479,0.542 6.813,0.542 false 2.667,4.833 2.979,5.031 0.313,0.198 10 false *1 3.854,5.271 4.135,5.625 0.281,0.354 18 false 8 4.979,5.104 5.26,5.458 0.281,0.354 18 false 9 4.458,4.917 4.917,5.115 0.458,0.198 10 false x 2 6.125,3.906 6.583,4.104 0.458,0.198 10 false ● 6.604,3.385 7.063,3.583 0.458,0.198 10 false ● 6.271,3.875 6.552,4.229 0.281,0.354 18 false 2 6.75,3.344 7.031,3.698 0.281,0.354 18 false 7 1.281,2.906 1.74,3.104 0.458,0.198 10 false ● 1.417,2.875 1.698,3.229 0.281,0.354 18 false 4 0.375,0.5 0.833,0.698 0.458,0.198 10 false ● 0.5,0.458 0.781,0.813 0.281,0.354 18 false 3 2.083,0.5 2.542,0.698 0.458,0.198 10 false ● 2.219,0.448 2.5,0.802 0.281,0.354 18 false 6 2.292,0.083 2.75,0.281 0.458,0.198 10 false ● 2.427,0.052 2.708,0.406 0.281,0.354 18 false 6 3.417,1.271 3.875,1.469 0.458,0.198 10 false ● 3.552,1.24 3.833,1.594 0.281,0.354 18 false 5 4.708,0.198 5.167,0.396 0.458,0.198 10 false ● 4.844,0.167 5.125,0.521 0.281,0.354 18 false 3 5.938,4.885 6.417,5.25 0.479,0.365 18 false 10 6.302,0.396 6.583,0.75 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 REAR SPOILER NO. 1 SEAL 76889F (Click here) - -
3 REAR SPOILER NO. 3 SIDE PROTECTOR 76888 (Click here) - -
4 REAR SPOILER NO. 2 SEAL 76887F (Click here) - -
5 REAR SPOILER NO. 3 PROTECTOR 76874C (Click here) - -
6 REAR SPOILER NO. 2 PROTECTOR 76873B (Click here) - -
7 REAR SPOILER NO. 1 PROTECTOR 76872A (Click here) - -
8 REAR WASHER NOZZLE 85345R - - -
9 NO. 1 WASHER BRACKET - - - -
10 REAR WASHER NOZZLE WITH HOSE ASSEMBLY - (Click here) - -

*1 WASHER HOSE - -
● Non-reusable part - -

PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

When installing the protector, seal heat the protector, seal, and rear spoiler using a heat light.



Standard Value:
Part Temperature
Rear Spoiler 20 to 30°C (68 to 86°F)
·

Protector

·

Seal


20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear spoiler, protector, seal excessively.


Hide 76889F 2.INSTALL REAR SPOILER NO. 1 SEAL

a.
B663264C02
3.5,2.083 3.583,1.75 true 0.552,0.115 0.781,0.396 0.229,0.281 18 false i 1.938,0.115 2.167,0.396 0.229,0.281 18 false ii 3.281,0.115 3.542,0.406 0.26,0.292 18 false iii 3.438,1.198 3.688,1.49 0.25,0.292 18 true iv 3.333,2.135 3.583,2.302 0.25,0.167 10 true *a
*a R End - -


i.

Clean the rear spoiler surface.

1. When reusing the rear spoiler, remove remaining double-sided tape from the rear spoiler.

2. Using a heat light, heat the rear spoiler surface.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear spoiler No. 1 seal with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Primer application.

1. Apply primer to the rear spoiler on the installation area of the rear spoiler No. 1 seal using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks.

·

Do not touch surfaces to which primer has been applied until the rear spoiler No. 1 seal has been attached.



2. Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



iii.

Using a heat light, heat the rear spoiler and a new rear spoiler No. 1 seal.


iv.

Install the rear spoiler No. 1 seal in the position shown in the illustration.

NOTICE:

The application strength of the rear spoiler No. 1 seal will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the rear spoiler.




Hide 76888 3.INSTALL REAR SPOILER NO. 3 SIDE PROTECTOR

a.
B663265C02
6.625,2.75 6.781,2.594 true 0.563,2.781 0.417,2.656 true 0.302,2.49 0.615,2.688 0.313,0.198 10 false *a 1.917,0.51 2.198,0.865 0.281,0.354 18 false i 3.479,0.521 3.771,0.917 0.292,0.396 18 false ii 5.01,0.51 5.292,0.865 0.281,0.354 18 false iii 0.479,4.021 0.76,4.375 0.281,0.354 18 false iv 6.781,2.458 7.094,2.656 0.313,0.198 10 false *a 6.74,4.01 7.135,4.948 0.396,0.938 18 false iv
*a Mark-off Line - -


i.

Clean the rear spoiler surface.

1. When reusing the rear spoiler, remove remaining double-sided tape from the rear spoiler.

2. Using a heat light, heat the rear spoiler surface.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear spoiler No. 3 side protector with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Primer application.

1. Apply primer to the rear spoiler on the installation area of the rear spoiler No. 3 side protector using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks.

·

Do not touch surfaces to which primer has been applied until the rear spoiler No. 3 side protector has been attached.



2. Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



iii.

Using a heat light, heat the rear spoiler and a new rear spoiler No. 3 side protector.


iv.

Install the 2 rear spoiler No. 3 side protectors in the position shown in the illustration.

NOTICE:

The application strength of the rear spoiler No. 3 side protector will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the rear spoiler.




Hide 76887F 4.INSTALL REAR SPOILER NO. 2 SEAL

a.
B663266C02
1.208,2.917 1.063,2.792 true 5.854,2.917 6.021,2.781 true 1.854,0.479 2.135,0.833 0.281,0.354 18 false i 3.438,0.479 3.719,0.833 0.281,0.354 18 false ii 4.938,0.479 5.219,0.833 0.281,0.354 18 false iii 0.552,4.052 0.833,4.406 0.281,0.354 18 false iv 6.948,4.042 7.135,4.406 0.188,0.365 18 false iv 0.927,2.552 1.135,2.76 0.208,0.208 10 true *a 6.083,2.583 6.292,2.792 0.208,0.208 10 true *a
*a Mark-off Line - -


i.

Clean the rear spoiler surface.

1. When reusing the rear spoiler, remove remaining double-sided tape from the rear spoiler.

2. Using a heat light, heat the rear spoiler surface.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear spoiler No. 2 seal with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Primer application.

1. Apply primer to the rear spoiler on the installation area of the rear spoiler No. 2 seal using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks.

·

Do not touch surfaces to which primer has been applied until the rear spoiler No. 2 seal has been attached.



2. Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



iii.

Using a heat light, heat the rear spoiler and a new rear spoiler No. 2 seal.


iv.

Install the 2 rear spoiler No. 2 seal in the position shown in the illustration.

NOTICE:

The application strength of the rear spoiler No. 2 seal will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the rear spoiler.




Hide 76874C 5.INSTALL REAR SPOILER NO. 3 PROTECTOR

a.
B663268C01
1.365,2.073 1.26,1.896 true 6,1.833 5.802,2.063 false 0.531,0.115 0.76,0.396 0.229,0.281 18 false i 1.927,0.115 2.156,0.396 0.229,0.281 18 false ii 3.25,0.115 3.51,0.406 0.26,0.292 18 false iii 6.052,1.688 6.229,1.875 0.177,0.188 10 true *a 1.167,1.719 1.344,1.906 0.177,0.188 10 true *a 3.5,2.094 3.75,2.385 0.25,0.292 18 false iv
*a Mark-off Line - -


i.

Clean the rear spoiler surface.

1. When reusing the rear spoiler, remove remaining double-sided tape from the rear spoiler.

2. Using a heat light, heat the rear spoiler surface.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear spoiler No. 3 protector with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Primer application.

1. Apply primer to the rear spoiler on the installation area of the rear spoiler No. 3 protector using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks.

·

Do not touch surfaces to which primer has been applied until the rear spoiler No. 3 protector has been attached.



2. Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



iii.

Using a heat light, heat the rear spoiler and a new rear spoiler No. 3 protector.


iv.

Install the rear spoiler No. 3 protector in the position shown in the illustration.

NOTICE:

The application strength of the rear spoiler No. 3 protector will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the rear spoiler.




Hide 76873B 6.INSTALL REAR SPOILER NO. 2 PROTECTOR

a.
B663267C03
0.615,2.313 0.781,2.594 true 5.865,5.021 5.792,4.865 true 4.448,2.677 4.375,2.521 true 3.104,2.656 3.25,2.51 true 1.24,5.021 1.167,4.833 true 6.479,2.458 6.396,2.708 true 1.833,0.313 2.063,0.594 0.229,0.281 18 false i 3.427,0.323 3.656,0.604 0.229,0.281 18 false ii 4.948,0.333 5.208,0.625 0.26,0.292 18 false iii 4.229,4.094 4.479,4.385 0.25,0.292 18 false iv 1.073,4.635 1.25,4.823 0.177,0.188 10 true *a 5.698,4.656 5.875,4.844 0.177,0.188 10 true *a 0.615,5.01 0.865,5.302 0.25,0.292 18 false iv 3.219,4.104 3.469,4.396 0.25,0.292 18 false iv 0.448,4.24 0.698,4.531 0.25,0.292 18 false iv 6.625,4.99 6.875,5.281 0.25,0.292 18 false iv 6.823,4.167 7.073,4.458 0.25,0.292 18 false iv 4.281,2.313 4.458,2.5 0.177,0.188 10 true *a 3.292,2.385 3.469,2.573 0.177,0.188 10 true *a 0.469,2.073 0.646,2.26 0.177,0.188 10 true *a 6.427,2.24 6.604,2.427 0.177,0.188 10 true *a
*a Mark-off Line - -


i.

Clean the rear spoiler surface.

1. When reusing the rear spoiler, remove remaining double-sided tape from the rear spoiler.

2. Using a heat light, heat the rear spoiler surface.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear spoiler No. 2 protector with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Primer application.

1. Apply primer to the rear spoiler on the installation area of the rear spoiler No. 2 protector using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks.

·

Do not touch surfaces to which primer has been applied until the rear spoiler No. 2 protector has been attached.



2. Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



iii.

Using a heat light, heat the rear spoiler and a new rear spoiler No. 2 protector.


iv.

Install the 6 rear spoiler No. 2 protectors in the position shown in the illustration.

NOTICE:

The application strength of the rear spoiler No. 2 protector will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the rear spoiler.




Hide 76872A 7.INSTALL REAR SPOILER NO. 1 PROTECTOR

a.
B663269C01
3.667,1.76 3.667,1.5 true 3.583,1.313 3.76,1.5 0.177,0.188 10 true *a 0.542,0.125 0.771,0.406 0.229,0.281 18 false i 1.938,0.125 2.167,0.406 0.229,0.281 18 false ii 3.26,0.125 3.521,0.417 0.26,0.292 18 false iii 0.813,3.229 1.063,3.521 0.25,0.292 18 true iv 2.26,3.417 2.51,3.708 0.25,0.292 18 true iv 3.458,3.458 3.708,3.75 0.25,0.292 18 true iv 6.104,3.302 6.354,3.594 0.25,0.292 18 true iv 4.771,3.448 5.021,3.74 0.25,0.292 18 true iv
*a Mark-off Line - -


i.

Clean the rear spoiler surface.

1. When reusing the rear spoiler, remove remaining double-sided tape from the rear spoiler.

2. Using a heat light, heat the rear spoiler surface.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear spoiler No. 1 protector with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Primer application.

1. Apply primer to the rear spoiler on the installation area of the rear spoiler No. 1 protector using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks.

·

Do not touch surfaces to which primer has been applied until the rear spoiler No. 1 protector has been attached.



2. Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



iii.

Using a heat light, heat the rear spoiler and a new rear spoiler No. 1 protector.


iv.

Install the 5 rear spoiler No. 1 protectors in the position shown in the illustration.

NOTICE:

The application strength of the rear spoiler No. 1 protector will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the rear spoiler.




Hide 85345R 8.INSTALL REAR WASHER NOZZLE

Hide 9.INSTALL NO. 1 WASHER BRACKET

Hide 10.INSTALL REAR WASHER NOZZLE WITH HOSE ASSEMBLY

Z101186

Click here(Click here)