| *A | for Standard | - | - |
| *1 | Rivet | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 8 | NO. 1 SIDE STEP BRACKET LH | 51794A | - | - | - |
| 9 | NO. 1 SIDE STEP STAY SUB-ASSEMBLY LH | 51082 | - | - | - |
| 10 | NO. 3 SIDE STEP BRACKET LH | 51798 | - | - | - |
| 11 | GROMMET SCREW | - | - | - | - |
| *A | for Full Cover Type | - | - |
Use the same procedure for the RH and LH sides.
The procedure described below is for the LH side.
51794A 1.REMOVE NO. 1 SIDE STEP BRACKET LH (for Standard)
51082 2.REMOVE NO. 1 SIDE STEP STAY SUB-ASSEMBLY LH (for Standard)
51798 3.REMOVE NO. 3 SIDE STEP BRACKET LH (for Standard)
51774A 4.REMOVE SIDE DOOR FRONT STEP PLATE COVER LH (for Standard)
|
Remove in this Direction | - | - |
51759A 5.REMOVE SIDE DOOR REAR STEP PLATE COVER LH (for Standard)
|
Remove in this Direction | - | - |
51792C 6.REMOVE REAR STEP PANEL LH (for Standard)
| *a | Tape | *b | Flange |
Insert a 4.0 mm (0.157 in.) drill bit into a drill.
Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.
| Area | Measurement |
|---|---|
| A | 5.0 mm (0.197 in.) |
Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.
Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 2 rivets and rear step panel LH.
Be careful of the drilled rivets, as they may be hot.
Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
Prying the rivets with the drill may damage the rivet installation holes or drill bit.
51785 7.REMOVE NO. 2 STEP BRACKET GUSSET (for Standard)
| *a | Tape | *b | Flange |
Insert a 4.0 mm (0.157 in.) drill bit into a drill.
Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.
| Area | Measurement |
|---|---|
| A | 5.0 mm (0.197 in.) |
Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.
Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 4 rivets and 2 No. 2 step bracket gussets.
Be careful of the drilled rivets, as they may be hot.
Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
Prying the rivets with the drill may damage the rivet installation holes or drill bit.
51794A 8.REMOVE NO. 1 SIDE STEP BRACKET LH (for Full Cover Type)
51082 9.REMOVE NO. 1 SIDE STEP STAY SUB-ASSEMBLY LH (for Full Cover Type)
51798 10.REMOVE NO. 3 SIDE STEP BRACKET LH (for Full Cover Type)
11.REMOVE GROMMET SCREW (for Full Cover Type)