Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF CARRIER
RM38G0E _59 Vehicle Exterior _100846 EXTERIOR PANELS / TRIM _0468093 ROOF CARRIER A

EXTERIOR PANELS / TRIM  ROOF CARRIER  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B599979N02
4.323,1.729 5.177,1.938 0.854,0.208 5.51,2.917 6.365,3.125 0.854,0.208 0.094,1.646 7.031,4.365 6.938,2.719 1.313,2.729 2.167,2.938 0.854,0.208 0.823,0.948 0.99,0.948 0.99,0.948 1.073,1.115 false 3.594,1.479 3.76,1.479 3.76,1.479 3.844,1.646 false 0.927,3.917 1.031,4.125 1.031,4.125 1.198,4.125 false 0.771,3.958 0.854,4.125 0.854,4.125 1.021,4.125 false 5.688,2.542 5.781,2.74 5.781,2.74 5.948,2.74 false 5.531,2.573 5.615,2.74 5.615,2.74 5.781,2.74 false 0.75,3.177 0.917,2.844 0.917,2.844 1.021,2.844 false 5.083,2.698 5.25,3.031 5.25,3.031 5.5,3.031 false 5.667,0.344 5.75,0.51 5.75,0.51 5.917,0.51 false 5.521,4.542 5.75,4.542 false 5.188,1.833 5.583,1.833 false 3.219,2.417 3.385,2.417 3.385,2.417 3.469,2.583 false 0.833,3.24 1.292,3.438 0.458,0.198 10 false x 2 5.76,1.833 6.219,2.031 0.458,0.198 10 false x 2 6.406,2.604 6.75,2.854 0.344,0.25 18 false 1 1.521,4.031 1.677,4.229 0.156,0.198 10 false ● 6.313,2.635 6.469,2.833 0.156,0.198 10 false ● 1.646,4 1.99,4.25 0.344,0.25 18 false 1 3.406,1.323 3.75,1.573 0.344,0.25 18 false 2 5.99,0.396 6.333,0.646 0.344,0.25 18 false 3 5.823,4.427 6.167,4.677 0.344,0.25 18 false 4 0.615,0.823 0.958,1.073 0.344,0.25 18 false 5 0.042,0.063 0.406,0.344 0.365,0.281 12 false *A 5.635,2.948 6.583,3.344 0.948,0.396 8 false 31 (316, 23) 1.448,2.76 2.917,2.917 1.469,0.156 8 false 39 (398, 29) 4.448,1.76 5.917,1.917 1.469,0.156 8 false 39 (398, 29) 3.031,2.333 3.49,2.531 0.458,0.198 10 false *1 1.073,2.75 1.427,2.948 0.354,0.198 10 false ●★ 4.073,1.74 4.427,1.938 0.354,0.198 10 false ●★

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 2 ROOF CARRIER SEAL 63437A (Click here) - -
2 ROOF CARRIER SUB-ASSEMBLY LH 63408C - - -
3 REAR ROOF RACK LEG COVER LH 63494 - - -
4 CENTER ROOF RACK LEG COVER LH 63496 - - -
5 FRONT ROOF RACK LEG COVER LH 63492 - - -

*A for Type A - -
*1 ROOF CARRIER LH - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
★ Precoated part - -

B616897N01
3.24,2.031 6.333,3.521 3.094,1.49 0.75,3.604 6.333,5.771 5.583,2.167 5.063,1.01 5.823,1.229 0.76,0.219 5.573,1.479 6.333,1.698 0.76,0.219 1.385,1.979 2.146,2.198 0.76,0.219 3.24,1.719 4,1.938 0.76,0.219 3.677,2.552 3.917,2.552 3.917,2.552 4.01,2.719 false 2.625,3.948 2.865,3.948 2.865,3.948 2.958,4.115 false 2.135,1.729 2.385,1.729 2.385,1.729 2.521,1.469 false 4.719,0.552 4.854,0.802 4.854,0.802 5.052,0.802 false 4.792,1.406 4.542,1.406 4.542,1.406 4.302,0.948 false 4.417,1.802 4.219,1.802 4.219,1.802 3.823,1.052 false 3.073,0.469 3.313,0.469 3.313,0.469 3.406,0.635 false 2.146,2.094 2.396,2.094 2.396,2.094 2.531,1.833 false 2.385,2.094 2.635,2.094 2.635,2.094 2.813,1.74 false 5.063,1.115 4.813,1.115 4.813,1.115 4.698,0.906 false 5.573,1.594 4.458,1.594 4.458,1.594 4.302,1.302 false 2.865,1.313 2.948,1.146 2.948,1.146 3.115,1.146 false 3.823,1.521 3.823,1.708 false 0.052,0.052 0.427,0.292 0.375,0.24 12 false *A 3.344,2.094 3.719,2.333 0.375,0.24 12 false *B 1.833,1.646 1.99,1.844 0.156,0.198 10 false ● 2.438,3.823 2.594,4.177 0.156,0.354 18 false 9 3.438,1.063 3.604,1.26 0.167,0.198 10 false ● 4.656,1.708 4.813,1.906 0.156,0.198 10 false ● 5.104,1.302 5.26,1.5 0.156,0.198 10 false ● 5.385,0.677 5.542,0.875 0.156,0.198 10 false ● 3.479,2.427 3.635,2.781 0.156,0.354 18 false 8 1.938,1.625 2.094,1.979 0.156,0.354 18 false 6 3.552,1.031 3.708,1.385 0.156,0.354 18 false 6 4.76,1.698 4.917,2.052 0.156,0.354 18 false 6 5.208,1.281 5.365,1.635 0.156,0.354 18 false 6 5.49,0.646 5.646,1 0.156,0.354 18 false 6 0.823,3.688 1.198,3.927 0.375,0.24 12 false *C 5.104,1.052 5.917,1.333 0.813,0.281 8 false 12.5 (127, 9) 5.625,1.51 6.438,1.792 0.813,0.281 8 false 12.5 (127, 9) 1.438,2.01 2.25,2.292 0.813,0.281 8 false 12.5 (127, 9) 3.313,1.76 4.125,2.042 0.813,0.281 8 false 12.5 (127, 9) 2.896,0.333 3.052,0.688 0.156,0.354 18 false 7

Procedure Part Name Code
Z101186

Z101188

Z101187

6 NO. 2 ROOF CARRIER SEAL 63437A (Click here) - -
7 ROOF RACK ASSEMBLY LH 63470B - - -
8 CURTAIN SHIELD AIRBAG ASSEMBLY LH 62180A - - -
9 ROOF HEADLINING ASSEMBLY - - - -

*A for Type B *B w/ Curtain Shield Airbag
*C w/o Curtain Shield Airbag - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 63437A 1.INSTALL NO. 2 ROOF CARRIER SEAL (for Type A)

Z101186

NOTICE:

When installing the No. 2 roof carrier seal, heat the No. 2 roof carrier seal and roof carrier LH using a heat light.



Standard Value:
Part Temperature
Roof Carrier LH 40 to 60°C (104 to 140°F)
No. 2 Roof Carrier Seal 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the No. 2 roof carrier seal and roof carrier LH excessively.


a.
B600085N04
0.615,0.229 0.896,0.583 0.281,0.354 18 false i 2.615,0.229 2.896,0.583 0.281,0.354 18 false ii 5.229,0.219 5.51,0.573 0.281,0.354 18 false iii

i.

Clean the roof carrier LH surface.

1. When reusing the roof carrier LH, remove remaining double-sided tape from the roof carrier LH.

2. Using a heat light, heat the roof carrier LH surface.

3. Remove any remaining double-sided tape from the roof carrier LH and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the No. 2 roof carrier seal with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new roof carrier LH surface.




ii.

Using a heat light, heat the roof carrier LH and a new No. 2 roof carrier seal.


iii.

Install the 4 No. 2 roof carrier seals in the position shown in the illustration.

NOTICE:

The application strength of the No. 2 roof carrier seal will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the roof carrier LH.




Hide 63408C 2.INSTALL ROOF CARRIER SUB-ASSEMBLY LH (for Type A)

a.
B600082C03
0.875,1.792 1.073,1.99 0.198,0.198 10 true *a 1.229,1.708 1.427,1.906 0.198,0.198 10 true *a 5.375,1.021 5.573,1.219 0.198,0.198 10 true *b 6.458,0.323 6.656,0.521 0.198,0.198 10 true *a 6.854,0.563 7.052,0.76 0.198,0.198 10 true *a
*a Bolt<A> *b Bolt<B>


Torque:
Bolt<A> : 39 N*m (398 kgf*cm, 29 ft.*lbf)
Bolt<B> : 31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 63494 3.INSTALL REAR ROOF RACK LEG COVER LH (for Type A)

Hide 63496 4.INSTALL CENTER ROOF RACK LEG COVER LH (for Type A)

Hide 63492 5.INSTALL FRONT ROOF RACK LEG COVER LH (for Type A)

Hide 63437A 6.INSTALL NO. 2 ROOF CARRIER SEAL (for Type B)

Z101186

NOTICE:

When installing the No. 2 roof carrier seal, heat the No. 2 roof carrier seal and roof rack assembly LH using a heat light.



Standard Value:
Part Temperature
roof rack assembly LH 40 to 60°C (104 to 140°F)
No. 2 Roof Carrier Seal 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the No. 2 roof carrier seal and roof rack assembly LH excessively.


a.
B600010N01
0.823,0.188 1.104,0.542 0.281,0.354 18 false i 3.021,0.167 3.302,0.521 0.281,0.354 18 false ii 5.156,0.177 5.438,0.531 0.281,0.354 18 false iii

i.

Clean the roof rack assembly LH surface.

1. When reusing the roof rack assembly LH, remove remaining double-sided tape from the roof rack assembly LH.

2. Using a heat light, heat the roof rack assembly LH surface.

3. Remove any remaining double-sided tape from the roof rack assembly LH and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the No. 2 roof carrier seal with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new roof rack assembly LH surface.




ii.

Using a heat light, heat the roof rack assembly LH and a new No. 2 roof carrier seal.


iii.

Install the 5 No. 2 roof carrier seals in the position shown in the illustration.

NOTICE:

The application strength of the No. 2 roof carrier seal will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the roof rack assembly LH.




Hide 63470B 7.INSTALL ROOF RACK ASSEMBLY LH (for Type B)

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

Hide 62180A 8.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH (for Type B, w/ Curtain Shield Airbag)

Hide 9.INSTALL ROOF HEADLINING ASSEMBLY (for Type B, w/o Curtain Shield Airbag)