| *1 | END FRAME | - | - |
| ● | Non-reusable part | - | - |
|
High temperature grease | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 11 | WINCH MOTOR WIRE | 38629 | - | - | - |
| 12 | STEPPED MALE WINCH MOTOR BUSHING | 38627 | - | - | - |
| 13 | STUD WINCH MOTOR BOLT | 38625 | - | - | - |
| 14 | WINCH MOTOR WIRE | 38639 | - | - | - |
| 15 | WINCH MOTOR MAGNET SWITCH | 38611B | - | - | - |
| 16 | WINCH MOTOR STOPPER | 38623 | - | - | - |
| 17 | WINCH MOTOR ASSEMBLY | 38610A | - | - | - |
| 18 | MAGNET SWITCH WINCH COVER | 38621B | - | - | - |
| *1 | CABLE TIE | *2 | WIRE |
| *3 | BRACKET A | *4 | BRACKET B |
| ● | Non-reusable part | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| *1 | WINCH BASE | *2 | FRONT BASE MEMBER |
| *3 | SNAP RING | - | - |
| ● | Non-reusable part | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
38613B 1.INSTALL WINCH MOTOR BRUSH SPRING
38603C 2.INSTALL NO. 2 WINCH MOTOR ARMATURE BEARING
Using a 19 mm socket wrench and press, press in a new No. 2 winch motor armature bearing.
38603B 3.INSTALL NO. 1 WINCH MOTOR ARMATURE BEARING
Using a 12 mm socket wrench and press, press in a new No. 1 winch motor armature bearing.
38603A 4.INSTALL WINCH MOTOR ARMATURE SUB-ASSEMBLY
| *a | End Frame | - | - |
|
Install in this Direction | - | - |
Apply high temperature grease to the inside of the end frame bushing.
Install the winch motor armature sub-assembly.
38601A 5.INSTALL WINCH MOTOR YOKE SUB-ASSEMBLY
Align the alignment marks and install the winch motor yoke sub-assembly to the end frame.
38604A 6.INSTALL WINCH MOTOR BRUSH HOLDER ASSEMBLY
Align the alignment marks and install the winch motor brush holder assembly to the winch motor brush holder assembly.
38613A 7.INSTALL WINCH MOTOR BRUSH
Install the winch motor brush with the screw.
Using a screwdriver, pry the winch motor brush spring forward and install the winch motor brush into the holder as shown in the illustration, and then remove the screwdriver from the spring.
Install the 3 remaining brushes using the same procedure.
38614A 8.INSTALL WINCH MOTOR O-RING
28199B 9.INSTALL DUST WINCH MOTOR PROTECTOR
38618 10.INSTALL WINCH MOTOR COMMUTATOR END FRAME
38629 11.INSTALL WINCH MOTOR WIRE
38627 12.INSTALL STEPPED MALE WINCH MOTOR BUSHING
38625 13.INSTALL STUD WINCH MOTOR BOLT
38639 14.INSTALL WINCH MOTOR WIRE
38611B 15.INSTALL WINCH MOTOR MAGNET SWITCH
38623 16.INSTALL WINCH MOTOR STOPPER
38610A 17.INSTALL WINCH MOTOR ASSEMBLY
38621B 18.INSTALL MAGNET SWITCH WINCH COVER
82295 19.INSTALL WINCH EARTH WIRE
38600A 20.INSTALL WINCH WITH MAGNET SWITCH MOTOR ASSEMBLY
| *a | Bolt A | *b | Bolt B |
| *c | Bolt C | *d | Bolt D |
Install the winch motor assembly with the 3 bolts.
Install the winch base with the 8 bolts.
38360 21.INSTALL WINCH ROLLER BRACKET ASSEMBLY
| *a | Bolt A | *b | Bolt B |
|
Snap Ring |
|
Bolt |
Install the winch roller bracket assembly with the 4 bolts, 2 washers and 2 nuts as shown in the illustration.
Install the member with the 4 bolts.
22.INSTALL WINCH HOOK
Using a snap ring expander, install the winch hook with a new snap ring.
38380 23.INSTALL WINCH HOOK HOLDER ASSEMBLY