Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR DRIVE UNIT
RM38G0E _59 Vehicle Exterior _100887 DOOR / HATCH _0468201 POWER BACK DOOR DRIVE UNIT A

DOOR / HATCH  POWER BACK DOOR DRIVE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B625747N02
4.344,1.104 4.677,1.104 false 3.969,2.083 4.302,2.083 false 4.396,0.521 4.729,0.521 false 6.063,0.833 6.396,0.833 false 3.667,3.083 4,3.083 false 4.865,2.396 5.198,2.396 false 4.01,0.542 4.25,0.25 4.25,0.25 4.417,0.25 false 3.5,2.958 3.781,3.313 0.281,0.354 18 false 1 6.469,0.708 6.75,1.063 0.281,0.354 18 false 3 4.792,0.365 5.073,0.719 0.281,0.354 18 false 4 3.792,1.927 4.073,2.281 0.281,0.354 18 false 5 5,1 5.281,1.354 0.281,0.354 18 false 2 4.469,0.167 4.781,0.365 0.313,0.198 10 false ★ 5.25,2.313 5.563,2.51 0.313,0.198 10 false ★ 4.104,0.563 4.417,0.76 0.313,0.198 10 false x2 4.792,2.458 5.104,2.656 0.313,0.198 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR BUMPER ASSEMBLY - - - -
2 POWER BACK DOOR UNIT ASSEMBLY SET 68920 (Click here) - -
3 POWER BACK DOOR SENSOR ASSEMBLY 84280D (Click here) - -
4 BACK DOOR DAMPER STAY UPPER BRACKET 68946 - - -
5 BACK DOOR DAMPER STAY LOWER BRACKET 68948 - - -

★ Precoated part - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 68920 2.REMOVE POWER BACK DOOR UNIT ASSEMBLY SET

Z101186

CAUTION:
·
B611130

Do not perform work if the back door is not securely supported.

·

The back door could fall, resulting in injury.



NOTICE:
·

Avoid touching the piston rod as possible to prevent foreign matter from attaching to it. Be sure to hold the cylinder while servicing.

·

Do not wear cotton gloves or other similar materials when handling the piston rod. Fibers may attach to the rod and result in gas leaks.

·

Do not apply any horizontal load to the power back door unit assembly set in order to prevent the piston rod from deforming.




a.
B625757N01
2.917,3.313 3.531,3.646 0.615,0.333 18 true i, ii 1.125,0.26 1.74,0.594 0.615,0.333 18 true iii, iv 4.781,2.573 5.396,2.906 0.615,0.333 18 true iii, iv

i.

Disconnect the connector.


ii.

Disengage the clamp.


iii.

Using a screwdriver with its tip wrapped in protective tape, slightly raise the 2 stop rings as shown in the illustration.

NOTICE:

Do not remove the stop ring. When removed the stop ring, make sure to replace with a new one.



iv.

Disengage the 2 ball joints to remove the power back door unit assembly set.

NOTICE:

Remove the power back door unit assembly set while supporting the back door by hand.




Hide 84280D 3.REMOVE POWER BACK DOOR SENSOR ASSEMBLY

Hide 68946 4.REMOVE BACK DOOR DAMPER STAY UPPER BRACKET

a.
B609489


Hide 68948 5.REMOVE BACK DOOR DAMPER STAY LOWER BRACKET

a.
B609490