Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM38G0E _59 Vehicle Exterior _100887 DOOR / HATCH _0468264 POWER BACK DOOR SYSTEM C

DOOR / HATCH  POWER BACK DOOR SYSTEM  B222631  PBD Unit Pulse Sensor LH Circuit No Signal  


DESCRIPTION

This DTC is output when the multiplex network door ECU detects a power back door unit assembly set LH pulse malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B222631 PBD Unit Pulse Sensor LH Circuit No Signal Multiplex network door ECU detects power back door unit assembly set LH pulse malfunction
·

Multiplex network door ECU

·

Power back door unit assembly set LH

·

Harness or connector


Back Door A

WIRING DIAGRAM

E357347E72
4.073,2.625 4.531,2.823 0.458,0.198 10 false T2 4.094,2.802 5.969,3.094 1.875,0.292 10 false Multiplex Network Door ECU 4.333,2.073 4.792,2.271 0.458,0.198 10 false DSG 4.323,1.563 4.781,1.76 0.458,0.198 10 false DSV 4.344,1.042 4.802,1.24 0.458,0.198 10 false DS2 4.333,0.521 4.792,0.719 0.458,0.198 10 false DS1 2.115,0.604 2.573,0.802 0.458,0.198 10 false DS1 2.125,1.125 2.583,1.323 0.458,0.198 10 false DS2 2.094,1.646 2.552,1.844 0.458,0.198 10 false DSV 2.083,2.167 2.542,2.365 0.458,0.198 10 false DSG 4.938,0.885 5.396,1.083 0.458,0.198 10 false CPU 5.104,1.448 5.563,1.646 0.458,0.198 10 false +B 4.073,0.51 4.271,0.708 0.198,0.198 10 false 13 4.135,1.01 4.292,1.208 0.156,0.198 10 false 5 2.458,1.542 2.615,1.74 0.156,0.198 10 false 2 2.469,2.073 2.625,2.271 0.156,0.198 10 false 5 2.458,0.521 2.615,0.719 0.156,0.198 10 false 1 2.469,1.021 2.625,1.219 0.156,0.198 10 false 4 4.125,1.552 4.438,1.75 0.313,0.198 10 false 4 4.063,2.073 4.375,2.271 0.313,0.198 10 false 11 1.292,2.646 1.75,2.844 0.458,0.198 10 false c1 1.313,2.813 2.698,3.156 1.385,0.344 10 false Power Back Door Unit Assembly Set LH

CAUTION / NOTICE / HINT

NOTICE:

If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Back Door > Clear DTCs
50002 489

Result:
Proceed to
NEXT



NEXT

2.REPRODUCE DTC
2.REPRODUCE DTC
a.

Turn the ignition switch to ON and wait for at least 10 seconds.

Body Electrical > Back Door > Trouble Codes
50001 489

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Back Door > Trouble Codes
50001 489

Result:
Result Proceed to
B222631 is output A
B222631 is not output B



A

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY SET LH)

B

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY SET LH)

Pre-procedure1

a.

Disconnect the T2 multiplex network door ECU connector.


b.

Disconnect the c1 power back door unit assembly set LH connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T2,c1)Location & Routing

Click Connector(T2)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Multiplex Network Door ECU

Click Connector(c1)Body>No. 8 Floor Wire>Power Back Door Unit Assembly Set LH

T2-11 (DSG) - c1-5 (DSG) Always Below 1 Ω
T2-4 (DSV) - c1-2 (DSV) Always Below 1 Ω
T2-5 (DS2) - c1-4 (DS2) Always Below 1 Ω
T2-13 (DS1) - c1-1 (DS1) Always Below 1 Ω
T2-11 (DSG) or c1-5 (DSG) - Body ground Always 10 kΩ or higher
T2-4 (DSV) or c1-2 (DSV) - Body ground Always 10 kΩ or higher
T2-5 (DS2) or c1-4 (DS2) - Body ground Always 10 kΩ or higher
T2-13 (DS1) or c1-1 (DS1) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

5.CHECK MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK MULTIPLEX NETWORK DOOR ECU

Pre-procedure1

a.

Disconnect the c1 power back door unit assembly set LH connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(c1)Location & Routing

Click Connector(c1)Body>No. 8 Floor Wire>Power Back Door Unit Assembly Set LH

c1-5 (DSG) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(c1)Location & Routing

Click Connector(c1)Body>No. 8 Floor Wire>Power Back Door Unit Assembly Set LH

c1-1 (DS1) - Body ground Always 7 V or higher
c1-4 (DS2) - Body ground Always 7 V or higher
c1-2 (DSV) - Body ground Always 7 V or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

6.CHECK POWER BACK DOOR UNIT ASSEMBLY SET LH

NG

REPLACE MULTIPLEX NETWORK DOOR ECU

6.CHECK POWER BACK DOOR UNIT ASSEMBLY SET LH
a.

Using an oscilloscope, check the waveform of each terminal from the rear of the multiplex network door ECU connector.

E440519C03
0.75,0.719 1.25,0.969 0.5,0.25 0.906,1.708 1.208,2.302 true 0.729,1.823 0.49,2.281 true 4.271,2.052 4.729,2.25 0.458,0.198 10 false GND 6.813,2.052 7.156,2.302 0.344,0.25 10 false GND 0.083,0.073 0.542,0.271 0.458,0.198 10 false *a 0.906,0.771 1.365,0.969 0.458,0.198 10 false T2 1.188,2.302 1.646,2.5 0.458,0.198 10 false DS2 0.24,2.292 0.698,2.49 0.458,0.198 10 false DS1 2.115,0.563 2.573,0.76 0.458,0.198 10 false *b 4.688,0.542 5.146,0.74 0.458,0.198 10 false *c
*a Component with harness connected
(Multiplex Network Door ECU)
*b Waveform (CH1)
*c Waveform (CH2) - -


Measurement Condition:
Item Condition
Tester Connection
·

CH1: T2-13 (DS1) - Body ground

·

CH2: T2-5 (DS2) - Body ground


Tool Setting 2 V/DIV., 2 ms./DIV.
Vehicle Condition Open and close the back door by hand.


HINT:

The period changes in accordance to the speed at which the back door is opened and closed by hand.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPLACE POWER BACK DOOR UNIT ASSEMBLY SET LH