Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM38G0E _59 Vehicle Exterior _100887 DOOR / HATCH _0468264 POWER BACK DOOR SYSTEM C

DOOR / HATCH  POWER BACK DOOR SYSTEM  B225101  Back Door Closer Switch General Electrical Failure  


DESCRIPTION

The multiplex network door ECU receives signals from the latch switch, initial switch, pawl switch and back door courtesy switch, which are built into the back door lock assembly. Based on these switch signals, the latch position of the back door lock with courtesy light switch assembly is determined.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B225101 Back Door Closer Switch General Electrical Failure While the back door closer is operating, a malfunction is detected in position information from the back door courtesy switch within a specified amount of time.
·

Back door lock with courtesy light switch assembly

·

Harness or connector

·

Multiplex network door ECU


Back Door A

WIRING DIAGRAM

B618822E04
5.833,2.917 6.146,3.115 0.313,0.198 10 false T1 5.854,3.083 7,3.417 1.146,0.333 10 false Multiplex Network Door ECU 0.073,3.125 3.448,3.365 3.375,0.24 10 false Back Door Lock with Courtesy Light Switch Assembly 2.594,0.417 3.052,0.615 0.458,0.198 10 false CLS 3.01,0.406 3.167,0.604 0.156,0.198 10 false 3 2.573,0.906 3.031,1.104 0.458,0.198 10 false OPN 3,0.906 3.156,1.104 0.156,0.198 10 false 6 2.5,1.406 3.115,1.604 0.615,0.198 10 false POLE 3,1.406 3.156,1.604 0.156,0.198 10 false 2 2.594,1.927 3.052,2.125 0.458,0.198 10 false CYT 3.01,1.927 3.167,2.125 0.156,0.198 10 false 4 5.844,0.406 6,0.604 0.156,0.198 10 false 5 6.094,0.5 6.552,0.698 0.458,0.198 10 false HAF 5.792,0.906 6.104,1.104 0.313,0.198 10 false 15 6.094,1.021 6.552,1.219 0.458,0.198 10 false POS 5.792,1.417 6.104,1.615 0.313,0.198 10 false 13 6.094,1.51 6.708,1.708 0.615,0.198 10 false PAWL 5.854,1.906 6.01,2.104 0.156,0.198 10 false 3 6.083,2.021 6.542,2.219 0.458,0.198 10 false FUL 2.76,2.427 2.917,2.625 0.156,0.198 10 false E 3,2.427 3.156,2.625 0.156,0.198 10 false 1 0.073,2.917 0.385,3.115 0.313,0.198 10 false g6 1.313,0.698 2.177,0.927 0.865,0.229 10 false Latch Switch 1.313,1.698 2.115,1.938 0.802,0.24 10 false Pawl Switch 0.927,2.219 2.656,2.427 1.729,0.208 10 false Back Door Courtesy Switch 1.292,1.188 2.135,1.406 0.844,0.219 10 false Initial Switch

CAUTION / NOTICE / HINT

NOTICE:
·

If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Half Latch Switch Latch switch signal ON or OFF OFF: Back door lock motor full-latched or half-latched -
Body Electrical > Back Door > Data List
Tester Display
Half Latch Switch
50003 489 1003

Result:
Result Proceed to
The value of Half Latch Switch is OFF A
None of the above conditions are met B



A

2.READ VALUE USING GTS

B

4.INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY
2.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Half Latch Switch Latch switch signal ON or OFF ON: Back door lock motor open-latched -
Body Electrical > Back Door > Data List
Tester Display
Half Latch Switch
50003 489 1003

Result:
Result Proceed to
The value of Half Latch Switch is ON A
None of the above conditions are met B



A

3.READ VALUE USING GTS

B

4.INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY
3.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Courtesy Switch Back door courtesy switch signal ON or OFF ON: Back door open
OFF: Back door closed
-
Body Electrical > Back Door > Data List
Tester Display
Courtesy Switch
50003 489 1018

Result:
Result Proceed to
The value of Courtesy Switch is OFF A
None of the above conditions are met B



A

REPLACE MULTIPLEX NETWORK DOOR ECU

B

4.INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY
4.INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

Pre-procedure1

a.

Disconnect the T1 multiplex network door ECU connector.


b.

Disconnect the g6 back door lock with courtesy light switch assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(g6,T1)Location & Routing

Click Connector(g6)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

Click Connector(T1)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Multiplex Network Door ECU

g6-3 (CLS) - T1-5 (HAF) Always Below 1 Ω
g6-4 (CTY) - T1-3 (FUL) Always Below 1 Ω
g6-1 (E) - Body ground Always Below 1 Ω
g6-3 (CLS) or T1-5 (HAF) - Body ground Always 10 kΩ or higher
g6-4 (CTY) or T1-3 (FUL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR