The back door lock with courtesy light switch assembly is controlled by the multiplex network door ECU. The multiplex network door ECU is activated according to the switch signals in the back door lock with courtesy light switch assembly.
Inspect fuses for circuits related to this system before performing the following inspection procedure.
If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Check if the back door can be fully closed by hand.
| Result | Proceed to |
|---|---|
| The back door can be closed normally | A |
| The back door cannot be closed normally | B |
A
B
Disconnect the T1, T3 and T4 multiplex network door ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(T3)Location & Routingewd_type=routing;type=c;code=T3 Click Connector(T3)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Multiplex Network Door ECUewd_type=component;type=c;code=T3;pinno=4 |
||
| T3-4 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(T1,T4)Location & Routingewd_type=routing;type=c,c;code=T1,T4 Click Connector(T1)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Multiplex Network Door ECUewd_type=component;type=c;code=T1;pinno=7,9 Click Connector(T4)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Multiplex Network Door ECUewd_type=component;type=c;code=T4;pinno=5 |
||
| T1-7 (ECUB) - Body ground | Always | 11 to 14 V |
| T4-5 (B) - Body ground | Always | 11 to 14 V |
| T1-9 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Disconnect the T3 and T1 multiplex network door ECU connectors.
Disconnect the g5 and g6 back door lock with courtesy light switch connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(g5,T3,g6,T1)Location & Routingewd_type=routing;type=c,c,c,c;code=g5,T3,g6,T1 Click Connector(g5)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assemblyewd_type=component;type=c;code=g5;pinno=2,1 Click Connector(T3)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Multiplex Network Door ECUewd_type=component;type=c;code=T3;pinno=2,6 Click Connector(g6)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assemblyewd_type=component;type=c;code=g6;pinno=4,2,3,6,1 Click Connector(T1)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Multiplex Network Door ECUewd_type=component;type=c;code=T1;pinno=3,13,5,15 |
||
| g5-2 (M+) - T3-2 (DC+) | Always | Below 1 Ω |
| g5-1 (M-) - T3-6 (DC-) | Always | Below 1 Ω |
| g6-4 (CTY) - T1-3 (FUL) | Always | Below 1 Ω |
| g6-2 (POLE) - T1-13 (PAWL) | Always | Below 1 Ω |
| g6-3 (CLS) - T1-5 (HAF) | Always | Below 1 Ω |
| g6-6 (OPN) - T1-15 (POS) | Always | Below 1 Ω |
| g6-1 (E) - Body ground | Always | Below 1 Ω |
| g5-2 (M+) or T3-2 (DC+) - Body ground | Always | 10 kΩ or higher |
| g5-1 (M-) or T3-6 (DC-) - Body ground | Always | 10 kΩ or higher |
| g6-2 (POLE) or T1-13 (PAWL) - Body ground | Always | 10 kΩ or higher |
| g6-4 (CTY) or T1-3 (FUL) - Body ground | Always | 10 kΩ or higher |
| g6-3 (CLS) or T1-5 (HAF) - Body ground | Always | 10 kΩ or higher |
| g6-6 (OPN) or T1-15 (POS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG