Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM38G0E _59 Vehicle Exterior _100887 DOOR / HATCH _0468264 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  Power Back Door does not Operate Using Outside Switch  


DESCRIPTION

The door control switch assembly signal is sent to the multiplex network door ECU.

If the power back door does not operate using the door control switch assembly, a door control switch assembly circuit malfunction is a possible cause.

WIRING DIAGRAM

E464761E03
4.813,1.917 5.271,2.115 0.458,0.198 10 false T1 1.24,1.646 1.698,1.844 0.458,0.198 10 false g15 1.104,1.01 1.406,1.219 0.302,0.208 10 false 2 3.125,1.01 3.281,1.208 0.156,0.198 10 false 5 4.552,1.01 4.885,1.208 0.333,0.198 10 false 14 4.802,1 5.417,1.198 0.615,0.198 10 false BDDN 1.229,1.833 3.427,2.26 2.198,0.427 10 false Door Control Switch Assembly 5.76,1.135 6.375,1.333 0.615,0.198 10 false CPU 4.802,2.083 6.615,2.354 1.813,0.271 10 false Multiplex Network Door ECU 1.313,1 1.604,1.198 0.292,0.198 10 false E 2.75,1.021 3.208,1.219 0.458,0.198 10 false CLS

CAUTION / NOTICE / HINT

NOTICE:

If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Operate the multi-information display in the combination meter assembly and check the customization status.

HINT:

Select the setting tab to check this.


Display Description Default Setting Relevant ECU
System Settings Function that enables or disables the power back door operation. On On or Off Multiplex network door ECU


Result:
Result Proceed to
Customization item is "On" (power back door system operation is possible) A
Customization item is "Off" (power back door system operation is prohibited) B



A

2.CHECK POWER BACK DOOR SYSTEM CONDITION

B

SET POWER BACK DOOR FUNCTION TO ON (PERMIT POWER BACK DOOR SYSTEM OPERATION)

2.CHECK POWER BACK DOOR SYSTEM CONDITION
a.

Check the power back door system condition.


Result:
Result Proceed to
The malfunction symptom reproduces A
The malfunction symptom does not reproduce B



A

3.READ VALUE USING GTS

B

3.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
PBD Close Switch Power back door control switch assembly signal ON or OFF ON: Power back door control switch assembly pushed
OFF: Power back door control switch assembly not pushed
-
Body Electrical > Back Door > Data List
Tester Display
PBD Close Switch
50003 489 1038
OK:

The door control switch assembly functions as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

4.INSPECT DOOR CONTROL SWITCH ASSEMBLY
4.INSPECT DOOR CONTROL SWITCH ASSEMBLY

OK

5.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

NG

REPLACE DOOR CONTROL SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)
a.

Disconnect the g15 door control switch assembly connector.


b.

Disconnect the T1 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(g15,T1)Location & Routing

Click Connector(g15)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>No. 1 Power Back Door Control Switch

Click Connector(T1)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Multiplex Network Door ECU

g15-5 (CLS) - T1-14 (BDDN) Always Below 1 Ω
g15-2 (E) - Body ground Always Below 1 Ω
g15-5 (CLS) or T1-14 (BDDN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR