Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING
RM38G0E _59 Vehicle Exterior _100826 SLIDING ROOF / CONVERTIBLE _0468597 SLIDING ROOF HOUSING A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING  DISASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (DISASSEMBLY)
E463933C01
5.385,0.51 5.865,0.51 false 3.635,1.604 3.635,0.99 3.635,0.99 4.25,0.99 false 0.813,2.083 0.813,2.479 false 1.135,4.281 1.135,3.875 1.135,3.875 0.906,3.875 false 0.604,4.917 0.604,4.375 0.604,4.375 0.375,4.375 false 4.938,4.74 5.688,4.74 false 2.219,0.833 2.219,0.271 2.219,0.271 2.667,0.271 false 5.365,2.344 5.865,2.344 false 6.667,3.167 6.667,3.552 false 5.854,3.208 5.854,3.594 false 4.76,2.604 5.26,2.604 false 0.219,4.24 0.521,4.594 0.302,0.354 18 false 1 0.74,3.76 1.042,4.115 0.302,0.354 18 false 2 5.719,4.635 6.021,4.99 0.302,0.354 18 false 4 5.802,3.594 6.104,3.948 0.302,0.354 18 false 3 5.302,2.479 5.604,2.833 0.302,0.354 18 false 3 6.604,3.552 6.906,3.906 0.302,0.354 10 false *1 5.896,2.271 6.198,2.625 0.302,0.354 10 false *1 6.083,0.385 6.302,0.646 0.219,0.26 18 false 5 2.875,0.156 3.094,0.417 0.219,0.26 18 false 6 4.469,0.885 4.688,1.146 0.219,0.26 18 false 7 0.958,2.469 1.177,2.729 0.219,0.26 18 false 8 1.427,4.917 1.885,5.115 0.458,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ROOM LIGHT BRACKET - - - -
2 SLIDING ROOF DRIVE GEAR ASSEMBLY 63260H - - -
3 SLIDING ROOF SUNSHADE STOPPER 63229A - - -
4 SUNSHADE TRIM SUB-ASSEMBLY 63306 - - -
5 REAR ROOF DRIP CHANNEL - (Click here) - -
6 SLIDING ROOF DRIVE CABLE RH 63223A (Click here) - -
7 SLIDING ROOF DRIVE CABLE LH 63224A (Click here) - -
8 ROOF WIND DEFLECTOR PANEL SUB-ASSEMBLY - (Click here) - -

*1 SLIDING ROOF PIECE SUB-ASSEMBLY - -

PROCEDURE

Hide 1.REMOVE ROOM LIGHT BRACKET

a.
E463934C01
1.927,0.156 2.208,0.51 0.281,0.354 18 false i
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


i.

Remove the bolt and room light bracket as shown in the illustration.



Hide 63260H 2.REMOVE SLIDING ROOF DRIVE GEAR ASSEMBLY

a.
E463936


Hide 63229A 3.REMOVE SLIDING ROOF SUNSHADE STOPPER

HINT:

Use the same procedure for the RH and LH sides.


a.
E463935C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 63306 4.REMOVE SUNSHADE TRIM SUB-ASSEMBLY

a.
E463937C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 5.REMOVE REAR ROOF DRIP CHANNEL

Z101186

NOTICE:

Perform this procedure only when replacement of the sliding roof drive cable is necessary.



a.
E463938C01
1.885,0.042 3.26,0.396 1.375,0.354 18 false i, ii
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


HINT:

Use the same procedure for the RH and LH sides.


i.

Remove the screw.


ii.

Detach the claw and guide and remove sliding roof piece sub-assembly as shown in the illustration



b.
E463939C01
0.573,0.208 0.708,0.479 0.135,0.271 18 false i 5.938,0.219 6.073,0.49 0.135,0.271 18 true i 4.104,0.51 4.302,0.813 0.198,0.302 18 false ii
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


i.

Using a screwdriver, detach the guide as shown in the illustration.

HINT:

Tape the screwdriver tip before use.



ii.

Slide and remove the rear roof drip channel as shown in the illustration.



Hide 63223A 6.REMOVE SLIDING ROOF DRIVE CABLE RH

Z101186

NOTICE:
·

Perform this procedure only when replacement of the sliding roof drive cable is necessary.

·

When separating the sliding roof drive cable, wear protective gloves when performing work.




a.
E463940C01
1.333,0.844 1.625,1.219 0.292,0.375 18 false ii 3.281,3.031 3.573,3.406 0.292,0.375 18 false i
V113146

Push Position
V113147

Remove in this Direction
V100135

Hold Down - -


i.

Hold down the roof wind deflector panel sub-assembly.


ii.

Using a screwdriver, remove the sliding roof drive cable RH as shown in the illustration.

HINT:

Tape the screwdriver tip before use.




Hide 63224A 7.REMOVE SLIDING ROOF DRIVE CABLE LH

Z101186

NOTICE:
·

Perform this procedure only when replacement of the sliding roof drive cable is necessary.

·

When separating the sliding roof drive cable, wear protective gloves when performing work.




a.
E464949C01
3.26,1.552 3.542,1.906 0.281,0.354 18 false i 1.323,2.698 1.604,3.052 0.281,0.354 18 false ii
V113146

Push Position
V113147

Remove in this Direction
V100135

Hold Down - -


i.

Hold down the roof wind deflector panel sub-assembly.


ii.

Using a screwdriver, remove the sliding roof drive cable LH as shown in the illustration.

HINT:

Tape the screwdriver tip before use.




Hide 8.REMOVE ROOF WIND DEFLECTOR PANEL SUB-ASSEMBLY

a.
E463941C01
1.24,1.01 1.615,1.25 true 1.167,1.104 1.25,1.354 true 5.969,1.073 5.74,1.229 true 6.052,1.104 6.135,1.354 true 0.333,0.469 0.885,0.823 0.552,0.354 18 false i 5.469,0.479 6.021,0.833 0.552,0.354 18 false i 0.302,2.771 0.563,3.031 0.26,0.26 18 false ii 4.219,2.729 4.479,2.99 0.26,0.26 18 false iii 1.635,1.198 1.833,1.396 0.198,0.198 10 true *1 1.24,1.385 1.438,1.583 0.198,0.198 10 true *2 5.521,1.188 5.719,1.385 0.198,0.198 10 true *1 6.104,1.375 6.302,1.573 0.198,0.198 10 true *2
*1 Spring *2 Guide
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)
V113149

Remove in this Direction (3) - -


i.

Pull each spring in the direction indicated by the arrow (1) shown in the illustration to detach the 2 springs from the 2 guides.


ii.

Pull the roof wind deflector panel sub-assembly in the direction indicated by the arrow (2) shown in the illustration.


iii.

Detach the guide and remove the roof wind deflector panel sub-assembly in the direction indicated by the arrow (3) shown in the illustration.