Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
RM38G0E _55 Steering _100923 STEERING COLUMN _0468603 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2620A2  ECU Power Source Circuit System Voltage Low  


DESCRIPTION

The ECU power source circuit supplies positive (+) voltage to the multiplex tilt and telescopic ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2620A2 ECU Power Source Circuit System Voltage Low The voltage of the ECU power source drops to 8 V or less for 10 seconds or more.
·

ECU-DCC NO. 1 fuse

·

Harness or connector

·

Multiplex tilt and telescopic ECU


Tilt&Telescopic A

WIRING DIAGRAM

C268477E84
3.448,0.906 4.656,1.333 1.208,0.427 10 false ECU-DCC NO. 1 0.531,0.719 1.417,1.26 0.885,0.542 10 false from Battery 5.594,0.719 6.469,1.052 0.875,0.333 10 false ECUB 5.583,2.427 6.063,2.708 0.479,0.281 10 false GND2 5.354,0.625 5.531,0.896 0.177,0.271 10 false 9 5.365,2.333 5.542,2.552 0.177,0.219 10 false 8 5.427,2.948 5.906,3.188 0.479,0.24 10 false I43 5.427,3.125 6.51,3.563 1.083,0.438 10 false Multiplex Tilt and Telescopic ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)
a.

Disconnect the I43 multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I43)Location & Routing

Click Connector(I43)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multiplex Tilt & Telescopic ECU

I43-9 (ECUB) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.

Disconnect the I43 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I43)Location & Routing

Click Connector(I43)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multiplex Tilt & Telescopic ECU

I43-8 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR