Home › Steering › STEERING COLUMN › MULTIPLEX TILT AND TELESCOPIC ECU
RM38G0E _55 Steering _100923 STEERING COLUMN _0469202 MULTIPLEX TILT AND TELESCOPIC ECU A

STEERING COLUMN  MULTIPLEX TILT AND TELESCOPIC ECU  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C456725N01
2.344,3.052 2.729,3.281 2.729,3.281 2.896,3.281 true 5.75,2.771 6,3.135 6,3.135 6.167,3.135 true 4.5,1.021 4.833,1.021 true 6.521,0.219 6.854,0.219 true 6.333,0.083 6.615,0.438 0.281,0.354 18 false 1 4.917,0.896 5.292,1.198 0.375,0.302 18 false 4 3.271,3.167 3.552,3.521 0.281,0.354 18 false 2 6.26,2.99 6.573,3.281 0.313,0.292 18 false 3 3.333,2.469 3.615,2.823 0.281,0.354 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM - (Click here) - -
2 LOWER STEERING COLUMN COVER SUB-ASSEMBLY 45024 (Click here) - -
3 LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY 73900 - - -
4 MULTIPLEX TILT AND TELESCOPIC ECU - - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the multiplex tilt and telescopic ECU removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

Z101186

Click here(Click here)

Hide 45024 2.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 73900 3.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 4.REMOVE MULTIPLEX TILT AND TELESCOPIC ECU

a.
C456727