Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › ADAPTIVE HIGH BEAM SYSTEM › 2021.04–2022.11
RM38G0E _95 ADAS / AD _100650 ADVANCED DRIVER ASSISTANCE SYSTEM _0468606 ADAPTIVE HIGH BEAM SYSTEM C

ADVANCED DRIVER ASSISTANCE SYSTEM  ADAPTIVE HIGH BEAM SYSTEM  B249200  AHS Driver LH Malfunction  B249300  AHS Driver RH Malfunction  


DESCRIPTION

The headlight ECU sub-assembly sends the control signal to the light control LED ECU via LIN communication to control the LED array.

The light control LED ECU supplies boosted voltage at a certain current to the LED array and turns on/off each LED according to the adaptive high beam system control.

By monitoring the LED power supply voltage, abnormal current malfunctions can be detected.

The light control LED ECU also detects malfunctions in the switching circuit for the adaptive high beam system.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B249200 AHS Driver LH Malfunction
Detection condition:

All of the following conditions are met:

-

Ignition switch ON

-

High beam headlights on



Malfunction status:

Adaptive high beam system circuit malfunction signals are received from the light control LED ECU LH

-

LED array malfunctioning

-

Light control LED ECU LH malfunctioning

-

Open circuit or short circuit in adaptive high beam system



Malfunction duration:

-


·

Headlight unit assembly LH

·

Headlight unit LH

·

Light control LED ECU LH


Headlight Control A
B249300 AHS Driver RH Malfunction
Detection condition:

All of the following conditions are met:

-

Ignition switch ON

-

High beam headlights on



Malfunction status:

Adaptive high beam system circuit malfunction signals are received from the light control LED ECU RH

-

LED array malfunctioning

-

Light control LED ECU RH malfunctioning

-

Open circuit or short circuit in adaptive high beam system



Malfunction duration:

-


·

Headlight unit assembly RH

·

Headlight unit RH

·

Light control LED ECU RH


Headlight Control A

WIRING DIAGRAM

E442471E06
1.177,0.333 2.25,0.531 1.073,0.198 10 false LIN I/F 0.948,0.719 2.021,0.917 1.073,0.198 10 false LINL 1.521,0.719 2.594,0.917 1.073,0.198 10 false LIN1_2 0.646,0.698 0.99,0.875 0.344,0.177 10 false 20 0.635,0.885 0.865,1.063 0.229,0.177 10 false B4 2.052,0.698 2.396,0.875 0.344,0.177 10 false 13 2.094,0.875 2.281,1.052 0.188,0.177 10 false C 2.833,0.729 3.177,0.906 0.344,0.177 10 false 13 3.833,0.365 4.396,0.573 0.563,0.208 10 false LED11 3.823,0.646 4.385,0.854 0.563,0.208 10 false LED10 3.885,0.906 4.448,1.115 0.563,0.208 10 false LED9 3.896,1.188 4.458,1.396 0.563,0.208 10 false LED8 3.896,1.458 4.458,1.667 0.563,0.208 10 false LED7 3.896,1.75 4.458,1.958 0.563,0.208 10 false LED6 3.896,2.021 4.458,2.229 0.563,0.208 10 false LED5 3.896,2.313 4.458,2.521 0.563,0.208 10 false LED4 3.885,2.604 4.448,2.813 0.563,0.208 10 false LED3 3.885,2.865 4.448,3.073 0.563,0.208 10 false LED2 3.896,3.135 4.458,3.344 0.563,0.208 10 false LED1 3.896,3.417 4.458,3.625 0.563,0.208 10 false LED0 3.135,0.896 3.698,1.104 0.563,0.208 10 false LIN 4.333,0.24 4.625,0.427 0.292,0.188 10 false 15 4.354,0.521 4.646,0.708 0.292,0.188 10 false 3 4.333,0.802 4.625,0.99 0.292,0.188 10 false 16 4.344,1.063 4.635,1.25 0.292,0.188 10 false 4 4.323,1.354 4.615,1.542 0.292,0.188 10 false 17 4.344,1.635 4.635,1.823 0.292,0.188 10 false 5 4.323,1.917 4.615,2.104 0.292,0.188 10 false 18 4.344,2.198 4.635,2.385 0.292,0.188 10 false 6 4.323,2.479 4.615,2.667 0.292,0.188 10 false 19 4.344,2.75 4.635,2.938 0.292,0.188 10 false 7 4.344,3.031 4.635,3.219 0.292,0.188 10 false 20 4.344,3.302 4.635,3.49 0.292,0.188 10 false 8 5.219,0.229 5.51,0.417 0.292,0.188 10 false 12 5.281,0.521 5.573,0.708 0.292,0.188 10 false 1 5.219,0.802 5.51,0.99 0.292,0.188 10 false 13 5.281,1.083 5.573,1.271 0.292,0.188 10 false 2 5.229,1.354 5.521,1.542 0.292,0.188 10 false 14 5.281,1.635 5.573,1.823 0.292,0.188 10 false 3 5.229,1.906 5.521,2.094 0.292,0.188 10 false 15 5.271,2.188 5.563,2.375 0.292,0.188 10 false 4 5.229,2.469 5.521,2.656 0.292,0.188 10 false 16 5.281,2.76 5.573,2.948 0.292,0.188 10 false 5 5.229,3.021 5.521,3.208 0.292,0.188 10 false 17 5.292,3.302 5.583,3.49 0.292,0.188 10 false 6 5.906,1.74 6.646,2.146 0.74,0.406 10 false LED Array 0.542,4.24 3.083,4.615 2.542,0.375 10 false Headlight ECU Sub-assembly LH 2.813,3.719 4.635,3.896 1.823,0.177 10 true Light Control LED ECU LH 2.813,3.563 3.375,3.771 0.563,0.208 10 false D 4.781,3.698 6.844,3.896 2.063,0.198 10 false Headlight LED Unit Assembly LH 4.781,3.542 5.344,3.75 0.563,0.208 10 false E 3.969,4.135 6.51,4.51 2.542,0.375 10 false Headlight Unit Assembly LH 0.635,5.271 0.875,5.438 0.24,0.167 10 false B7 0.646,5.083 1.031,5.323 0.385,0.24 10 false 20 2.104,5.26 2.281,5.438 0.177,0.177 10 false C 2.063,5.083 2.448,5.323 0.385,0.24 10 false 13 2.854,5.104 3.24,5.344 0.385,0.24 10 false 13 0.948,5.094 1.333,5.333 0.385,0.24 10 false LINL 1.49,5.094 1.948,5.333 0.458,0.24 10 false LIN1_2 3.125,5.271 3.51,5.51 0.385,0.24 10 false LIN 5.906,6.406 6.604,6.75 0.698,0.344 10 false LED Array 3.813,5.01 4.375,5.219 0.563,0.208 10 false LED11 3.802,5.302 4.365,5.51 0.563,0.208 10 false LED10 3.875,5.573 4.438,5.781 0.563,0.208 10 false LED9 3.885,5.854 4.448,6.063 0.563,0.208 10 false LED8 3.885,6.135 4.448,6.344 0.563,0.208 10 false LED7 3.885,6.427 4.448,6.635 0.563,0.208 10 false LED6 3.875,6.708 4.438,6.917 0.563,0.208 10 false LED5 3.885,6.99 4.448,7.198 0.563,0.208 10 false LED4 3.885,7.271 4.448,7.479 0.563,0.208 10 false LED3 3.885,7.563 4.448,7.771 0.563,0.208 10 false LED2 3.896,7.813 4.458,8.021 0.563,0.208 10 false LED1 3.896,8.063 4.458,8.271 0.563,0.208 10 false LED0 4.323,4.906 4.615,5.094 0.292,0.188 10 false 15 4.344,5.167 4.635,5.354 0.292,0.188 10 false 3 4.323,5.458 4.615,5.646 0.292,0.188 10 false 16 4.354,5.729 4.646,5.917 0.292,0.188 10 false 4 4.323,6.01 4.615,6.198 0.292,0.188 10 false 17 4.354,6.292 4.646,6.479 0.292,0.188 10 false 5 4.323,6.573 4.615,6.76 0.292,0.188 10 false 18 4.344,6.854 4.635,7.042 0.292,0.188 10 false 6 4.323,7.135 4.615,7.323 0.292,0.188 10 false 19 4.354,7.406 4.646,7.594 0.292,0.188 10 false 7 4.333,7.677 4.625,7.865 0.292,0.188 10 false 20 4.344,7.969 4.635,8.156 0.292,0.188 10 false 8 5.208,4.906 5.5,5.094 0.292,0.188 10 false 12 5.271,5.177 5.563,5.365 0.292,0.188 10 false 1 5.219,5.448 5.51,5.635 0.292,0.188 10 false 13 5.271,5.719 5.563,5.906 0.292,0.188 10 false 2 5.24,6 5.531,6.188 0.292,0.188 10 false 14 5.271,6.292 5.563,6.479 0.292,0.188 10 false 3 5.229,6.573 5.521,6.76 0.292,0.188 10 false 15 5.281,6.854 5.573,7.042 0.292,0.188 10 false 4 5.229,7.135 5.521,7.323 0.292,0.188 10 false 16 5.271,7.406 5.563,7.594 0.292,0.188 10 false 5 5.229,7.677 5.521,7.865 0.292,0.188 10 false 17 5.281,7.969 5.573,8.156 0.292,0.188 10 false 6 0.542,8.885 3.083,9.26 2.542,0.375 10 false Headlight ECU Sub-assembly RH 2.813,8.198 3.375,8.406 0.563,0.208 10 false D 2.833,8.365 4.823,8.573 1.99,0.208 10 true Light Control LED ECU RH 4.781,8.198 5.344,8.406 0.563,0.208 10 false E 4.781,8.365 6.896,8.573 2.115,0.208 10 false Headlight LED Unit Assembly RH 4.031,8.802 6.573,9.177 2.542,0.375 10 false Headlight Unit Assembly RH 0.865,9.365 2.51,9.552 1.646,0.188 10 false : LIN Communication Line

PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC

Pre-procedure1

a.

Turn the ignition switch to ON.


b.

Operate the light control switch to turn on the high beam headlights.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B249200 and B249300 are not output A
B249200 is output B
B249300 is output C



Post-procedure1

d.

None



A

B

3.INSPECT HEADLIGHT UNIT ASSEMBLY LH

C

5.INSPECT HEADLIGHT UNIT ASSEMBLY RH
3.INSPECT HEADLIGHT UNIT ASSEMBLY LH

Pre-procedure1

a.

Remove the headlight unit assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

E442704C05
1.854,0.573 2.198,0.833 0.344,0.26 4.99,0.563 5.333,0.823 0.344,0.26 1.552,1.594 1.021,1.25 false 2.01,1.854 2.333,2.271 false 1.49,2.208 1.708,1.844 false 1.698,1.594 1.385,1.104 false 1.844,1.583 1.802,1.094 false 2.031,1.594 2.167,1.083 false 2.177,1.594 2.625,1.083 false 2.323,1.594 3.052,1.104 false 1.01,2.177 1.563,1.844 false 1.917,2.25 1.896,1.844 false 2.156,1.854 2.74,2.219 false 2.292,1.844 3.198,2.135 false 1.073,0.677 1.385,0.875 0.313,0.198 10 false *a 4.292,0.583 4.604,0.781 0.313,0.198 10 false *b 1.99,0.635 2.302,0.833 0.313,0.198 10 false D 5.125,0.615 5.438,0.813 0.313,0.198 10 false E 1.792,2.281 2.281,2.51 0.49,0.229 10 false LED7 1.354,2.25 1.792,2.521 0.438,0.271 10 false LED9 0.833,2.219 1.292,2.396 0.458,0.177 10 false LED11 0.792,1.094 1.229,1.375 0.438,0.281 10 false LED10 1.229,0.958 1.667,1.24 0.438,0.281 10 false LED8 1.656,0.948 2.094,1.229 0.438,0.281 10 false LED6 2.042,0.938 2.479,1.219 0.438,0.281 10 false LED4 2.51,0.938 2.948,1.219 0.438,0.281 10 false LED2 3.104,1.021 3.542,1.302 0.438,0.281 10 false LED0 2.25,2.302 2.74,2.531 0.49,0.229 10 false LED5 2.698,2.25 3.188,2.479 0.49,0.229 10 false LED3 3.25,2.094 3.74,2.323 0.49,0.229 10 false LED1
*a Component without harness connected
(to Light Control LED ECU LH)
*b Component without harness connected
(to Headlight Unit LH)


Standard Resistance:
Tester Connection Condition Specified Condition
D-15 (LED11) - E-12 Always Below 1 Ω
D-3 (LED10) - E-1 Always Below 1 Ω
D-16 (LED9) - E-13 Always Below 1 Ω
D-4 (LED8) - E-2 Always Below 1 Ω
D-17 (LED7) - E-14 Always Below 1 Ω
D-5 (LED6) - E-3 Always Below 1 Ω
D-18 (LED5) - E-15 Always Below 1 Ω
D-6 (LED4) - E-4 Always Below 1 Ω
D-19 (LED3) - E-16 Always Below 1 Ω
D-7 (LED2) - E-5 Always Below 1 Ω
D-20 (LED1) - E-17 Always Below 1 Ω
D-8 (LED0) - E-6 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

4.INSPECT HEADLIGHT UNIT LH

NG

REPLACE HEADLIGHT UNIT ASSEMBLY LH

4.INSPECT HEADLIGHT UNIT LH

Pre-procedure1

a.

Set the Toyota Electrical Tester to diode check mode.

HINT:

If the tester display is below 3 V, replace the dry cell batteries inside the tester.



Procedure1

b.

Add 1 dry cell battery (about 1.5 V) between the Toyota Electrical Tester and inspection terminal and check if the LED illuminates.

E442470C01
5.094,0.573 5.417,0.813 0.323,0.24 1.802,1.406 2.083,1.917 2.083,1.917 2.25,1.917 false 4.115,1.396 4.781,1.646 false 4.25,1.167 4.927,1.635 false 4.646,1.125 5.073,1.625 false 5.125,1.135 5.208,1.635 false 5.479,1.146 5.417,1.635 false 5.875,1.146 5.552,1.635 false 4.302,2.146 4.781,1.885 false 4.635,2.188 4.927,1.885 false 5.031,2.208 5.083,1.885 false 5.396,2.25 5.24,1.885 false 5.781,2.24 5.427,1.885 false 6.156,2.177 5.552,1.896 false 4.365,0.594 4.677,0.792 0.313,0.198 10 false *a 5.219,0.625 5.531,0.823 0.313,0.198 10 false D 2.313,1.854 2.625,2.052 0.313,0.198 10 false *1 3.688,1.313 4.354,1.594 0.667,0.281 10 false LED10 4.031,1 4.698,1.281 0.667,0.281 10 false LED8 4.49,0.958 5.156,1.24 0.667,0.281 10 false LED6 4.948,0.969 5.615,1.25 0.667,0.281 10 false LED4 5.365,0.979 6.031,1.26 0.667,0.281 10 false LED2 5.802,0.99 6.469,1.271 0.667,0.281 10 false LED0 3.896,2.125 4.563,2.406 0.667,0.281 10 false LED11 4.448,2.208 5.115,2.49 0.667,0.281 10 false LED9 4.865,2.25 5.531,2.531 0.667,0.281 10 false LED7 5.292,2.281 5.958,2.563 0.667,0.281 10 false LED5 5.698,2.281 6.365,2.563 0.667,0.281 10 false LED3 6.208,2.135 6.875,2.417 0.667,0.281 10 false LED1
*1 Dry Cell Battery - -
*a Component without harness connected
(to Light Control LED ECU LH)
- -


OK:
Tester Connection Specified Condition
Tester positive (+) - D-15 (LED11)
Tester negative (-) - D-3 (LED10)
LED illuminates
Tester positive (+) - D-3 (LED10)
Tester negative (-) - D-16 (LED9)
LED illuminates
Tester positive (+) - D-16 (LED9)
Tester negative (-) - D-4 (LED8)
LED illuminates
Tester positive (+) - D-4 (LED8)
Tester negative (-) - D-17 (LED7)
LED illuminates
Tester positive (+) - D-17 (LED7)
Tester negative (-) - D-5 (LED6)
LED illuminates
Tester positive (+) - D-5 (LED6)
Tester negative (-) - D-18 (LED5)
LED illuminates
Tester positive (+) - D-18 (LED5)
Tester negative (-) - D-6 (LED4)
LED illuminates
Tester positive (+) - D-6 (LED4)
Tester negative (-) - D-19 (LED3)
LED illuminates
Tester positive (+) - D-19 (LED3)
Tester negative (-) - D-7 (LED2)
LED illuminates
Tester positive (+) - D-7 (LED2)
Tester negative (-) - D-20 (LED1)
LED illuminates
Tester positive (+) - D-20 (LED1)
Tester negative (-) - D-8 (LED0)
LED illuminates


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE LIGHT CONTROL LED ECU LH

NG

5.INSPECT HEADLIGHT UNIT ASSEMBLY RH

Pre-procedure1

a.

Remove the headlight unit assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

E442704C05
1.854,0.573 2.198,0.833 0.344,0.26 4.99,0.563 5.333,0.823 0.344,0.26 1.552,1.594 1.021,1.25 false 2.01,1.854 2.333,2.271 false 1.49,2.208 1.708,1.844 false 1.698,1.594 1.385,1.104 false 1.844,1.583 1.802,1.094 false 2.031,1.594 2.167,1.083 false 2.177,1.594 2.625,1.083 false 2.323,1.594 3.052,1.104 false 1.01,2.177 1.563,1.844 false 1.917,2.25 1.896,1.844 false 2.156,1.854 2.74,2.219 false 2.292,1.844 3.198,2.135 false 1.073,0.677 1.385,0.875 0.313,0.198 10 false *a 4.292,0.583 4.604,0.781 0.313,0.198 10 false *b 1.99,0.635 2.302,0.833 0.313,0.198 10 false D 5.125,0.615 5.438,0.813 0.313,0.198 10 false E 1.792,2.281 2.281,2.51 0.49,0.229 10 false LED7 1.354,2.25 1.792,2.521 0.438,0.271 10 false LED9 0.833,2.219 1.292,2.396 0.458,0.177 10 false LED11 0.792,1.094 1.229,1.375 0.438,0.281 10 false LED10 1.229,0.958 1.667,1.24 0.438,0.281 10 false LED8 1.656,0.948 2.094,1.229 0.438,0.281 10 false LED6 2.042,0.938 2.479,1.219 0.438,0.281 10 false LED4 2.51,0.938 2.948,1.219 0.438,0.281 10 false LED2 3.104,1.021 3.542,1.302 0.438,0.281 10 false LED0 2.25,2.302 2.74,2.531 0.49,0.229 10 false LED5 2.698,2.25 3.188,2.479 0.49,0.229 10 false LED3 3.25,2.094 3.74,2.323 0.49,0.229 10 false LED1
*a Component without harness connected
(to Light Control LED ECU RH)
*b Component without harness connected
(to Headlight Unit RH)


Standard Resistance:
Tester Connection Condition Specified Condition
D-15 (LED11) - E-12 Always Below 1 Ω
D-3 (LED10) - E-1 Always Below 1 Ω
D-16 (LED9) - E-13 Always Below 1 Ω
D-4 (LED8) - E-2 Always Below 1 Ω
D-17 (LED7) - E-14 Always Below 1 Ω
D-5 (LED6) - E-3 Always Below 1 Ω
D-18 (LED5) - E-15 Always Below 1 Ω
D-6 (LED4) - E-4 Always Below 1 Ω
D-19 (LED3) - E-16 Always Below 1 Ω
D-7 (LED2) - E-5 Always Below 1 Ω
D-20 (LED1) - E-17 Always Below 1 Ω
D-8 (LED0) - E-6 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

6.INSPECT HEADLIGHT UNIT RH

NG

REPLACE HEADLIGHT UNIT ASSEMBLY RH

6.INSPECT HEADLIGHT UNIT RH

Pre-procedure1

a.

Set the Toyota Electrical Tester to diode check mode.

HINT:

If the tester display is below 3 V, replace the dry cell batteries inside the tester.



Procedure1

b.

Add 1 dry cell battery (about 1.5 V) between the Toyota Electrical Tester and inspection terminal and check if the LED illuminates.

E442470C01
5.094,0.573 5.417,0.813 0.323,0.24 1.802,1.406 2.083,1.917 2.083,1.917 2.25,1.917 false 4.115,1.396 4.781,1.646 false 4.25,1.167 4.927,1.635 false 4.646,1.125 5.073,1.625 false 5.125,1.135 5.208,1.635 false 5.479,1.146 5.417,1.635 false 5.875,1.146 5.552,1.635 false 4.302,2.146 4.781,1.885 false 4.635,2.188 4.927,1.885 false 5.031,2.208 5.083,1.885 false 5.396,2.25 5.24,1.885 false 5.781,2.24 5.427,1.885 false 6.156,2.177 5.552,1.896 false 4.365,0.594 4.677,0.792 0.313,0.198 10 false *a 5.219,0.625 5.531,0.823 0.313,0.198 10 false D 2.313,1.854 2.625,2.052 0.313,0.198 10 false *1 3.688,1.313 4.354,1.594 0.667,0.281 10 false LED10 4.031,1 4.698,1.281 0.667,0.281 10 false LED8 4.49,0.958 5.156,1.24 0.667,0.281 10 false LED6 4.948,0.969 5.615,1.25 0.667,0.281 10 false LED4 5.365,0.979 6.031,1.26 0.667,0.281 10 false LED2 5.802,0.99 6.469,1.271 0.667,0.281 10 false LED0 3.896,2.125 4.563,2.406 0.667,0.281 10 false LED11 4.448,2.208 5.115,2.49 0.667,0.281 10 false LED9 4.865,2.25 5.531,2.531 0.667,0.281 10 false LED7 5.292,2.281 5.958,2.563 0.667,0.281 10 false LED5 5.698,2.281 6.365,2.563 0.667,0.281 10 false LED3 6.208,2.135 6.875,2.417 0.667,0.281 10 false LED1
*1 Dry Cell Battery - -
*a Component without harness connected
(to Light Control LED ECU RH)
- -


OK:
Tester Connection Specified Condition
Tester positive (+) - D-15 (LED11)
Tester negative (-) - D-3 (LED10)
LED illuminates
Tester positive (+) - D-3 (LED10)
Tester negative (-) - D-16 (LED9)
LED illuminates
Tester positive (+) - D-16 (LED9)
Tester negative (-) - D-4 (LED8)
LED illuminates
Tester positive (+) - D-4 (LED8)
Tester negative (-) - D-17 (LED7)
LED illuminates
Tester positive (+) - D-17 (LED7)
Tester negative (-) - D-5 (LED6)
LED illuminates
Tester positive (+) - D-5 (LED6)
Tester negative (-) - D-18 (LED5)
LED illuminates
Tester positive (+) - D-18 (LED5)
Tester negative (-) - D-6 (LED4)
LED illuminates
Tester positive (+) - D-6 (LED4)
Tester negative (-) - D-19 (LED3)
LED illuminates
Tester positive (+) - D-19 (LED3)
Tester negative (-) - D-7 (LED2)
LED illuminates
Tester positive (+) - D-7 (LED2)
Tester negative (-) - D-20 (LED1)
LED illuminates
Tester positive (+) - D-20 (LED1)
Tester negative (-) - D-8 (LED0)
LED illuminates


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE LIGHT CONTROL LED ECU RH

NG