| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | HEADLIGHT ECU SUB-ASSEMBLY LH | 81056A | - | - | - |
| 2 | HEADLIGHT GASKET | 81134 | - | - | - |
| 3 | NO. 1 HEADLIGHT PROTECTOR LH | 81176 | - | - | - |
| *A | w/ Headlight ECU | - | - |
| *1 | Headlight ECU LH | - | - |
| ● | Non-reusable part | - | - |
| *A | w/o Headlight ECU | *B | w/ Sequential Turn Light |
| *1 | Headlight Housing LH | *2 | Gasket |
| ● | Non-reusable part | - | - |
| *A | w/ Headlight ECU | - | - |
| *1 | Headlight Housing LH | *2 | Gasket |
| *3 | BASE B ASSEMBLY | - | - |
| ● | Non-reusable part | - | - |
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
81056A 1.REMOVE HEADLIGHT ECU SUB-ASSEMBLY LH (w/ Headlight ECU)
81134 2.REMOVE HEADLIGHT GASKET (w/ Headlight ECU)
81176 3.REMOVE NO. 1 HEADLIGHT PROTECTOR LH
81165 4.REMOVE HEADLIGHT CORD LH (w/o Headlight ECU)
81144 5.REMOVE NO. 1 HEADLIGHT COVER
| *A | w/ Headlight ECU | *B | w/o Headlight ECU |
|
Remove in this Direction |
|
Connector |
8110B 6.REMOVE HEADLIGHT LENS SUB-ASSEMBLY LH
|
|
| *A | w/ Sequential Turn Light | *B | w/o Headlight ECU |
| *A | w/ Headlight ECU | - | - |
| *a | TORX Screw | - | - |
|
Place Hand Here |
|
Screw |
w/ Headlight ECU:
Remove the 7 screws.
Using a T20H "TORX" driver, remove the "TORX" screw.
w/o Headlight ECU:
Remove the 6 screws.
Using a T20H "TORX" driver, remove the "TORX" screw.
Place your hands at the positions shown in the illustration and detach the claw.
| *a | 7.6 mm (0.299 in.) | - | - |
Prepare the cable tie of approximately 7.6 mm (0.299 in.) in width.
It will be difficult to pull out the headlight lens gasket with a cable tie with a narrow width (2.5 mm (0.0984 in.), etc.).
Use a heat light to heat the headlight lens gasket near the location where the cable tie is inserted from the backside of the headlight housing LH.
To prevent the headlight housing LH from deformation or damage, do not heat one part intensively and do not heat with a temperature of 120 °C (248 °F) or higher.
When the headlight lens gasket is heated, it softens and becomes easier to pull out.
| *1 | Cable Tie | *2 | Headlight Lens Gasket |
| *3 | Headlight Lens LH | *4 | Headlight Housing LH |
Insert the cable tie until it sticks into the headlight lens gasket as shown in the illustration.
Do not damage the groove of the headlight housing LH gasket or the headlight lens.
Pull out the cable tie and headlight lens gasket together.
Pull out the headlight lens gasket until there is no contact between the headlight lens sub-assembly LH and the headlight housing LH.
If the headlight lens gasket disconnects while it is pulled out, insert the cable tie again and pull out the headlight lens gasket.
|
Remove in this Direction | - | - |
Remove the headlight lens gasket from the headlight housing LH.
81132B 7.REMOVE HEADLIGHT LENS GASKET
|
|
81171A 8.REMOVE HEADLIGHT UNIT LH
|
|
| *A | w/ Headlight ECU | *B | w/o Headlight ECU |
Using a vernier caliper, record the dimensions of a and b shown in the illustration.
| *A | w/ Headlight ECU | *B | w/o Headlight ECU |
Disconnect the each connector and detach the wire harness clamp.
| *A | w/ Headlight ECU | *B | w/o Headlight ECU |
| *1 | Pivot Collar | - | - |
|
Place Hand Here |
|
Turn in this Direction |
|
Remove in this Direction | - | - |
Loosen the aiming screws for beam axis vertical and horizontal adjustments counterclockwise by 10 turns.
Place your hand in a protective glove at the position in the illustration, pull in the direction shown in the illustration, and disconnect the pivot collar.
| *A | w/ Headlight ECU | *B | w/o Headlight ECU |
|
Turn in this Direction | - | - |
Hold the headlight unit assembly LH with one hand to prevent it from tipping over and loosen the aiming screws for beam axis vertical and horizontal adjustments counterclockwise until the headlight unit assembly LH is disconnected.
81156A 10.REMOVE HEADLIGHT BRACKET LH (w/ Headlight ECU)
85691 11.REMOVE HEADLIGHT LEVELING MOTOR LH
w/ Headlight ECU:
|
Remove in this Direction | - | - |
w/o Headlight ECU:
|
Turn in this Direction | - | - |
81160A 12.REMOVE HEADLIGHT LED UNIT ASSEMBLY LH (w/ Headlight ECU)
Using a T20 "TORX" socket wrench, remove the 3 "TORX" screws and headlight LED unit assembly LH.
Detach the guide and remove the headlight LED unit assembly.
81117B 13.REMOVE GASKET (w/ Headlight ECU)