Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0468612 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B583238E03
0.823,0.156 2.563,0.375 1.74,0.219 10 false from Battery 1.667,1.865 3.646,2.063 1.979,0.198 10 false Horn Relay Assembly (HORN) 1.104,1.094 1.719,1.292 0.615,0.198 10 false HORN 6.115,0.844 6.729,1.042 0.615,0.198 10 false HORN 2.573,4.76 3.708,5.125 1.135,0.365 10 false Low Pitched Horn Assembly 4.198,4.75 5.344,5.125 1.146,0.375 10 false High Pitched Horn Assembly 4.844,1.938 6.031,2.677 1.188,0.74 10 false Power Distribution Box Assembly 6.125,3.375 7.063,4.198 0.938,0.823 10 false Main Body ECU (Multiplex Network Body ECU) 2.021,0.844 2.24,1.042 0.219,0.198 10 false 1 2.948,1.458 3.167,1.656 0.219,0.198 10 false 5 2.938,0.833 3.156,1.031 0.219,0.198 10 false 2 2.052,1.438 2.271,1.635 0.219,0.198 10 false 3 2.26,4.5 2.479,4.698 0.219,0.198 10 false 1 3.875,4.521 4.094,4.719 0.219,0.198 10 false 1 2.594,4.583 2.948,4.781 0.354,0.198 10 false B33 4.198,4.573 4.552,4.771 0.354,0.198 10 false B32 4.781,4.031 5.958,4.615 1.177,0.583 10 false to Steering Pad Switch Assembly 5.865,0.823 6.219,1.021 0.354,0.198 10 false 23 6.135,3.208 6.49,3.406 0.354,0.198 10 false A 6.74,1.021 7.094,1.219 0.354,0.198 10 false IC 4.656,0.76 5.385,0.948 0.729,0.188 10 false 11 4.646,0.938 5,1.135 0.354,0.198 10 false 5E 4.646,1.354 5,1.552 0.354,0.198 10 false 5B 4.656,1.177 5.385,1.365 0.729,0.188 10 false 43

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.CHECK HORNS OPERATION
a.

Press the horn switch and check if the horns sound.


Result:
Proceed to
Horns sound
Horns do not sound



Horns sound

2.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

Horns do not sound

2.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

b.
E439027C06
1.458,0.188 1.917,0.5 0.458,0.313 1.448,1.594 1.906,1.906 0.458,0.313 2.448,1.198 2.615,0.885 true 2.219,1.198 2.448,1.198 false 1.646,0.292 1.865,0.5 0.219,0.208 10 false A 1.573,1.656 1.823,1.844 0.25,0.188 10 false 5E 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.771,1.115 2.385,1.313 0.615,0.198 10 false HORN
*a Component without harness connected
(Power Distribution Box Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5E-11 - A-23 (HORN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG