Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0468612 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Theft Warning Siren Circuit  


DESCRIPTION

The theft warning siren assembly has an internal battery. If the vehicle battery cable is disconnected or any of the communication lines are open, the theft warning siren assembly detects this and sounds its siren.

Although the theft warning siren assembly usually sounds by receiving a signal from the main body ECU (multiplex network body ECU), the theft warning siren assembly can sound by its internal battery in case the vehicle battery cable is disconnected.

The main body ECU (multiplex network body ECU) sends an arming signal to the theft warning siren assembly while transferring to the armed state, and it also sends a disarming signal to the siren while switching to the disarmed state. Also, the main body ECU (multiplex network body ECU) can cause the theft warning siren assembly to sound by sending an alarm signal during the alarm sounding state.

WIRING DIAGRAM

B427498E49
0.531,0.438 1.427,0.823 0.896,0.385 10 false from Battery 2.271,0.615 2.927,0.833 0.656,0.219 10 false S-HORN 3.292,1.688 4.542,2.094 1.25,0.406 10 false Theft Warning Siren Assembly 5.427,1.698 7.094,2.177 1.667,0.479 10 false Main Body ECU (Multiplex Network Body ECU) 3.302,1.531 3.76,1.729 0.458,0.198 10 false I68 5.427,1.521 5.885,1.719 0.458,0.198 10 false I2 4.25,0.76 4.865,0.958 0.615,0.198 10 false CONT 4.729,0.646 5.188,0.844 0.458,0.198 10 false 2 5.313,0.646 5.552,0.844 0.24,0.198 10 false 16 3.208,0.458 3.531,0.667 0.323,0.208 10 false +B 3.208,1.073 3.667,1.271 0.458,0.198 10 false GND 3.021,0.927 3.479,1.125 0.458,0.198 10 false 1 3.031,0.344 3.49,0.542 0.458,0.198 10 false 3 5.563,0.646 6.177,0.844 0.615,0.198 10 false SSCL

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

If the theft warning siren assembly is replaced, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SELF POWER SIREN)
a.

According to the display on the GTS, perform the Active Test.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Self Power Siren Theft warning siren assembly ON or OFF -
Body Electrical > Main Body > Active Test
Tester Display
Self Power Siren
50004 449 4
OK:

The theft warning siren assembly sounds and stops correctly when operated through the GTS.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the I68 theft warning siren assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I68)Location & Routing

Click Connector(I68)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Theft Warning Siren Assembly

I68-3 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I68)Location & Routing

Click Connector(I68)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Theft Warning Siren Assembly

I68-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the I68 theft warning siren assembly connector.


b.

Disconnect the I2 main body ECU (multiplex network body ECU) connector.



Result:
Proceed to
OK
NG



OK

4.CHECK THEFT WARNING SIREN ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK THEFT WARNING SIREN ASSEMBLY
a.

Temporarily replace the theft warning siren assembly with a new or normally functioning one.

HINT:

Refer to the Service Bulletin.



b.

Check the operation of the theft warning siren assembly function.

OK:

Theft warning siren assembly function operates normally.



Result:
Proceed to
OK
NG



OK

END (THEFT WARNING SIREN ASSEMBLY WAS DEFECTIVE)

NG