Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › PARK / NEUTRAL POSITION SWITCH
RM38G0E _52 Drivetrain _100436 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0468720 PARK / NEUTRAL POSITION SWITCH A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  PARK / NEUTRAL POSITION SWITCH  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C457857N01
3.917,3 5,3.167 1.083,0.167 4.667,2.667 5.417,2.833 0.75,0.167 1.5,3.417 2.333,3.583 0.833,0.167 4.625,2.625 5.458,2.875 0.833,0.25 3.875,2.958 5.042,3.208 1.167,0.25 1.583,3.083 1.917,3.083 1.917,3.083 1.917,2.542 false 2.5,1.167 2.833,1.167 2.833,1.167 3.479,2.063 false 2.854,2.646 3.333,3.333 3.333,3.333 3.5,3.333 false 4,2.469 4,2.75 4,2.75 4.417,2.75 false 1.583,1.917 2,1.917 false 3.146,2.479 3.583,3.083 3.583,3.083 3.917,3.083 false 2.469,3.271 2.469,3.5 2.469,3.5 2.333,3.5 false 1.354,2.948 1.688,3.365 0.333,0.417 18 false 3 3.542,3.188 3.875,3.604 0.333,0.417 18 false 2 2.26,1.01 2.594,1.427 0.333,0.417 18 false 1 1.417,1.833 1.583,2 0.167,0.167 10 false ● 4,3 5.167,3.167 1.167,0.167 8 false 6.9 (70, 61 in.*lbf) 4.719,2.667 5.635,2.833 0.917,0.167 8 false 12.8 (131, 9) 1.563,3.417 2.438,3.583 0.875,0.167 8 false 15.7 (160, 12) 4.448,2.667 4.615,2.833 0.167,0.167 10 false ★

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PARK/NEUTRAL POSITION SWITCH ASSEMBLY 84540 (Click here) - -
2 TRANSMISSION CONTROL SHAFT LEVER RH 35572 - - -
3 TRANSMISSION CONTROL CABLE ASSEMBLY 33820B (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
● Non-reusable part
V100135

Toyota Genuine Adhesive 1344
★ Precoated part - -

PROCEDURE

Hide 84540 1.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Z101186

HINT:

Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch assembly as the detent spring may become detached from the manual valve lever shaft.



a.
C455505C02
5.667,3.198 6.167,3 6.167,3 6.333,3 true 5.625,2.531 5.917,2.167 5.917,2.167 6.083,2.167 true 0.417,0.083 1.083,0.583 0.667,0.5 18 false i 4.167,0.083 4.75,0.417 0.583,0.333 18 true ii, iii 0.417,2.083 1,2.375 0.583,0.292 18 true iv, vi 4,2.083 4.583,2.417 0.583,0.333 18 true v 0.521,4.052 0.938,4.365 0.417,0.313 18 true vii 6.083,2.083 6.25,2.25 0.167,0.167 10 false *a 6.333,2.917 6.5,3.083 0.167,0.167 10 false *b 1.26,2.073 1.427,2.24 0.167,0.167 10 true N 4,4.083 4.417,4.375 0.417,0.292 18 true viii
*a Neutral Basic Line *b Groove


i.

Apply adhesive to threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



ii.

Temporarily install the park/neutral position switch assembly to the automatic transmission assembly with the bolt.

HINT:

Tighten the bolt to the specified torque when adjusting the park/neutral position switch assembly.



iii.

Install the lock washer and nut to the park/neutral position switch assembly.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


iv.

Temporarily install the transmission control shaft lever RH to the manual valve lever shaft with the spring washer and nut.


v.

Align the neutral basic line with the groove as shown in the illustration, and tighten the bolt.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


vi.

Turn the transmission control shaft lever RH clockwise until it stops, and then return the transmission control shaft lever RH counterclockwise 2 notches to N.


vii.

Using a screwdriver, bend the tabs of the lock washer.

NOTICE:
·

Be careful not to damage the park/neutral position switch assembly.

·

Bend at least 2 of the lock washer tabs.



HINT:

Tape the screwdriver tip before use.



viii.

Connect the park/neutral position switch assembly connector.



Hide 35572 2.INSTALL TRANSMISSION CONTROL SHAFT LEVER RH

Torque:
15.7 N*m (160 kgf*cm, 12 ft.*lbf)

Hide 33820B 3.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C456463C01
5,0.333 5.229,0.333 5.229,0.333 5.229,0.583 false 2,2.667 2.333,2.667 true 0.5,0 0.75,0.292 0.25,0.292 18 true i 0.5,2.083 0.75,2.375 0.25,0.292 18 true ii 4.833,0.25 5,0.417 0.167,0.167 10 false *a 4,2.469 4.167,2.635 0.167,0.167 10 false *b 2.333,2.583 2.5,2.75 0.167,0.167 10 true *a
*a Clip *b 45° to 60°
V113147

Install in this Direction - -


i.

While engaging the clip as shown in the illustration, connect the transmission control cable assembly to the transmission control shaft lever RH as shown in the illustration.

NOTICE:

Before installing the transmission control cable assembly, check that the park/neutral position switch assembly and shift lever are in N.



ii.

Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.