Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM38G0E _58 Vehicle Interior _100749 LIGHTING (INT) _0468730 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  IG Signal Circuit  


DESCRIPTION

This circuit detects the ignition switch ON or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E442534E04
5.708,0.948 6.167,1.146 0.458,0.198 10 false IGR 4.135,1 5.969,1.198 1.833,0.198 10 false ECU-IGR NO.2 3.438,1.802 5.271,2 1.833,0.198 10 false IGR-NO.2 2.75,0.833 3.063,1.031 0.313,0.198 10 false 5K 2.74,1.521 3.052,1.719 0.313,0.198 10 false 5B 2.75,2.135 3.063,2.333 0.313,0.198 10 false 5B 2.729,2.74 3.042,2.938 0.313,0.198 10 false 5C 2.781,0.604 2.938,0.802 0.156,0.198 10 false 1 5.708,2.115 6.167,2.313 0.458,0.198 10 false GND1 5.698,2.729 6.156,2.927 0.458,0.198 10 false GND2 5.344,0.708 5.656,0.906 0.313,0.198 10 false 27 5.385,2 5.698,2.198 0.313,0.198 10 false 13 5.365,2.615 5.677,2.813 0.313,0.198 10 false 14 5.292,3.594 6.927,3.948 1.635,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 5.292,3.458 5.688,3.74 0.396,0.281 10 false MB 3.052,3.417 4.49,3.802 1.438,0.385 10 false Power Distribution Box Assembly 2.74,1.281 3.052,1.479 0.313,0.198 10 false 27 2.74,1.896 3.052,2.094 0.313,0.198 10 false 36 2.729,2.521 3.042,2.719 0.313,0.198 10 false 41 0.885,0.823 2.719,1.021 1.833,0.198 10 false from Battery 0.292,1.51 1.677,2.073 1.385,0.563 10 false from Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CHECK FOR DTC (ENTRY AND START SYSTEM [for Start Function])
a.

Check for DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 454
OK:

Entry and start system (for Start Function) DTCs are not output.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

2.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IGR Power Ignition switch ON signal OFF or ON OFF: Ignition switch off
ON: Ignition switch ON
-
Body Electrical > Main Body > Data List
Tester Display
IGR Power
50003 449 122
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the 5B, 5C and 5K power distribution box assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5K-1 - Body ground Always 11 to 14 V
5B-27 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5B-36 - Body ground Always Below 1 Ω
5C-41 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK POWER DISTRIBUTION BOX ASSEMBLY
a.

Remove the power distribution box assembly.


E438202C08
1.74,0.25 2.177,0.552 0.438,0.302 5,0.24 5.438,0.542 0.438,0.302 4.99,2.146 5.427,2.448 0.438,0.302 1.75,2.063 2.188,2.365 0.438,0.302 4.833,3.281 4.99,3.281 4.99,3.281 5.135,2.906 true 6.313,3.313 6.469,3.313 6.469,3.313 6.615,2.938 true 4.844,3.552 5,3.552 5,3.552 5.229,2.938 true 1.875,0.313 2.188,0.51 0.313,0.198 10 false 5C 5.135,0.323 5.448,0.521 0.313,0.198 10 false 5B 5.115,2.219 5.427,2.417 0.313,0.198 10 false MB 1.875,2.125 2.188,2.323 0.313,0.198 10 false 5K 0.177,0.177 0.49,0.375 0.313,0.198 10 false *a 4.448,3.229 5.063,3.427 0.615,0.198 10 false GND1 4.458,3.49 5.073,3.688 0.615,0.198 10 false GND2 6.073,3.25 6.688,3.448 0.615,0.198 10 false IGR
*a Component without harness connected
(Power Distribution Box Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5C-41 - MB-13 (GND1) Always Below 1 Ω
5B-36 - MB-14 (GND2) Always Below 1 Ω
MB-27 (IGR) - 5K-1 Battery not connected to 5B-27 and 5B-36 10 kΩ or higher
Battery positive (+) → 5B-27
Battery negative (-) → 5B-36
Below 1 Ω
MB-13 (GND1) - 5B-36 Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

D

REPLACE POWER DISTRIBUTION BOX ASSEMBLY