When the battery saving control operates, the main body ECU (multiplex network body ECU) controls the operation of the DOME CUT relay that is built into the power distribution box assembly to turn off the interior lights.
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Check the vehicle condition.
| Result | Proceed to |
|---|---|
| All interior illumination supplied power to by DOME CUT relay does not turn on. | A |
| All interior illumination supplied power to by DOME CUT relay does not turn off. | B |
A
B
*1: w/ Map Light
*2: w/o Map Light
*3: for LED Type
*4: for Bulb Type
*5: w/ Courtesy Light
*6: w/ Scuff plate Light
*7: w/ Step Light
Disconnect the d1 map light assembly connector.*1
Disconnect the d10 No. 1 room light assembly connector.*2
Disconnect the d17 No. 2 room light assembly connector.*2
Disconnect the N9*3, N10*4 courtesy light assembly connector.*5
Disconnect the M11*3, M12*4 courtesy light assembly connector.*5
Disconnect the P6*3, P7*4 courtesy light assembly connector.*5
Disconnect the O6*3, O7*4 courtesy light assembly connector.*5
Disconnect the S32 front door scuff plate LH connector.*6
Disconnect the Q55 front door scuff plate RH connector.*6
Disconnect the d5*3, d9*4 vanity light assembly LH connector.
Disconnect the d4*3, d8*4 vanity light assembly RH connector.
Disconnect the U2*1, U3*3 No. 1 luggage compartment light assembly connector.
Disconnect the S17 step light assembly LH connector.*7
Disconnect the Q25 step light assembly RH connector.*7
Disconnect the 5C and5F power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(d9,O7)Location & Routingewd_type=routing;type=c,c;code=d9,O7 Click Connector(d9)Body>No. 1 Roof Wire>Vanity Light Assembly LHewd_type=component;type=c;code=d9;pinno=2 Click Connector(O7)Body>No. 1 Rear Door Wire>Rear Courtesy Light Assembly RHewd_type=component;type=c;code=O7;pinno=2 |
||
| d9-2 (B) - 5C-4 | Always | Below 1 Ω |
| O7-2 (B) - 5F-20*5 | Always | Below 1 Ω |
| d9-2 (B) or 5C-4- Body ground | Always | 10 kΩ or higher |
| O7-2 (B) or 5F-20 - Body ground*5 | Always | 10 kΩ or higher |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(d5,O6)Location & Routingewd_type=routing;type=c,c;code=d5,O6 Click Connector(d5)Body>No. 1 Roof Wire>Vanity Light Assembly LHewd_type=component;type=c;code=d5;pinno=1 Click Connector(O6)Body>No. 1 Rear Door Wire>Rear Courtesy Light Assembly RHewd_type=component;type=c;code=O6;pinno=1 |
||
| d5-1 (B) - 5C-4 | Always | Below 1 Ω |
| O6-1 (B) - 5F-20*5 | Always | Below 1 Ω |
| d5-1 (B) or 5C-4 - Body ground | Always | 10 kΩ or higher |
| O6-1 (B) or 5F-20 - Body ground*5 | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Power Distribution Box Assembly) |
Disconnect the power distribution box assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5H-1 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power distribution box assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected (Power Distribution Box Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5C-4 - 5H-1 | Battery not connected to 5H-1 and MB-17 (DOMR) | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5C-4 - Battery negative (-) terminal | Battery positive (+) → 5H-1 Battery negative (-) → MB-17 (DOMR) |
11 to 14 V |
| Battery not connected to 5H-1 and MB-17 (DOMR) | Below 1 V |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Relay for Interior Light Auto Cut Function | DOME CUT relay | OFF or ON | When performing this Active Test, turn all the interior lights on.
·
OFF: DOME CUT relay on (interior lights turn on)
·
ON: DOME CUT relay off (interior lights turn off) |
| Tester Display |
|---|
| Relay for Interior Light Auto Cut Function |
All of the interior lights turn off when ON is selected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power distribution box assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected (Power Distribution Box Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5C-4 - 5H-1 | Battery not connected to 5H-1 and MB-17 (DOMR) | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5C-4 - Battery negative (-) terminal | Battery positive (+) → 5H-1 Battery negative (-) → MB-17 (DOMR) |
11 to 14 V |
| Battery not connected to 5H-1 and MB-17 (DOMR) | Below 1 V |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D