Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Headlight ECU) › 2021.04–2022.11
RM38G0E _59 Vehicle Exterior _100649 LIGHTING (EXT) _0468731 LIGHTING SYSTEM(w/ Headlight ECU) C

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Headlight ECU)  B242E14  IG Circuit Short to Ground or Open  


DESCRIPTION

The headlight ECU sub-assembly operates using the power source voltage input from the IGR terminal and ECUB terminal.

The IGR terminal power source voltage is supplied by turning the IGR NO. 1 relay to ON.

The headlight ECU sub-assembly receives ignition switch ON signals from the main body ECU (multiplex network body ECU) via CAN communication, compares the ignition switch ON signal and the power source voltage supply condition of the IGR terminal and monitors the result.

Headlight Control
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B242E14 IG Circuit Short to Ground or Open
Detection condition:

The ignition switch is ON.


Malfunction status:

When the IGR terminal power source voltage is 0 V (ignition switch off), ignition switch ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received


Malfunction duration:

10 seconds or more


·

Headlight ECU sub-assembly LH

·

Harness or connector


Headlight Control A

Headlight Control (Sub)
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B242E14 IG Circuit Short to Ground or Open
Detection condition:

The ignition switch is ON.


Malfunction status:

When the IGR terminal power source voltage is 0 V (ignition switch off), ignition switch ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received


Malfunction duration:

10 seconds or more


·

Headlight ECU sub-assembly RH

·

Harness or connector


Headlight Control (Sub) A

WIRING DIAGRAM

E370857E42
0.229,0.708 2.219,0.906 1.99,0.198 10 false from IGR NO. 3 Relay 2.438,0.885 3.5,1.167 1.063,0.281 10 false ENG-IGR NO. 3 4.667,1.885 5.104,2.125 0.438,0.24 10 false B4 4.656,4.073 5.063,4.313 0.406,0.24 10 false B7 4.667,2.052 7.073,2.406 2.406,0.354 10 false Headlight ECU Sub-assembly LH 4.656,4.24 7.115,4.479 2.458,0.24 10 false Headlight ECU Sub-assembly RH 4.99,0.604 5.198,0.854 0.208,0.25 10 false 6 5,2.833 5.208,3.083 0.208,0.25 10 false 6 5.188,0.729 5.51,0.969 0.323,0.24 10 false IGR 5.188,2.948 5.51,3.177 0.323,0.229 10 false IGR 4.948,1.25 5.156,1.5 0.208,0.25 10 false 12 4.938,3.469 5.146,3.719 0.208,0.25 10 false 12 5.177,1.354 5.552,1.615 0.375,0.26 10 false GND 5.177,3.563 5.552,3.823 0.375,0.26 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>REGISTRATION

·

When replacing the headlight ECU sub-assembly LH, always replace it with a new one. If a headlight ECU sub-assembly LH which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242E14 is not output A
B242E14 is output B



Post-procedure1

d.

None



A

3.CLEAR DTC

B

7.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)
3.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control (Sub) > Clear DTCs
50002 463

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control (Sub) > Trouble Codes
50001 463
Result:
Result Proceed to
B242E14 is not output A
B242E14 is output B



Post-procedure1

d.

None



A

B

5.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)
5.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)

Pre-procedure1

a.

Disconnect the B7 headlight ECU sub-assembly RH connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B7)Location & Routing

Click Connector(B7)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

B7-6 (IGR) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

6.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B7)Location & Routing

Click Connector(B7)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

B7-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)

Pre-procedure1

a.

Disconnect the B4 headlight ECU sub-assembly LH connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B4)Location & Routing

Click Connector(B4)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

B4-6 (IGR) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B4)Location & Routing

Click Connector(B4)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

B4-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR