Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM
RM38G0E _52 Drivetrain _100436 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0468743 AUTOMATIC TRANSMISSION SYSTEM C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P27137F  Pressure Control Solenoid "D" Actuator Stuck Off  


DESCRIPTION

The shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle speed sensor. The ECM adjusts the current to shift solenoid valve SLT to control hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

C318298E01
1.573,0.208 1.802,0.208 1.802,0.208 2.281,0.771 true 1.604,1.313 1.833,1.313 1.833,1.313 2.198,0.938 true 3.604,0.26 3.323,0.26 3.323,0.26 3.219,0.635 true 1.146,1.219 2.063,1.417 0.917,0.198 10 false Sleeve 0.813,0.125 2.5,0.323 1.688,0.198 10 false Spool Valve 3.677,0.188 4.906,0.385 1.229,0.198 10 false Solenoid 4.479,0.635 5.073,1.031 0.594,0.396 10 false Hydraulic Pressure 5.698,1.438 6.771,1.635 1.073,0.198 10 false Current

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P27137F Pressure Control Solenoid "D" Actuator Stuck Off The ECM detects a malfunction in the shift solenoid valve SLT (ON side) according to the difference in the speed between the turbine and the output shaft, and also by the ATF pressure. (2 trip detection logic)
·

Shift solenoid valve SLT remains open

·

Shift solenoid valve SL1, SL2, SL3 or SL4 remains open or closed

·

Transmission valve body assembly is blocked

·

Automatic transmission assembly (clutch, brake or gear, etc.)


Comes on DTC stored SAE Code:
P2714

MONITOR DESCRIPTION

The ECM calculates the amount of clutch slip based on the input turbine speed, output shaft speed, and gear ratio. If the amount of clutch slip exceeds a specified level, the ECM will set this DTC and illuminate the MIL.

When shift solenoid valve SLT remains on, the line pressure goes down and clutch engagement force decreases.

NOTICE:

If the vehicle continues to be driven under these conditions, the clutch will burn up and the vehicle will no longer be drivable.


CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Start the engine.

4.
5.

Stop the vehicle.

6.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

7.

Input the DTC: P27137F.

8.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P27137F)
a.

Read the DTCs using the GTS.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
Only DTC P27137F is output A
P27137F and other DTCs are output B


HINT:

If a solenoid is stuck on, DTCs for several solenoids including the malfunctioning solenoid will be detected.




A

4.INSPECT SHIFT SOLENOID VALVE SLT

B

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE SOLENOID (SLT))
2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE SOLENOID (SLT))
NOTICE:
·

Perform the test while the ATF (Automatic Transmission Fluid) temperature is between 50 and 80°C (122 and 176°F).

·

Be careful to prevent the hose of SST from interfering with the exhaust pipe.

·

This check must be conducted after checking and adjusting the engine.

·

Perform the test with the air conditioning off.



HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Turn the ignition switch off.


b.

Lift the vehicle.


c.
C457091E01
0.74,0.396 1.104,0.292 false 1.177,0.208 1.635,0.406 0.458,0.198 10 false SST 2.229,0.688 2.688,0.885 0.458,0.198 10 false SST

Remove the test plug from the transmission case and connect SST.


SST
09993-19015  (09993-00010, 09993-00040)

d.

Lower the vehicle.


e.

Fully apply the parking brake and chock the 4 wheels.


f.

Start the engine.


g.

Warm up the ATF (Automatic Transmission Fluid).


h.

Measure the line pressure when the engine is idling.


i.

Perform the Active Test according to the display on the GTS.


j.

Measure the line pressure with SST.

Powertrain > Engine > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the Solenoid (SLT) Operates shift solenoid valve SLT to raise the line pressure. ON/OFF
HINT:

ON: No action (normal operation)

OFF: Line pressure up (When the Active Test of "Activate the Solenoid (SLT)" is performed, the ECM commands the shift solenoid valve SLT to turn off).


[Vehicle Condition]
·

Vehicle stopped

·

Engine idling


Powertrain > Engine > Active Test
Tester Display
Activate the Solenoid (SLT)
50004 372 14

The "Activate the solenoid (SLT)" Active Test is performed to allow confirmation that the line pressure changes. The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test

Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>HYDRAULIC TEST

HINT:

Note that the pressure readings for the Active Test and Hydraulic Test are different.


OK:

The line pressure changes as specified when performing the Active Test.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (CONTROL THE SHIFT POSITION)

NG

4.INSPECT SHIFT SOLENOID VALVE SLT
3.PERFORM ACTIVE TEST USING GTS (CONTROL THE SHIFT POSITION)
NOTICE:

This test should always be performed with at least 2 people.


a.

Warm up the engine.


b.

Perform the Active Test according to the display on the GTS.

HINT:

Comparing the gear commanded by the Active Test with the actual gear enables confirmation of the problem.

Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>FAIL-SAFE CHART


Powertrain > Engine > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Control the Shift Position Operates the shift solenoid valves to allow gears to be selected manually. 1st/2nd/3rd/4th/5th/6th
Start/Stop
Can be used to check the operation of the shift solenoid valves.
Up-shifts and down-shifts should be performed consecutively. A 10 second interval is required between gear changes.
Do not down-shift at high speeds. Doing so will damage the automatic transmission.
[Vehicle Condition]

50 km/h (31 mph) or less


Powertrain > Engine > Active Test
Tester Display
Control the Shift Position
50004 372 42009
HINT:
·

This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.

·

The 4th to 5th and 5th to 6th up-shift must be performed with the accelerator pedal released.

·

The 6th to 5th and 5th to 4th down-shift must be performed with the accelerator pedal released.

·

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

·

The gear commanded by the ECM is shown in the Data List / Shift Status display on the GTS.




c.

Compare the ECM commanded gear and actual gear.

Result:
Actual Gear during Malfunction ECM Commanded Gear Proceed to
1st 2nd 3rd 4th 5th 6th
Shift solenoid valve SL1 Stuck ON 1st 2nd 3rd 4th 4th 4th A
Stuck OFF N*1 N*1 N*1 N*1 5th 6th
Shift solenoid valve SL2 Stuck ON 4th 4th 4th 4th 5th 6th B
Stuck OFF 1st 2nd 3rd 1st N*1 N*1
Shift solenoid valve SL3 Stuck ON 2nd 2nd 3rd 4th 5th 6th C
Stuck OFF 1st 1st 3rd 4th 5th N*1
Shift solenoid valve SL4 Stuck ON 3rd 3rd 3rd 4th 5th 5th D
Stuck OFF 1st 2nd 1st 4th N*1 6th
Shift solenoid valve SLT Stuck ON N*2 N*2 N*2 N*2 N*2 N*2 E
Stuck OFF*3 1st 2nd 3rd 4th 5th 6th


HINT:
·

*1: Neutral

·

*2: If shift solenoid valve SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is lower than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.

·

*3: When shift solenoid valve SLT is stuck off, gear shifting is normal.





A

GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE SL1 PERFORMANCE DTC P07457F)

B

GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE SL2 PERFORMANCE DTC P07757F)

C

GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE SL3 PERFORMANCE DTC P07957F)

D

GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE SL4 PERFORMANCE DTC P28077F)

E

4.INSPECT SHIFT SOLENOID VALVE SLT
4.INSPECT SHIFT SOLENOID VALVE SLT
a.
C201747C22
1.5,0.854 0.646,0.625 false 1.781,0.844 2.479,0.604 false 1.51,3.135 0.656,2.906 false 1.781,3.115 2.479,2.875 false 0.49,0.521 0.667,0.719 0.177,0.198 10 false 2 2.531,0.5 2.708,0.698 0.177,0.198 10 false 1 1.198,4.208 1.406,4.417 0.208,0.208 10 false (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 false (+) 0.49,2.771 0.667,2.969 0.177,0.198 10 false 2 2.531,2.771 2.708,2.969 0.177,0.198 10 false 1 0.135,0.083 0.354,0.292 0.219,0.208 10 false *1
*1 Shift Solenoid Valve SLT


Remove shift solenoid valve SLT.

Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL

OK:

There is no foreign matter on each valve and they operate smoothly.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY