Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY
RM38G0E _52 Drivetrain _100436 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0468725 AUTOMATIC TRANSMISSION ASSEMBLY A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C456840N01
4.167,4.75 4.417,4.5 4.417,4.5 4.583,4.5 false 1.583,4.333 1.583,4.75 1.583,4.75 1.75,4.75 false 6,2.5 6,2 6,2 6.167,2 false 4.583,3.417 4.583,2.917 4.583,2.917 4.417,2.917 false 5.333,3.583 5.333,4 5.333,4 5.5,4 false 4.167,5.25 4.5,5.083 4.5,5.083 4.833,5.083 false 6.417,0.167 6.75,0.167 false 4.615,4.333 5.031,4.75 0.417,0.417 18 false 1 1.792,4.594 2.292,5.01 0.5,0.417 18 false 2 6.208,1.854 6.708,2.271 0.5,0.417 18 false 3 4.073,2.771 4.573,3.188 0.5,0.417 18 false 4 5.542,3.833 6.042,4.25 0.5,0.417 18 false 5 4.865,4.917 5.281,5.333 0.417,0.417 18 false 6 3.229,5.479 3.688,5.677 0.458,0.198 10 false x 4 5.917,0 6.667,0.5 0.75,0.5 18 false 7, 8

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT PROPELLER SHAFT ASSEMBLY 37140 - - -
2 REAR PROPELLER SHAFT ASSEMBLY 37110F - - -
3 EXHAUST MANIFOLD ASSEMBLY LH 17150 - - -
4 EXHAUST MANIFOLD ASSEMBLY RH 17140 - - -
5 STARTER ASSEMBLY 28100 - - -
6 OIL PAN PROTECTOR ASSEMBLY 51440 - - -
7 DRAIN AUTOMATIC TRANSMISSION FLUID - - (Click here) -
8 DRAIN TRANSFER OIL - - (Click here) -

C456841N01
6.083,3.5 5.833,3.5 5.833,3.5 5.833,4.146 false 1.833,1.75 1.583,1.75 1.583,1.75 1.583,1.469 false 5.667,1.167 5.417,1.167 5.417,1.167 5.417,1.521 false 2.5,4.417 2.75,4.417 2.75,4.417 2.75,4.188 false 0.75,2.333 0.5,2.333 0.5,2.333 0.5,3 false 2.99,2.188 3.573,1.771 3.573,1.771 3.906,1.771 false 4.667,4.083 4.833,3.75 4.833,3.75 5.083,3.75 false 5.146,5 5.583,5 false 1.833,2.833 2.083,2.833 2.083,2.833 2.083,3.417 false 5.542,2.75 5.958,2.75 false 6.5,3.281 6.833,3.698 0.333,0.417 18 false 9 2.229,1.604 2.896,2.104 0.667,0.5 18 false 10 5.708,1 6.375,1.5 0.667,0.5 18 false 11 2.156,4.271 2.823,4.771 0.667,0.5 18 false 12 1.25,2.083 1.917,2.583 0.667,0.5 18 false 14 6.333,2.583 7,3.083 0.667,0.5 18 false 15 5.646,4.854 6.313,5.354 0.667,0.5 18 false 16 5.125,3.583 5.792,4.083 0.667,0.5 18 false 18 5.042,4.406 5.375,4.573 0.333,0.167 10 false x 4 4.802,5.292 5.135,5.458 0.333,0.167 10 false x 4 0.458,3.094 0.792,3.26 0.333,0.167 10 false *a 1.5,2.667 2.167,3.167 0.667,0.5 18 false 13 4.417,4.406 4.75,4.573 0.333,0.167 10 false x 4 3.583,4.625 3.917,4.792 0.333,0.167 10 false x 4 4.25,1.625 4.917,2.125 0.667,0.5 18 false 17

Procedure Part Name Code
Z101186

Z101188

Z101187

9 TRANSMISSION CONTROL CABLE ASSEMBLY 33820B (Click here) - -
10 OIL COOLER TUBE - (Click here) - -
11 DISCONNECT WIRE HARNESS CLAMP BRACKET - - - -
12 FLYWHEEL HOUSING UNDER COVER 11361J - - -
13 FLYWHEEL HOUSING SIDE COVER 11363A - - -
14 DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT - (Click here) - -
15 SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY 35000 (Click here) - -
16 NO. 3 FRAME CROSSMEMBER ASSEMBLY - - - -
17 TRANSMISSION BREATHER HOSE ASSEMBLY - (Click here) - -
18 REAR ENGINE MOUNTING INSULATOR 12371A - - -

*a BLACK: x 1
SILVER: x 5
- -

C456842N01
3.5,4.417 3.5,4.917 3.5,4.917 3.833,4.917 false 2.583,2.323 2.583,1.917 2.583,1.917 2.833,1.917 false 4.167,1 4.167,0.417 4.167,0.417 4.333,0.417 false 5.667,3.667 6,3.333 6,3.333 6.281,3.333 false 4.188,4.771 5.354,5.188 1.167,0.417 18 false 21 2.885,1.76 3.385,2.177 0.5,0.417 18 false 19 4.729,0.26 5.229,0.677 0.5,0.417 18 false 20 6.625,3.167 7.125,3.583 0.5,0.417 18 false 22 2.125,3.052 2.583,3.25 0.458,0.198 10 false x 5 2.125,5.25 2.583,5.448 0.458,0.198 10 false x 4 4.854,2.99 5.313,3.188 0.458,0.198 10 false x 5

Procedure Part Name Code
Z101186

Z101188

Z101187

19 TRANSFER BREATHER HOSE SUB-ASSEMBLY 36407 - - -
20 ENGINE WIRE 82121 (Click here) - -
21 AUTOMATIC TRANSMISSION ASSEMBLY 35000 (Click here) - -
22 TRANSFER ASSEMBLY 36100 (Click here) - -

C456843N01
3.333,1.5 3.75,1.5 false 4.917,2.083 5.25,2.083 false 5.167,4.667 5.417,4.667 5.417,4.667 5.417,4.375 false 1.75,1.667 1.75,0.917 1.75,0.917 2,0.917 false 1.583,4.438 1.583,4.833 1.583,4.833 1.833,4.833 false 6.167,3.708 6.167,3.25 6.167,3.25 6.333,3.25 false 0.917,2.833 1.083,2.833 1.083,2.833 1.125,2.49 false 6.333,0.167 6.75,0.167 false 3.833,1.333 4.333,1.917 0.5,0.583 18 false 23 5.333,1.917 5.833,2.5 0.5,0.583 18 false 23 4.833,4.5 5.333,5.083 0.5,0.583 18 false 23 2.042,0.75 2.542,1.333 0.5,0.583 18 false 24 2.177,4.677 3.25,5.25 1.073,0.573 18 false 26, 27 0.542,2.667 1.042,3.167 0.5,0.5 18 false 25 6.417,3.083 6.823,3.583 0.406,0.5 18 false 25 6,0 6.5,0.583 0.5,0.583 18 false 28 1.281,1.563 1.615,1.729 0.333,0.167 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

23 WIRE HARNESS CLAMP BRACKET - - - -
24 NO. 1 TRANSMISSION CONTROL CABLE BRACKET 33823 - - -
25 EXHAUST SENSOR CLAMP BRACKET 8946A - - -
26 REMOVE TORQUE CONVERTER ASSEMBLY 32000 (Click here) - -
27 INSPECT TORQUE CONVERTER ASSEMBLY 32000 (Click here) - -
28 INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY 32101 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the automatic transmission assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
Automatic transmission assembly Reset memory
·

Large shift shock

·

Engine overruns


(Click here)
Automatic transmission fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly.
Gas leaks from exhaust system Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
C344337

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

·
C313282C13
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Object Exceeding Weight Limit of Transmission Jack


The automatic transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.



HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 37140 1.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 37110F 2.REMOVE REAR PROPELLER SHAFT ASSEMBLY

Hide 17150 3.REMOVE EXHAUST MANIFOLD ASSEMBLY LH

Hide 17140 4.REMOVE EXHAUST MANIFOLD ASSEMBLY RH

Hide 28100 5.REMOVE STARTER ASSEMBLY

Hide 51440 6.REMOVE OIL PAN PROTECTOR ASSEMBLY

a.
C456844


Hide 7.DRAIN AUTOMATIC TRANSMISSION FLUID

Z101186

Click here(Click here)

Hide 8.DRAIN TRANSFER OIL

Z101186

Click here(Click here)

Hide 33820B 9.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Z101186

Click here(Click here)

Hide 10.DISCONNECT OIL COOLER TUBE

a.
C456845N01
0.354,0 1.156,0.563 0.802,0.563 18 false i - iii

i.

Disconnect the 2 oil cooler tubes from the automatic transmission assembly.

HINT:

Use a container to catch any ATF which flows out of the 2 oil cooler tubes and automatic transmission assembly.



ii.

Remove the 2 bolts and disconnect the 2 oil cooler tubes from the 2 oil cooler tube clamps.


iii.

Remove the 2 bolts and 2 oil cooler tube clamps from the automatic transmission assembly and engine assembly.

HINT:

It is not necessary to remove the oil cooler tube clamps unless they are being replaced.




Hide 11.DISCONNECT WIRE HARNESS CLAMP BRACKET

Hide 11361J 12.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
C456847


Hide 11363A 13.REMOVE FLYWHEEL HOUSING SIDE COVER

a.
C458211


Hide 14.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

a.
C456848N02
1.833,0.042 2.083,0.458 0.25,0.417 18 false i

i.

Turn the crankshaft to gain access to the removable locations of the 6 drive plate and torque converter assembly setting bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored bolt.




Hide 35000 15.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

a.
C456849N01
1.917,0.021 2.25,0.438 0.333,0.417 18 false i

i.

Support the automatic transmission assembly with a transmission jack.

NOTICE:
·

In order to protect the automatic transmission oil pan sub-assembly, place attachments on the transmission jack.

·

Make sure that the attachments and the automatic transmission oil pan sub-assembly are centered on the transmission jack.

·

To prevent the automatic transmission oil pan sub-assembly from deforming, do not place any attachments under the automatic transmission oil pan sub-assembly of the automatic transmission assembly.

·

Secure the automatic transmission assembly to the transmission jack using a belt, etc. to prevent it from falling.





Hide 16.REMOVE NO. 3 FRAME CROSSMEMBER ASSEMBLY

Hide 17.REMOVE TRANSMISSION BREATHER HOSE ASSEMBLY

a.
C456852C01
0.396,0.042 0.646,0.542 0.25,0.5 18 false i 3.792,0.042 4.042,0.542 0.25,0.5 18 false ii
V113147

Tilt Down - -


i.

Tilt down the automatic transmission assembly.

NOTICE:

Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.



ii.

Disconnect the breather hose and detach the wire harness clamp from the transmission breather bracket.



Hide 12371A 18.REMOVE REAR ENGINE MOUNTING INSULATOR

Hide 36407 19.REMOVE TRANSFER BREATHER HOSE SUB-ASSEMBLY

a.
C456855


Hide 82121 20.DISCONNECT ENGINE WIRE

a.
C456853C02
0.417,0 0.75,0.5 0.333,0.5 18 false i
V113147

Pull Down the Lever - -


i.

Detach the clamp and disconnect the 8 engine wire connectors from the automatic transmission assembly with transfer assembly.

HINT:

Detach the claw, pull down the lever, and disconnect the transmission wire connector.




Hide 35000 21.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

a.
C456854N01
1.917,0.021 2.219,0.406 0.302,0.385 18 false i

i.

Remove the 9 bolts and automatic transmission assembly from the engine assembly.

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the automatic transmission assembly and engine assembly.




Hide 36100 22.REMOVE TRANSFER ASSEMBLY

Z101186

Click here(Click here)

Hide 23.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C456856

HINT:

It is not necessary to remove the wire harness clamp brackets unless they are being replaced.



Hide 33823 24.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C456857

HINT:

It is not necessary to remove the No. 1 transmission control cable bracket unless it is being replaced.



Hide 8946A 25.REMOVE EXHAUST SENSOR CLAMP BRACKET

a.
C458212

HINT:

It is not necessary to remove the exhaust sensor clamp bracket unless it is being replaced.



Hide 32000 26.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C456858C01
3.583,0.417 4.25,0.25 true 3.583,0.167 4.25,0.25 true 2.271,0.031 2.938,0.615 0.667,0.583 18 false i, ii 4.281,0.167 4.448,0.333 0.167,0.167 10 false *a
*a Matchmark - -


i.

Put matchmarks on the automatic transmission assembly and the torque converter assembly.


ii.

Remove the torque converter assembly from the automatic transmission assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.




Hide 32000 27.INSPECT TORQUE CONVERTER ASSEMBLY

Z101186

Click here(Click here)

Hide 32101 28.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Z101186

Click here(Click here)