Home › Audio / Visual / Telematics › AUDIO / VIDEO › ACTIVE NOISE CONTROL SYSTEM (for Type A)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467499 ACTIVE NOISE CONTROL SYSTEM(for Type A) C

AUDIO / VIDEO  ACTIVE NOISE CONTROL SYSTEM(for Type A)  P033531  Crankshaft Position Sensor "A" No Signal  


DESCRIPTION

This DTC is output when a malfunction has occurred in the engine pulse signal system from the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
P033531 Crankshaft Position Sensor "A" No Signal Engine started, engine speed is 500 rpm or higher and below 6000 rpm 3 seconds after the ignition switch is turned to ACC, the stereo component equalizer assembly detects a malfunction in the engine pulse signal system for 10 seconds or more continuously*
·

Harness or connector

·

ECM

·

Stereo component equalizer assembly


Active Noise Control A

HINT:

*: Malfunction monitoring is not performed during the following conditions to prevent erroneous detection.

·

The battery voltage is less than 9.5 V.

·

Before 3 seconds have elapsed after the battery voltage has returned to normal.



WIRING DIAGRAM

E385046E07
1.021,1.167 1.479,1.365 0.458,0.198 10 false NEO 1.417,1.063 1.74,1.281 0.323,0.219 10 false 31 0.417,1.802 0.896,2.031 0.479,0.229 10 false B1 0.417,1.969 0.875,2.167 0.458,0.198 10 false ECM 5.771,1.177 6.229,1.375 0.458,0.198 10 false NEI 5.563,1.042 5.719,1.229 0.156,0.188 10 false 3 5.708,1.792 6.167,1.99 0.458,0.198 10 false S20 5.698,1.958 6.958,2.365 1.26,0.406 10 false Stereo Component Equalizer Assembly 2.167,0.375 3.542,0.635 1.375,0.26 10 false from Other Systems

CAUTION / NOTICE / HINT

NOTICE:

The active noise control system troubleshooting procedure is based on the premise that the stop and start system*, SFI system and entry and start system is operating normally. Check the stop and start system*, SFI system and entry and start system first before troubleshooting the active noise control system.

*: w/ Stop and Start System


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Active Noise Control > Clear DTCs
50002 415
Result:
Proceed to
NEXT




NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Active Noise Control > Trouble Codes
50001 415
Result:
Result Proceed to
P033531 is not output. A
P033531 is output. B




A

B

3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the S20 stereo component equalizer assembly connector.


b.

Disconnect the B1 ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(S20,B1)Location & Routing

Click Connector(S20)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assembly

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

S20-3 (NEI) - B1-31 (NEO) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE STEREO COMPONENT EQUALIZER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR