Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467497 AUDIO AND VISUAL SYSTEM(for Radio and Display Type, except 12.3 Inch Display) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type, except 12.3 Inch Display)  Mute Signal Circuit between Radio Receiver and Stereo Component Equalizer  


DESCRIPTION

The telephone transceiver assembly sends a mute signal to the stereo component equalizer assembly.

The stereo component equalizer assembly controls the volume according to the mute signal from the telephone transceiver assembly.

WIRING DIAGRAM

E464749E07
1,1.531 1.458,1.729 0.458,0.198 10 false S25 1,1.729 2.781,2.146 1.781,0.417 10 false Stereo Component Equalizer Assembly 5.063,0.823 5.302,1.031 0.24,0.208 10 false 3 2,0.813 2.229,1 0.229,0.188 10 false 19 1.521,0.927 1.979,1.125 0.458,0.198 10 false TMU1 5.292,0.896 5.781,1.094 0.49,0.198 10 false TMUT 4.99,1.531 5.448,1.729 0.458,0.198 10 false I13 5,1.719 6.708,2.281 1.708,0.563 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>PRECAUTION


PROCEDURE

1.CHECK STEREO COMPONENT EQUALIZER ASSEMBLY
a.
E464178C02
1.469,0.563 1.938,0.865 0.469,0.302 2.5,1.833 2.5,2.5 2.5,2.5 2.667,2.5 true 1.563,0.635 2.417,1.104 0.854,0.469 10 false S25 2.75,2.417 3.24,2.615 0.49,0.198 10 false TMU1 0.219,0.188 0.531,0.385 0.313,0.198 10 false *a
*a Component with harness connected
(Stereo Component Equalizer Assembly)


Remove the stereo component equalizer assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>ACTIVE NOISE CONTROL ECU>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(S25)Location & Routing

Click Connector(S25)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assembly

S25-19 (TMU1) - Body ground Ignition switch ON
Audio system playing
→ Emergency call mode
2.0 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the I13 radio and display receiver assembly connector.


b.

Disconnect the S25 stereo component equalizer assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(S25,I13)Location & Routing

Click Connector(S25)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assembly

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

S25-19 (TMU1) - I13-3 (TMUT) Always Below 1 Ω
S25-19 (TMU1) or I13-3 (TMUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the S25 stereo component equalizer assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I13)Location & Routing

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I13-3 (TMUT) - Body ground Ignition switch ACC 2.0 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT EQUALIZER ASSEMBLY

NG