Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display) › 2021.04–2021.07
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467497 AUDIO AND VISUAL SYSTEM(for Radio and Display Type, except 12.3 Inch Display) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type, except 12.3 Inch Display)  Microphone Circuit  


DESCRIPTION

The radio and display receiver assembly, telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

WIRING DIAGRAM

E464168E02
5.76,1.365 6.375,1.563 0.615,0.198 10 false SNS2 1.625,1.375 2.042,1.573 0.417,0.198 10 false SNS2 1.604,1.781 2.063,1.958 0.458,0.177 10 false MACC 1.625,2.115 2.083,2.292 0.458,0.177 10 false MCO+ 1.677,2.438 2.135,2.615 0.458,0.177 10 false MCO- 5.781,1.771 6.24,1.948 0.458,0.177 10 false MACC 5.771,2.104 6.146,2.333 0.375,0.229 10 false MIN+ 5.771,2.458 6.146,2.688 0.375,0.229 10 false MIN- 5.771,2.792 6.271,3.021 0.5,0.229 10 false SGND 3.792,2.729 4.292,2.958 0.5,0.229 10 false *1 0.333,4.021 1.74,4.479 1.406,0.458 10 false Telephone Microphone Assembly 0.333,3.854 1.969,4.083 1.635,0.229 10 false d28*2, d30*3 5.438,3.802 5.781,3.99 0.344,0.188 10 false I13 5.438,3.979 7.115,4.344 1.677,0.365 10 false Radio and Display Receiver Assembly 2.177,1.25 2.406,1.417 0.229,0.167 10 false 3 2.188,1.667 2.417,1.833 0.229,0.167 10 false 1 2.198,2 2.427,2.167 0.229,0.167 10 false 2 2.198,2.344 2.427,2.51 0.229,0.167 10 false 4 5.5,2.688 5.844,2.875 0.344,0.188 10 false 24 5.5,2.01 5.844,2.198 0.344,0.188 10 false 21 5.49,2.344 5.833,2.531 0.344,0.188 10 false 22 5.5,1.677 5.844,1.865 0.344,0.188 10 false 23 5.5,1.271 5.844,1.458 0.344,0.188 10 false 25 1.948,4.542 3.656,4.74 1.708,0.198 10 false *1: Shielded 2.969,4.542 4.677,4.74 1.708,0.198 10 false *2: for LHD 3.833,4.542 5.542,4.74 1.708,0.198 10 false *3: for RHD


CAUTION / NOTICE / HINT

NOTICE:

When replacing the telephone transceiver assembly, make sure to replace it with a new one. (w/ Telematics Transceiver)


HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>PRECAUTION


PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the I13 radio and display receiver assembly connector.


b.

Disconnect the d28*1 or d30*2 telephone microphone assembly connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(I13,d28)Location & Routing

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

Click Connector(d28)Body>No. 1 Roof Wire>Telephone Microphone Assembly LH

I13-25 (SNS2) - d28-3 (SNS2) Always Below 1 Ω
I13-23 (MACC) - d28-1 (MACC) Always Below 1 Ω
I13-21 (MIN+) - d28-2 (MCO+) Always Below 1 Ω
I13-22 (MIN-) - d28-4 (MCO-) Always Below 1 Ω
I13-25 (SNS2) - Body ground Always 10 kΩ or higher
I13-23 (MACC) - Body ground Always 10 kΩ or higher
I13-21 (MIN+) - Body ground Always 10 kΩ or higher
I13-22 (MIN-) - Body ground Always 10 kΩ or higher
I13-24 (SGND) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(I13,d30)Location & Routing

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

Click Connector(d30)Body>No. 1 Roof Wire>Telephone Microphone Assembly RH

I13-25 (SNS2) - d30-3 (SNS2) Always Below 1 Ω
I13-23 (MACC) - d30-1 (MACC) Always Below 1 Ω
I13-21 (MIN+) - d30-2 (MCO+) Always Below 1 Ω
I13-22 (MIN-) - d30-4 (MCO-) Always Below 1 Ω
I13-25 (SNS2) - Body ground Always 10 kΩ or higher
I13-23 (MACC) - Body ground Always 10 kΩ or higher
I13-21 (MIN+) - Body ground Always 10 kΩ or higher
I13-22 (MIN-) - Body ground Always 10 kΩ or higher
I13-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E464176C01
1.5,0.75 1.917,1 0.417,0.25 2.813,2.604 2.052,2.156 true 2.271,2.896 1.927,2.156 true 1.198,2.833 1.813,2.146 true 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.604,0.792 1.917,0.99 0.313,0.198 10 false I13 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN- 2.083,2.896 2.583,3.115 0.5,0.219 10 false MACC 1.01,2.854 1.625,3.052 0.615,0.198 10 false SGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Remove the radio and display receiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I13)Location & Routing

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I13-23 (MACC) - Body ground Ignition switch ACC 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I13)Location & Routing

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I13-24 (SGND) - Body ground Always Below 1 Ω
I13-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK TELEPHONE MICROPHONE ASSEMBLY (OUTPUT TO TELEPHONE TRANSCEIVER ASSEMBLY)

NG

4.CHECK TELEPHONE MICROPHONE ASSEMBLY (OUTPUT TO TELEPHONE TRANSCEIVER ASSEMBLY)
E456925C03
1.01,0.083 1.417,0.333 0.406,0.25 1.833,0.083 2.24,0.333 0.406,0.25 1.063,0.542 1.25,0.542 1.25,0.542 1.448,1.24 true 2.365,0.552 2.177,0.552 2.177,0.552 1.938,1.229 true 0.365,0.448 0.677,0.646 0.313,0.198 10 false *a 2.833,3.448 3.292,3.646 0.458,0.198 10 false GND 0.625,0.448 1.24,0.646 0.615,0.198 10 false MCO- 2.448,0.469 3.063,0.667 0.615,0.198 10 false MCO+ 1.448,0.115 1.813,0.313 0.365,0.198 10 false *A 1.094,0.125 1.458,0.323 0.365,0.198 10 false d28 2.302,0.115 2.667,0.313 0.365,0.198 10 false *B 1.927,0.115 2.292,0.313 0.365,0.198 10 false d30
*A for LHD
*B for RHD
*a Component with harness connected
(Telephone Microphone Assembly)


a.

Check the output waveform.

i.

Remove the telephone microphone assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL


ii.

Check the signal waveform according to the condition(s) in the table below.

Item Condition

*1: for LHD

*2: for RHD

Measurement terminal d28-2 (MCO+) - d28-4 (MCO-)*1
d30-2 (MCO+) - d30-4 (MCO-)*2
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Ignition switch ON

2.

Sound is input to the telephone microphone assembly when the user is closer than 125 mm (4.92 in.) from the telephone microphone assembly sound holes in the microphone case.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.




Result:
Proceed to
OK
NG



OK

NG