Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › TOYOTA MULTI OPERATION TOUCH SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100607 NAVIGATION / MULTI INFO DISPLAY _0467505 TOYOTA MULTI OPERATION TOUCH SYSTEM Y

NAVIGATION / MULTI INFO DISPLAY  TOYOTA MULTI OPERATION TOUCH SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the toyota multi operation touch system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
·

When troubleshooting, check that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms


Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY
3.INSPECT BATTERY
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


HINT:

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.



Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Result:
Result Proceed to
CAN DTCs are not output. A
CAN DTCs are output. B




A

5.CHECK FOR DTC*

B

5.CHECK FOR DTC*
Body Electrical > D-SEAT SW > Trouble Codes
50001 181
Result:
Result Proceed to
DTCs are output. A
DTCs are not output. B



A

6.DTC CLEAR*

B

9.PROBLEM SYMPTOMS TABLE
6.DTC CLEAR*
Body Electrical > D-SEAT SW > Clear DTCs
50002 181
HINT:

The present DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.


Result:
Proceed to
NEXT



NEXT

7.RECHECK FOR DTC*
7.RECHECK FOR DTC*
Body Electrical > D-SEAT SW > Trouble Codes
50001 181
Result:
Result Proceed to
DTCs are output. A
DTCs are not output. B


HINT:
·

Even if the problem symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.

·

If more information is needed, perform a recheck using the "System Check Mode" screen after rechecking for DTCs using the GTS.

·

Check for DTCs and inspect the area that the code indicates.




A

8.DIAGNOSTIC TROUBLE CODE CHART

B

9.PROBLEM SYMPTOMS TABLE
8.DIAGNOSTIC TROUBLE CODE CHART

Result:
Proceed to
NEXT



NEXT

11.CHECK CIRCUIT
9.PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>TOYOTA MULTI OPERATION TOUCH SYSTEM>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table. A
Fault is listed in Problem Symptoms Table. B


HINT:

If the symptoms do not recur and no DTCs are output, attempt to reproduce the symptoms.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING




A

10.PERFORM TROUBLESHOOTING BASED ON PROBLEM SYMPTOM

B

11.CHECK CIRCUIT
10.PERFORM TROUBLESHOOTING BASED ON PROBLEM SYMPTOM

NEXT

11.CHECK CIRCUIT
11.CHECK CIRCUIT
a.

Adjust, repair or replace as necessary.


Result:
Proceed to
NEXT



NEXT

12.PERFORM CONFIRMATION TEST
12.PERFORM CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END