START DIAGNOSTIC MODE
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
Turn the ignition switch to ON.
Display the audio screen.
| *1 | Multi-display Assembly |
| *a | Upper Right Corner |
| *b | Upper Left Corner |
| *c | Audio Screen |
Touch the audio screen 5 times in the upper right corner, then 5 times in the upper left corner.
CHECK MODE SCREEN
Select "Failure Diagnosis" from the "Service Menu" screen.
Select "System Check" from the "Failure Diagnosis" screen.
CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)
System check mode screen description
| Display | Content |
|---|---|
| *a: Device name list |
·
Device Name List displays some of the devices that make up the Toyota multi operation touch system.
·
The names of the components from Device Name List are shown in the following table. |
| *b: Check result | Result codes for all devices are displayed. |
| *c: Memory clear |
·
Present and history DTCs and registered connected device names are cleared.
·
Select "Memory CLR" for 3 seconds. |
| *d: Recheck |
·
A system check will be performed again after the memory is cleared.
·
"Recheck" will dim during a system check. |
| Name | Component | Connection Method |
|---|---|---|
| TMOT | Integration control sub-assembly | - |
| DISP | Multi-display assembly | AVC-LAN communication line |
| Result | Meaning | Action |
|---|---|---|
| OK | The device does not respond with a DTC. | - |
| DETAIL | The device responds with a DTC. | Read the DTCs on the "Unit Check Mode" screen. |
| NCON | The device was previously present, but did not respond in diagnostic mode. |
·
Check the power supply circuit of the device.
·
Check the AVC-LAN communication line of the device. |
| NRES | The device responded in diagnostic mode, but gives no DTC information. |
·
Check the power supply circuit of the device.
·
Check the AVC-LAN communication line of the device. |
Unit check mode screen description
| Display | Content |
|---|---|
| *a: History DTC | Diagnostic memory results and stored DTCs are displayed. |
| *b: Present DTC | DTCs output in the service check are displayed. |
| *c: DTC | DTC (Diagnostic Trouble Code) |
| *d: Timestamp | The time and date of history DTCs are displayed. (The year is displayed in 2-digit format.) |
| *e: Diagnosis clear | Selecting "Code CLR" for 3 seconds clears the diagnostic memory data of the target device (both diagnostic system check result and the displayed data are cleared). |
This screen is updated once per second.
A maximum of 6 DTCs can be displayed for history and present DTCs.
Read the system check result.
If the check result is "DETAIL", select the displayed check result to view the results on the "Unit Check Mode" screen and record them.
A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit Check Mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit Check Mode" screen again to see if any other DTCs are displayed.
When all results are "OK", no DTCs are output.
When "NCON" is displayed for all devices connected via AVC-LAN communication, or when all device names are not displayed, check if there is a short in an AVC-LAN line or device connected to the AVC-LAN. Repair or replace parts as necessary.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>AVC-LAN Circuit
When proceeding to view the results of another device, select "Back" to return to the "System Check Mode" screen. Repeat the above step to view the results of other devices.
Check the details of the DTC(s).
DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)
Clear the DTCs
Select "Memory CLR" for 3 seconds.
Check that the check results are cleared.
To clear the DTCs for a specific device, use the "Unit Check Mode" screen.
When clearing the DTCs using the "Unit Check Mode" screen, select "Code CLR" for 3 seconds.
Recheck
Select "Recheck".
Check that all diagnostic codes are "OK" when the check results are displayed. If a result other than "OK" is displayed, perform troubleshooting again.
When the DTCs are cleared using the "Unit Check Mode" screen, select "Back" to return to the "System Check Mode" screen and perform this operation.
FINISH DIAGNOSTIC MODE
Turn the ignition switch off.