Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2021.04–2021.07
RM38G0E _56 Audio / Visual / Telematics _100607 NAVIGATION / MULTI INFO DISPLAY _0467503 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1579 Voice Recognition Microphone Disconnected Microphone signal is lost
·

Telephone microphone assembly

·

Radio receiver assembly

·

Harness or connector


Navigation System A

WIRING DIAGRAM

E379999E45
1.302,1.021 1.76,1.25 0.458,0.229 10 false SNS2 1.813,0.927 2.031,1.115 0.219,0.188 10 false 3 5.448,0.927 5.667,1.115 0.219,0.188 10 false 25 5.771,1.031 6.229,1.188 0.458,0.156 10 false SNS2 1.292,2.042 1.75,2.271 0.458,0.229 10 false MCO- 1.833,1.927 2.719,2.167 0.885,0.24 10 false 4 5.448,1.948 5.729,2.188 0.281,0.24 10 false 22 5.781,2.042 6.167,2.25 0.385,0.208 10 false MIN- 5.646,2.594 6.104,2.823 0.458,0.229 10 false I12 5.667,2.781 6.604,3.177 0.938,0.396 10 false Radio Receiver Assembly 0.333,2.563 1.271,2.813 0.938,0.25 10 false d28*1, d30*2 0.302,2.75 2.594,3.188 2.292,0.438 10 false Telephone Microphone Assembly 0.188,3.104 1.01,3.302 0.823,0.198 10 false *1: for LHD 0.198,3.385 1.021,3.583 0.823,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)

Pre-procedure1

a.

Disconnect the I12 radio receiver assembly connector.


b.

Disconnect the d28*1 or d30*2 telephone microphone assembly connector.

*1: for LHD

*2: for RHD



Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(I12,d28)Location & Routing

Click Connector(I12)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(d28)Body>No. 1 Roof Wire>Telephone Microphone Assembly LH

I12-25 (SNS2) - d28-3 (SNS2) Always Below 1 Ω
I12-22 (MIN-) - d28-4 (MCO-) Always Below 1 Ω
I12-25 (SNS2) - Body ground Always 10 kΩ or higher
I12-22 (MIN-) - Body ground Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(I12,d30)Location & Routing

Click Connector(I12)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(d30)Body>No. 1 Roof Wire>Telephone Microphone Assembly RH

I12-25 (SNS2) - d30-3 (SNS2) Always Below 1 Ω
I12-22 (MIN-) - d30-4 (MCO-) Always Below 1 Ω
I12-25 (SNS2) - Body ground Always 10 kΩ or higher
I12-22 (MIN-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

2.INSPECT TELEPHONE MICROPHONE ASSEMBLY (SNS2, MCO-)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT TELEPHONE MICROPHONE ASSEMBLY (SNS2, MCO-)

Pre-procedure1

a.

Remove the telephone microphone assembly.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL



Procedure1

b.
E364293C26
1.76,1.229 2.01,0.458 2.01,0.458 2.198,0.458 true 1.458,1.229 1.188,0.469 1.188,0.469 0.958,0.469 true 2.26,0.385 2.698,0.552 0.438,0.167 10 false SNS2 0.5,0.375 1.25,0.646 0.75,0.271 10 false MCO- 0.125,0.094 0.563,0.26 0.438,0.167 10 false *a
*A for LHD
*B for RHD
*a Component without harness connected
(Telephone Microphone Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SNS2) - 4 (MCO-) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

NG

REPLACE TELEPHONE MICROPHONE ASSEMBLY