Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for V35A-FTS)
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467935 COMPRESSOR(for V35A-FTS) A

HEATING / AIR CONDITIONING  COMPRESSOR(for V35A-FTS)  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
E460163N03
0.573,0.896 5.146,3.375 4.573,2.479 0.625,3.625 1.333,3.833 0.708,0.208 2.823,3.375 2.823,3.74 false 5.813,2.521 6.208,2.521 false 1.667,1.479 1.313,1.479 1.313,1.479 1.094,2 true 3.833,2.958 3.479,2.958 3.479,2.958 3.25,2.677 true 4.75,2.563 4.531,2.563 4.531,2.563 4.396,2.281 true 3.844,2.958 3.49,2.958 3.49,2.958 3.26,2.677 true 2.354,2.167 2.229,1.865 2.229,1.865 1.938,1.865 true 3.667,1.854 3.542,1.396 3.542,1.396 3.313,1.396 true 1.698,2.552 1.698,3.042 1.698,3.042 2.448,3.042 false 1.875,2.5 1.875,3.042 false 2.063,2.458 2.063,3.031 false 6.323,0.271 6.719,0.271 false 0.302,2.813 0.302,3.719 0.302,3.719 0.615,3.719 false 3.208,1.302 3.365,1.5 0.156,0.198 10 false ● 6.281,2.375 6.563,2.729 0.281,0.354 18 false 3 2.875,3.719 3.156,4.073 0.281,0.354 18 false 1 1.823,1.781 1.979,1.979 0.156,0.198 10 false ● 1.771,1.396 2.083,1.594 0.313,0.198 10 false *1 3.927,2.865 4.24,3.063 0.313,0.198 10 false *3 4.792,2.479 5.104,2.677 0.313,0.198 10 false *4 2.51,2.969 2.823,3.167 0.313,0.198 10 false *2 6.156,0.115 6.438,0.469 0.281,0.354 18 false 2 0.667,3.656 2.135,3.813 1.469,0.156 8 false 18 (184, 13)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 MAGNET CLUTCH ASSEMBLY 88410 (Click here) - -
2 MAGNET CLUTCH CLEARANCE - (Click here) - -
3 NO. 2 COOLER COMPRESSOR BRACKET 88849 - - -

*1 MAGNET CLUTCH HUB *2 MAGNET CLUTCH WASHER
*3 MAGNET CLUTCH ROTOR *4 MAGNET CLUTCH STATOR
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

PROCEDURE

Hide 88410 1.INSTALL MAGNET CLUTCH ASSEMBLY

a.
E460167C01
0.667,3.104 0.823,2.854 0.823,2.854 1.042,2.854 true 4.708,1.406 4.99,1.406 4.99,1.406 5.125,1.563 true 4.917,4.427 5.115,4.688 5.115,4.688 5.313,4.688 true 0.521,0.115 0.802,0.469 0.281,0.354 18 false i 1.094,2.76 1.406,2.958 0.313,0.198 10 false *a 4.542,0.583 4.854,0.781 0.313,0.198 10 false *b 4.333,3.344 4.646,3.542 0.313,0.198 10 false *b 4.177,0.583 4.49,0.781 0.313,0.198 10 false *c 3.979,3.354 4.292,3.552 0.313,0.198 10 false *c 4.635,3.365 4.948,3.563 0.313,0.198 10 false *d 4.854,0.604 5.167,0.802 0.313,0.198 10 false *d 5.354,4.594 5.667,4.792 0.313,0.198 10 false *a 4.531,1.323 4.844,1.521 0.313,0.198 10 false *a
*a SST *b Chamfered Side
*c Inside *d Outside


i.

Install the magnet clutch assembly using the following procedure.

1. Clamp the cooler compressor assembly in a vise between aluminum plates.

2. Install the magnet clutch stator with the parts aligned as shown in the illustration.

3. Using SST, install a new snap ring with the chamfered side facing outward.

SST
09904-00011  

NOTICE:

When installing the snap ring, do not widen it excessively.


4. Using SST, install the magnet clutch rotor and a new snap ring with the chamfered side facing outward.

SST
09904-00011  

NOTICE:
·

Do not damage the seal cover of the bearing when installing the snap ring.

·

When installing the snap ring, do not widen it excessively.



5. Install the magnet clutch washer(s) and magnet clutch hub.

NOTICE:

Do not change the combination of the magnet clutch washer(s) used before disassembly.


6. Using SST, hold the magnet clutch hub and install the bolt.

SST
09985-00270  

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Make sure that there is no foreign matter or oil on the compressor shaft, bolt and magnet clutch hub.




Hide 2.INSPECT MAGNET CLUTCH CLEARANCE

a.
E460169N01
2.698,0.427 2.927,0.427 true 2.104,0.156 2.385,0.51 0.281,0.354 18 false i 2.958,0.354 3.417,0.552 0.458,0.198 10 false MG+

i.

Inspect the magnet clutch clearance using the following procedure.

1. Set a dial indicator to the magnet clutch hub.

2. Connect a battery positive lead to terminal 1 of the magnet clutch connector and a negative lead to the ground wire. Turn the magnet clutch on and off and measure the clearance.

Standard Clearance:

0.35 to 0.60 mm (0.0138 to 0.0236 in.)


NOTICE:

Adjustment should be performed with 3 or fewer magnet clutch washers.


HINT:

If the measured value is not within the standard clearance, remove the magnet clutch hub and adjust the clearance using magnet clutch washers to obtain the standard clearance.


3. Remove the compressor with magnet clutch from the vise.



Hide 88849 3.INSTALL NO. 2 COOLER COMPRESSOR BRACKET