A backup boost converter is built into the engine stop and start ECU.
The backup boost converter helps maintain battery voltage to prevent various functions from failing if power source voltage supplied from the backup boost converter drops due to the high electrical load when the engine is restarted by stop and start control.
The backup boost converter helps maintain the power source voltage if the battery voltage drops due to the high electrical load when the engine is restarted by stop and start control.
A relay function and fuse function are provided in the backup boost converter.
If there is a malfunction in any of the electrical system circuits connected to the backup boost converter, the fuse and relay functions shut off the malfunctioning circuit to protect other circuits (remains shut off until next trip).
When the electrical system circuit is shut off, power to the circuit is cut off, causing any systems connected to the circuit to be disabled.
The fuse function is reset* when the ignition switch is turned off. If the malfunction still exists in the electrical system circuit that has been shut off by the relay function, it will be shut off again by the relay and fuse functions the next time the ignition switch is turned to ON.
*: A semiconductor fuse self resets according to electric signal.
Tire pressure warning system
Toyota multi operation touch system
Headup display system
Pre-Collision System
Air conditioning system
Parking support brake system
Vehicle stability control system
Navigation system
Lighting system
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Note |
|---|---|---|---|---|---|
| P323A19 | Backup Boost Converter "A" Circuit Current Above Threshold | The following condition continues for 1 second or more (2 trip detection logic):
·
Overcurrent is detected at the B41, B42, B43 and IG41 terminals in the engine stop and start ECU |
·
Engine stop and start ECU
·
Wire harness or connector
·
Tire pressure warning ECU and receiver
·
Integration control sub-assembly
·
Meter mirror sub-assembly
·
Millimeter wave radar sensor assembly
·
No. 2 air conditioning control assembly
·
Clearance warning ECU assembly
·
Air conditioning control assembly
·
No. 1 skid control ECU (brake booster with master cylinder assembly)
·
Radio receiver assembly
·
Multi-display
·
Integration control sub-assembly
·
Navigation ECU
·
No. 1 interior illumination light assembly (for driver side)
·
No. 1 interior illumination light assembly (for front passenger side)
·
No. 1 interior illumination light assembly LH
·
No. 1 interior illumination light assembly RH
·
Rear door inside handle illumination light assembly LH
·
Rear door inside handle illumination light assembly RH
·
Front door inside handle illumination light assembly LH
·
Front door inside handle illumination light assembly RH
·
Vanity light assembly (for LH side)
·
Vanity light assembly (for RH side) |
Blinks | SAE Code: P323A |
CONFIRMATION AFTER TROUBLESHOOTING
If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.
In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)
If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.
If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.
After the refresh charge completes, turnthe ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.
Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.
Clear the DTCs.
Start the engine and warm it up.
Drive the vehicle at 7 km/h (4.3 mph) or more.
When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.
Depress the brake pedal and stop the vehicle.
Keep the engine stopped by stop and start control for 1 second or more. (Keep the shift lever in D.)
Release the brake pedal with the shift lever in D to start the engine.
If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.
Check that DTCs are not output.
STOP AND START SYSTEM OPERATION CHECK
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>OPERATION CHECK
Before replacing the engine stop and start ECU, read the number of starter operations, total number of engine starts and write it into a new engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
If electrical load from additional devices installed to the vehicle (aftermarket audio system, etc.) is applied to the B41, B42, B43 or IG41 terminal in the engine stop and start ECU, the fuse function of the backup boost converter may operate.
If the fuse function of the backup boost converter operates, any systems connected to the B41, B42, B43 or IG41 terminal in the engine stop and start ECU will not operate.
DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.
Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA
Disconnect the engine stop and start ECU connector.
Remove the BBC NO. 1 and BBC NO. 2 fuses from the NO. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B37)Location & Routingewd_type=routing;type=c;code=B37 Click Connector(B37)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B37;pinno=1,3 |
||
| B37-1 (BIN2) - BBC NO. 2 fuse terminal 2 | Always | Below 1 Ω |
| B37-3 (BIN1) - BBC NO. 1 fuse terminal 2 | Always | Below 1 Ω |
| B37-1 (BIN2) - Body ground | Always | 10 kΩ or higher |
| BBC NO. 2 fuse terminal 2 - Body ground | Always | 10 kΩ or higher |
| B37-3 (BIN1) - Body ground | Always | 10 kΩ or higher |
| BBC NO. 1 fuse terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine stop and start ECU connector.
Disconnect the tire pressure warning ECU and receiver connector.
Disconnect the integration control sub-assembly connector.
Disconnect the meter mirror sub-assembly connector.
Disconnect the No. 2 air conditioning control assembly connector.
Disconnect the clearance warning ECU assembly connector.
Disconnect the air conditioning control assembly connector.
Disconnect the millimeter wave rader sensor assembly connector.
Disconnect the No. 1 skid control ECU (brake booster with master cylinder assembly) connector.
Disconnect the radio receiver assembly connector.
Disconnect the multi-display connector.
Disconnect the navigation ECU connector.
Disconnect the No. 1 interior illumination light assembly (for driver side) connector.
Disconnect the No. 1 interior illumination light assembly (for front passenger side) connector.
Disconnect the No. 1 interior illumination light assembly LH connector.
Disconnect the No. 1 interior illumination light assembly RH connector.
Disconnect the rear door inside handle illumination light switch LH connector.
Disconnect the rear door inside handle illumination light switch RH connector.
Disconnect the front door inside handle illumination light switch LH connector.
Disconnect the front door inside handle illumination light switch RH connector.
Disconnect the vanity light assembly LH connector.
Disconnect the vanity light assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: for 12.3 Inch Display *2: w/ Headup Display System *3: w/ Pre-collision System *4: w/ Rear Heater *5: except 14 speaker *6: for 14 speaker *7: for Bulb type *8: for LED type |
||
Click Location & Routing(I57,T11,I22,I17,A10,Q52,I58,I78,B19,I8,I10,I18,I21,I61,I62,i6,h11,P5,O5,N8,M10,d5,d9,d4,d8)Location & Routingewd_type=routing;type=c,c,c,c,c,c,c,c,c,c,c,c,c,c,c,c,c,c,c,c,c,c,c,c,c;code=I57,T11,I22,I17,A10,Q52,I58,I78,B19,I8,I10,I18,I21,I61,I62,i6,h11,P5,O5,N8,M10,d5,d9,d4,d8 Click Connector(T11)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Electrical Key & Tire Pressure Monitoring System Receiver Assemblyewd_type=component;type=c;code=T11;pinno=1,7 Click Connector(A10)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Millimeter Wave Radar Sensor Assemblyewd_type=component;type=c;code=A10;pinno=8 Click Connector(Q52)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooler Control Switch Assemblyewd_type=component;type=c;code=Q52;pinno=10 Click Connector(i6)Seat>Front Seat Wire LH>Foot Light LH (No. 1 Interior Illumination Light Assembly LH)ewd_type=component;type=c;code=i6;pinno=2 Click Connector(h11)Seat>Front Seat Wire RH>Foot Light RH (No. 1 Interior Illumination Light Assembly RH)ewd_type=component;type=c;code=h11;pinno=2 Click Connector(P5)Body>No. 2 Rear Door Wire>Rear Door Inside Handle Illumination Light Assembly LHewd_type=component;type=c;code=P5;pinno=1 Click Connector(O5)Body>No. 1 Rear Door Wire>Rear Door Inside Handle Illumination Light Assembly RHewd_type=component;type=c;code=O5;pinno=1 Click Connector(N8)Body>Front Door Wire LH>Front Door Inside Handle Illumination Light Assembly LHewd_type=component;type=c;code=N8;pinno=1 Click Connector(M10)Body>Front Door Wire RH>Front Door Inside Handle Illumination Light Assembly RHewd_type=component;type=c;code=M10;pinno=1 Click Connector(d5)Body>No. 1 Roof Wire>Vanity Light Assembly LHewd_type=component;type=c;code=d5;pinno=1 Click Connector(d9)Body>No. 1 Roof Wire>Vanity Light Assembly LHewd_type=component;type=c;code=d9;pinno=2 Click Connector(d4)Body>No. 1 Roof Wire>Vanity Light Assembly RHewd_type=component;type=c;code=d4;pinno=1 Click Connector(d8)Body>No. 1 Roof Wire>Vanity Light Assembly RHewd_type=component;type=c;code=d8;pinno=2 |
||
| I57-3 (IG41) - T11-1 (IG) | Always | Below 1 Ω |
| I57-3 (IG41) - I22-4 (IG+)*1 | Always | Below 1 Ω |
| I57-3 (IG41) - I17-1 (IG)*2 | Always | Below 1 Ω |
| I57-3 (IG41) - A10-8 (IGB)*3 | Always | Below 1 Ω |
| I57-3 (IG41) - Q52-10 (IG)*4 | Always | Below 1 Ω |
| I57-3 (IG41) - I58-1 (IG) | Always | Below 1 Ω |
| I57-3 (IG41) - I78-8 (IG+) | Always | Below 1 Ω |
| I57-2 (B41) - T11-7 (+B) | Always | Below 1 Ω |
| I57-2 (B41) - B19-14 (+BI1) | Always | Below 1 Ω |
| I57-12 (B42) - I8-4 (+B1)*5 | Always | Below 1 Ω |
| I57-12 (B42) - I10-4 (+B1)*6 | Always | Below 1 Ω |
| I57-11 (B43) - I18-12 (B)*1 | Always | Below 1 Ω |
| I57-11 (B43) - I21-10 (+B) | Always | Below 1 Ω |
| I57-11 (B43) - I17-2 (B)*2 | Always | Below 1 Ω |
| I57-11 (B43) - I78-16 (+B) | Always | Below 1 Ω |
| I57-11 (B43) - I22-1 (B)*1 | Always | Below 1 Ω |
| I57-11 (B43) - I61-2 (B) | Always | Below 1 Ω |
| I57-11 (B43) - I62-2 (B) | Always | Below 1 Ω |
| I57-11 (B43) - i6-2 | Always | Below 1 Ω |
| I57-11 (B43) - h11-2 | Always | Below 1 Ω |
| I57-11 (B43) - P5-1 (+) | Always | Below 1 Ω |
| I57-11 (B43) - O5-1 (+) | Always | Below 1 Ω |
| I57-11 (B43) - N8-1 (+) | Always | Below 1 Ω |
| I57-11 (B43) - M10-1 (+) | Always | Below 1 Ω |
| I57-11 (B43) - d5-1 (B)*7 | Always | Below 1 Ω |
| I57-11 (B43) - d9-2 (B)*8 | Always | Below 1 Ω |
| I57-11 (B43) - d4-1 (B)*7 | Always | Below 1 Ω |
| I57-11 (B43) - d8-2 (B)*8 | Always | Below 1 Ω |
| I57-3 (IG41) - Body ground | Always | 10 kΩ or higher |
| I57-2 (B41) - Body ground | Always | 10 kΩ or higher |
| I57-12 (B42) - Body ground | Always | 10 kΩ or higher |
| I57-11 (B43) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine stop and start ECU connectors.
| *a | Component without harness connected (Engine Stop and Start ECU) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,B38)Location & Routingewd_type=routing;type=c,c;code=I57,B38 Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B38;pinno=6 |
||
| I57-3 (IG41) - B38-6 (DGND) | Always | 10 kΩ or higher |
| I57-2 (B41) - B38-6 (DGND) | Always | 10 kΩ or higher |
| I57-12 (B42) - B38-6 (DGND) | Always | 10 kΩ or higher |
| I57-11 (B43) - B38-6 (DGND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that additional devices installed to the vehicle (aftermarket audio system, etc.) are not connected to the B41, B42, B43 or IG41 terminal circuit of the engine stop and start ECU.
| Result | Proceed to |
|---|---|
| Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is not applied. | A |
| Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is applied. | B |
A
B