Before performing troubleshooting for the front camera system, perform troubleshooting for the pre-collision system.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>PRE-COLLISION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If a pre-collision system related warning message is displayed on the multi-information display, refer to How to Proceed with Troubleshooting for the pre-collision system.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>PRE-COLLISION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Use the following procedure to troubleshoot the front camera system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Interview the customer and confirm the problem.
| Proceed to |
|---|
| NEXT |
NEXT
Measure the battery voltage.
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
Check the fuses and relays.
Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, check for CAN communication system DTCs.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN DTCs are not output | A |
| CAN DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Using the GTS, check for DTCs.
If a DTC is output, record the DTC.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC C1AA800 is output | B |
| DTC other than C1AA800 is output | C |
A
B
C
Using the GTS, clear the DTCs.
Reproduce the vehicle conditions that were present when the DTCs that were noted were stored.
Refer to each corresponding DTC for details on the detection conditions.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Using the GTS, check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Using the GTS, check for Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Make a note of the output Vehicle Control History (RoB).
| Result | Proceed to |
|---|---|
| Vehicle Control History (RoB) is not output | A |
| Vehicle Control History (RoB) other than X2015 and X201C is output | B |
| Vehicle Control History (RoB) X2015 or X201C is output | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA SYSTEM>VEHICLE CONTROL HISTORY (RoB)
Using the GTS, clear the Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Using the GTS, check for Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| Vehicle Control History (RoB) is not output | A |
| Vehicle Control History (RoB) is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA SYSTEM>VEHICLE CONTROL HISTORY (RoB)