Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › PRE-COLLISION SYSTEM
RM38G0E _95 ADAS / AD _100650 ADVANCED DRIVER ASSISTANCE SYSTEM _0469137 PRE-COLLISION SYSTEM Y

ADVANCED DRIVER ASSISTANCE SYSTEM  PRE-COLLISION SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use these procedures to troubleshoot the pre-collision system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CHECK
2.CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CHECK
a.

Interview the customer and confirm the problem.


Result:
Proceed to
NEXT



NEXT

3.PRE-CHECK
3.PRE-CHECK
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


HINT:

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.



b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK MULTI-INFORMATION DISPLAY
4.CHECK MULTI-INFORMATION DISPLAY
a.

Check if a pre-collision system warning message is displayed on the multi-information display in the combination meter assembly.

HINT:

If more than one warning message is displayed, check in the order of A, B, C, D and E.



Result:
Result Proceed to
"VSC Turned OFF Pre-Collision Brake System Unavailable" is displayed A
"Pre-Collision System Malfunction Visit Your Dealer" is displayed B
"Pre-Collision System Radar Sensor Blocked Unavailable Clean Radar Sensor" is displayed C
Any of the following messages is displayed:
·

"Pre-Collision System Unavailable See Owner's Manual"

·

"Pre-Collision System Out of Temperature Range Unavailable See Owner's Manual"

·

"Pre-Collision System Radar In Self Calibration Unavailable See Owner's Manual"

·

"Front Camera Out of Temperature Range Unavailable Wait until Normal Temperature"

·

"Front Camera Low Visibility Unavailable See Owner's Manual"

·

"Front Camera Unavailable See Owner's Manual"


D
Pre-collision system warning message is not displayed E



A

B

5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

C

10.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY

D

7.CHECK VEHICLE CONTROL HISTORY (RoB)*

E

14.PROBLEM SYMPTOMS TABLE
5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check for CAN communication system DTCs.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN DTCs are not output A
CAN DTCs are output B



A

6.CHECK FOR DTCs*

B

6.CHECK FOR DTCs*
a.

Check for DTCs.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432

Result:
Result Proceed to
DTCs are not output A
DTC (C142571) is output B
A DTC other than (C142571) is output C



A

7.CHECK VEHICLE CONTROL HISTORY (RoB)*

B

C

9.CHECK FOR DTCs*
7.CHECK VEHICLE CONTROL HISTORY (RoB)*
a.

Using the GTS, check for Vehicle Control History (RoB).

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55

b.

If the Vehicle Control History (RoB) is output, record it.


Result:
Result Proceed to
Vehicle control history (RoB) is not output A
Vehicle control history (RoB) (X2013, X2015, X2022, X2025, X2026 or X2028) is output B
Vehicle control history (RoB) other than (X2013, X2015, X2022, X2025, X2026 and X2028) is output C



A

B

C

8.RECHECK VEHICLE CONTROL HISTORY (RoB)*
8.RECHECK VEHICLE CONTROL HISTORY (RoB)*
a.

Using the GTS, clear the Vehicle Control History (RoB).

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55

b.

Using the GTS, check for Vehicle Control History (RoB).

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55

Result:
Result Proceed to
Vehicle Control History (RoB) is not output A
Vehicle Control History (RoB) is output B



A

B

9.CHECK FOR DTCs*
a.

Using the GTS, clear the DTCs.

Body Electrical > Pre-Collision System > Clear DTCs
50002 432

b.

Reproduce the vehicle conditions that were present when the DTCs that were noted were stored.

HINT:

Refer to each corresponding DTC for details on the detection conditions.



c.

Using the GTS, check if the DTCs are output again.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

B

10.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Check whether the millimeter wave radar sensor assembly and surrounding area is dirty or obstructed by foreign matter.


HINT:

Check that the following situations do not occur.

·

A cover other than the dedicated radar sensor cover is not installed

·

There is no dirt on the radar sensor cover or millimeter wave radar sensor assembly

·

An accessory, such as bull bars, a grille guard, etc., which interferes with millimeter radio waves is installed

·

There is no sticker or coating applied to the dedicated radar sensor cover

·

There is no foreign matter between the radar sensor cover and millimeter wave radar sensor assembly



b.

Clean away any dirt or foreign matter that is adhering to the area around the millimeter wave radar sensor assembly.


Result:
Proceed to
NEXT



NEXT

11.CHECK MULTI-INFORMATION DISPLAY
11.CHECK MULTI-INFORMATION DISPLAY
NOTICE:

Before inspecting the multi-information display, be sure to first turn the ignition switch off and then to ON again.


a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON.


c.

Check whether "Pre-Collision System Radar Sensor Blocked Unavailable Clean Radar Sensor" is displayed on the multi-information display.


Result:
Result Proceed to
Not displayed A
Displayed B



A

12.READ VALUE USING GTS (ON-LINE CALIBRATION ANGLE (HORIZONTAL))

B

ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.

Triangle Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

Flat Surface Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT



12.READ VALUE USING GTS (ON-LINE CALIBRATION ANGLE (HORIZONTAL))
a.

Using the GTS, read the following Data List item for the front radar sensor system.

Body Electrical > Front Radar Sensor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
On-Line Calibration Angle (Horizontal) Calibrated angle value (horizontal) -12.8 to 12.7 deg Learned value -
Body Electrical > Front Radar Sensor > Data List
Tester Display
On-Line Calibration Angle (Horizontal)
50003 429 40

Standard:

The value displayed is less than -0.5 to 0.5 deg.


Result:
Proceed to
OK
NG



OK

13.EXPLAIN TO CUSTOMER

NG

ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.

Triangle Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

Flat Surface Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT



13.EXPLAIN TO CUSTOMER
a.

Explain to the customer that the "Pre-Collision System Radar Sensor Blocked Unavailable Clean Radar Sensor" message on the multi-information display was caused by dirt or foreign matter adhering to the area around the millimeter wave radar sensor assembly, and that the situation has been corrected.


Result:
Proceed to
NEXT



NEXT

END

14.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

15.CHECK PCS WARNING LIGHT

B

15.CHECK PCS WARNING LIGHT
a.

Check the condition of the PCS warning light.


Result:
Result Proceed to
Only the PCS warning light is illuminated A
The PCS warning light is not illuminated B



A

16.CHECK VEHICLE CONTROL HISTORY (RoB)* (X2015)

B

17.CHECK FOR DTCs*
16.CHECK VEHICLE CONTROL HISTORY (RoB)* (X2015)
a.

Check for vehicle control history (RoB) and note any codes that are output.

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55

Result:
Proceed to
NEXT



NEXT

17.CHECK FOR DTCs*
a.

Check for DTCs.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

18.CHECK CONFIRMED DTC DETECTION CONDITION*

B

19.CHECK VEHICLE CONTROL HISTORY (RoB)*
18.CHECK CONFIRMED DTC DETECTION CONDITION*
a.

Check detection condition for the confirmed pre-collision system DTC.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>PRE-COLLISION SYSTEM>FAIL-SAFE CHART


Result:
Proceed to
NEXT



NEXT

END

Explain to the customer the cause of the previously stored DTC and that the output reason has been cleared.


19.CHECK VEHICLE CONTROL HISTORY (RoB)*
a.

Check for vehicle control history (RoB) and note any codes that are output.

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55
i.

Record the vehicle control history (RoB).



Result:
Result Proceed to
Vehicle control history (RoB) is not output A
Vehicle control history (RoB) is output B



A

20.CONDITIONS WHEN PRE-COLLISION SYSTEM OPERATE OR NOT OPERATE

B

22.CHECK VEHICLE CONTROL HISTORY (RoB)* (PRE-COLLISION SYSTEM)
20.CONDITIONS WHEN PRE-COLLISION SYSTEM OPERATE OR NOT OPERATE
a.

Check the conditions when pre-collision system operates or does not operate.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>PRE-COLLISION SYSTEM>PRECAUTION


Result:
Result Proceed to
No condition is met A
Any condition is met B



A

21.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY* (FRONT BEAM AXIS MISALIGNMENT READING)

B

END (OPERATION/NO OPERATION CONDITIONS OF PRE-COLLISION SYSTEM IS MET)

21.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY* (FRONT BEAM AXIS MISALIGNMENT READING)
NOTICE:

Before performing beam axis adjustment, check the fitting of the front bumper cover and radiator grille assembly and confirm that there is no warping or deformation.




c.

Turn the cruise control main switch on.


d.

Check the amount of misalignment and make a note.

Body Electrical > Front Radar Sensor > Utility
Tester Display
Front Beam Axis Misalignment Reading
50005 429 4405
Standard (before performing adjustment):
Front beam axis misalignment value:
Vertical -5.0 to 5.0 deg.
Horizontal -0.6 to 0.6 deg.



Result:
Result Proceed to
Front beam axis misalignment value is within the specified range A
Front beam axis misalignment value is not within the specified range B



A

B

PERFORM FRONT BEAM AXIS ADJUSTMENT
HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.

Triangle Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

Flat Surface Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT



22.CHECK VEHICLE CONTROL HISTORY (RoB)* (PRE-COLLISION SYSTEM)
a.

Check for vehicle control history (RoB) and note any codes that are output.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY (RoB)

HINT:

Based on the customer's inquiry, check the corresponding factors in the vehicle control history (RoB), such as the detection time and date, trip information and elapsed time.



Result:
Proceed to
NEXT



NEXT

END
a.

Explain to the customer the cause of the previously stored vehicle control history (RoB) and that the output reason has been cleared.

NOTICE:

After the explanation, make sure to clear vehicle control history (RoB).


Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 1055