Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P161311  AIR System Driver Circuit Short to Ground  P161315  AIR System Driver Circuit Short to Battery or Open  P161364  AIR System Driver Signal Plausibility Failure  


DESCRIPTION

Refer to DTC P041211

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P041211

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P161311 AIR System Driver Circuit Short to Ground

All of following conditions met (1 trip detection logic):

(a)

Secondary air injection system operating (air switching valve ON and air pump ON)

(b)

Diagnostic signal from air injection control driver 0%

(c)

Battery voltage 8 V or more



·

Short in diagnostic information signal circuit (air injection control driver - ECM)

·

Open or short in air pump and air switching valve command signal circuit (air injection control driver - ECM)

·

Open in air injection control driver ground circuit

·

Air injection control driver

·

ECM


Comes on SAE: P1613
P161315 AIR System Driver Circuit Short to Battery or Open

Both of following conditions met (1 trip detection logic):

(a)

Battery voltage 8 V or more

(b)

Diagnostic signal from air injection control driver 100%



·

Open or short in air injection control driver power source circuit

·

Open in diagnostic information signal circuit (air injection control driver - ECM)

·

Air injection control driver

·

ECM


Comes on SAE: P1613
P161364 AIR System Driver Signal Plausibility Failure Either of following conditions (1) or (2) met
(1) All of following conditions met (1 trip detection logic):
·

Either of air pump or air switching valve not operating

·

Diagnostic signal from air injection control driver 80%

·

Battery voltage 8 V or more


(2) Both of following conditions met (1 trip detection logic):
·

Battery voltage 8 V or more

·

Diagnostic signal from air injection control driver abnormal (duty signal other than 0, 20, 40, 80 and 100%)


·

Air injection control driver

·

Open in air injection control driver ground circuit


Comes on SAE: P1613

MONITOR DESCRIPTION

This DTC indicates an open or short circuit in the circuit containing the air pump of the secondary air injection system. The air injection control driver performs diagnosis of the air pump assembly, emission control valve set and itself, and sends the results of this diagnosis to the ECM as a duty signal. When the ECM receives a signal indicating a malfunction in the air pump assembly, emission control valve set or air injection control driver assembly, it immediately illuminates the MIL and stores a DTC.

CONFIRMATION DRIVING PATTERN

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the GTS on.

6.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the GTS on.

9.

Enter the following menus: Powertrain / Engine / Utility / Secondary Air Injection Check / Automatic Mode.

10.

Start the engine after the GTS initialization is finished.

11.

Perform the System Check operation by pressing Next.

12.

Perform the following to confirm the secondary air injection system pending DTCs: Press Exit.

13.

Enter the following menus: Powertrain / Engine / DTC.

14.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



15.

After Secondary Air Injection Check is completed, check All Readiness by entering the following menus: Powertrain / Engine / Utility / All Readiness.

16.

Input the DTC: P161377, P161315 or P161364.

17.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

By using the GTS to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO SECONDARY AIR INJECTION SYSTEM DTCS)
a.

Turn the ignition switch to ON.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P161311, P161315 and/or P161364 are output A
DTC P161311, P161315 and/or P161364 and other DTCs are output B


HINT:

If any DTCs other than P161311, P161315 and/or P161364 are output, troubleshoot those DTCs first.




A

2.CHECK AIR INJECTION CONTROL DRIVER ASSEMBLY (POWER SOURCE CIRCUIT)

B

2.CHECK AIR INJECTION CONTROL DRIVER ASSEMBLY (POWER SOURCE CIRCUIT)
a.

Disconnect the air injection control driver assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C96)Location & Routing

Click Connector(C96)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Injection Control Driver

C96-5 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER ASSEMBLY - ECM, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER ASSEMBLY - ECM, BODY GROUND)
a.

Disconnect the ECM connector.


b.

Disconnect the air injection control driver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C92,C96)Location & Routing

Click Connector(C92)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C96)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Injection Control Driver

C92-63 (AIRP) - C96-4 (SIP) Always Below 1 Ω
C92-61 (AIRV) - C96-3 (SIV) Always Below 1 Ω
C92-52 (AIDI) - C96-2 (DI) Always Below 1 Ω
C96-1 (E) - Body ground Always Below 1 Ω
C92-63 (AIRP) or C96-4 (SIP) - Body ground Always 10 kΩ or higher
C92-61 (AIRV) or C96-3 (SIV) - Body ground Always 10 kΩ or higher
C92-52 (AIDI) or C96-2 (DI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT AIR INJECTION CONTROL DRIVER ASSEMBLY (DI TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT AIR INJECTION CONTROL DRIVER ASSEMBLY (DI TERMINAL VOLTAGE)
a.

Disconnect the air injection control driver assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C96)Location & Routing

Click Connector(C96)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Injection Control Driver

C96-2 (DI) - C96-1 (E) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.PERFORM ACTIVE TEST USING GTS

NG

5.PERFORM ACTIVE TEST USING GTS
a.
A488681C01
0.635,0.417 0.948,0.615 0.313,0.198 10 false *1 2.552,0.365 2.865,0.563 0.313,0.198 10 false *2 0.823,0.885 1.135,1.083 0.313,0.198 10 false DI 0.771,1.24 1.083,1.438 0.313,0.198 10 false SIV 2.438,0.865 2.75,1.063 0.313,0.198 10 false AIDI 2.438,1.229 2.854,1.427 0.417,0.198 10 false AIRV
*1 Air Injection Control Driver
*2 ECM


Disconnect the air injection control driver assembly connector.


b.

Connect terminals DI and SIV of the wire harness connector for the air injection control driver assembly.


c.

Start the engine.


d.

Perform the secondary air injection system forced operation while the engine is idling.

Powertrain > Engine > Utility
Tester Display
Secondary Air Injection Check
50005 372 26
HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



e.

Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is ON and OFF.


f.

Turn the ignition switch off.

NOTICE:
·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(C96)Location & Routing

Click Connector(C96)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Injection Control Driver

C96-3 (SIV) - C96-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
C96-3 (SIV) - C96-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



g.
A488681C02
0.813,0.875 1.125,1.073 0.313,0.198 10 false DI 0.656,0.438 0.969,0.635 0.313,0.198 10 false *1 2.542,0.344 2.854,0.542 0.313,0.198 10 false *2 2.406,0.854 2.719,1.052 0.313,0.198 10 false AIDI 0.76,1.219 1.073,1.417 0.313,0.198 10 false SIP 2.406,1.229 2.813,1.427 0.406,0.198 10 false AIRP
*1 Air Injection Control Driver Assembly
*2 ECM


Connect terminals DI and SIP of the wire harness connector for the air injection control driver assembly.


h.

Start the engine.


i.

Perform the secondary air injection system forced operation while the engine is idling.

Powertrain > Engine > Utility
Tester Display
Secondary Air Injection Check
50005 372 26
HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



j.

Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is ON and OFF.


k.

Turn the ignition switch off.

NOTICE:
·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(C96)Location & Routing

Click Connector(C96)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Injection Control Driver

C96-4 (SIP) - C96-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
C96-4 (SIP) - C96-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



l.

Reconnect the air injection control driver assembly connector.


Result:
Proceed to
OK
NG



OK

6.REPLACE AIR INJECTION CONTROL DRIVER ASSEMBLY

NG

6.REPLACE AIR INJECTION CONTROL DRIVER ASSEMBLY
a.

Replace the air injection control driver assembly.

Click hereEngine / Hybrid System>1GR-FE (EMISSION CONTROL)>AIR INJECTION DRIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Clear the DTCs

Powertrain > Engine > Clear DTCs
50002 372

e.

Perform the System Check operation (Automatic Mode).

Powertrain > Engine > Utility
Tester Display
Secondary Air Injection Check
50005 372 26

f.

Start the engine after the GTS initialization is finished.


g.

After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending codes: Press the Exit button.


h.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
No DTC is output A
Other DTCs are output B



i.

Turn the ignition switch off.

NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.





A

END

B