Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM U

1GR-FE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


C458640N01
2.229,0.281 2.615,0.542 0.385,0.26 5.427,0.281 5.813,0.542 0.385,0.26 2.302,0.333 2.615,0.542 0.313,0.208 10 false C92 5.542,0.333 5.854,0.542 0.313,0.208 10 false B2

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
B2-1 (BATT) - C92-81 (E1) Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
B2-2 (+B) - C92-81 (E1) Power source of ECM Ignition switch ON 11 to 14 V
B2-3 (+B2) - C92-81 (E1) Power source of ECM Ignition switch ON 11 to 14 V
B2-4 (IGP) - C92-81 (E1) Ignition switch signal Ignition switch ON 11 to 14 V
B2-6 (MREL) - C92-81 (E1) EFI MAIN NO.1 relay operation signal Ignition switch ON 11 to 14 V
B2-7 (STP) - C92-81 (E1) Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
B2-8 (ST1-) - C92-81 (E1) Stop light switch assembly signal (opposite of voltage at STP terminal) Ignition switch ON, brake pedal depressed Below 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
B2-10 (CANP) - C92-81 (E1) CAN communication line Ignition switch ON Pulse generation
(see waveform 2)
B2-11 (CANH) - C92-81 (E1) CAN communication line Ignition switch ON Pulse generation
(see waveform 2)
B2-14 (HAI1) - C92-81 (E1) Air pump heater for secondary air injection system Air pump heater operating Below 1.5 V
B2-16 (STA) - C92-81 (E1) ST NO. 1 relay operation signal Cranking 5.5 V or higher
B2-18 (CANN) - C92-81 (E1) CAN communication line Ignition switch ON Pulse generation
(see waveform 4)
B2-19 (CANL) - C92-81 (E1) CAN communication line Ignition switch ON Pulse generation
(see waveform 4)
B2-25 (AIR1) - C92-81 (E1) No. 2 emission control valve for secondary air injection system Ignition switch ON 11 to 14 V
B2-34 (IGR) - C92-81 (E1) Ignition signal Ignition switch ON 11 to 14 V
B2-41 (NEO) - C92-81 (E1) Engine speed signal sent to certification ECU (smart key ECU assembly) Idling with warm engine Pulse generation
(see waveform 3)
B2-44 (SPD) - C92-81 (E1) Vehicle speed signal from combination meter assembly Driving at 20 km/h (12 mph) Pulse generation
(see waveform 1)
B2-50 (FPC) - C92-81 (E1) Fuel pump control Engine stopped, ignition switch ON Below 1.5 V
B2-52 (EC) - Body ground Ground circuit of ECM Always Below 1 Ω
B2-53 (VPA) - B2-54 (EPA) Accelerator pedal position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 2.6 to 4.5 V
B2-55 (VCPA) - B2-54 (EPA) Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.5 V
B2-56 (VPA2) - B2-57 (EPA2) Accelerator pedal position sensor signal Ignition switch ON, accelerator pedal fully released 1.2 to 2.0 V
Ignition switch ON, accelerator pedal fully depressed 3.4 to 4.75 V
B2-58 (VCP2) - B2-57 (EPA2) Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.5 V
C92-2 (OE1+) - C92-1 (OE1-) Camshaft timing oil control valve assembly (for exhaust camshaft of bank 1) operation signal Idling Pulse generation
(see waveform 5)
C92-4 (OC2+) - C92-3 (OC2-) Camshaft timing oil control valve assembly (for intake camshaft of bank 2) operation signal Idling Pulse generation
(see waveform 5)
C92-6 (OC1+) - C92-5 (OC1-) Camshaft timing oil control valve assembly (for intake camshaft of bank 1) operation signal Idling Pulse generation
(see waveform 5)
C92-18 (ME01) - Body ground Ground circuit of ECM Always Below 1 Ω
C92-19 (M-) - C92-18 (ME01) Throttle actuator operation signal (negative terminal) Idling with warm engine Pulse generation
(see waveform 7)
C92-20 (M+) - C92-18 (ME01) Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(see waveform 8)
C92-21 (HT1B) - C92-23 (E04) Heated oxygen sensor (bank 1 sensor 2) heater operation signal Idling Below 3.0 V
Ignition switch ON 11 to 14 V
C92-22 (HA1A) - C92-23 (E04) Air fuel ratio sensor (bank 1 sensor 1) heater operation signal Idling with cold engine Pulse generation
(see waveform 6)
Ignition switch ON 11 to 14 V
C92-23 (E04) - Body ground Ground circuit of ECM Always Below 1 Ω
C92-24 (OE2+) - C92-47 (OE2-) Camshaft timing oil control valve assembly (for exhaust camshaft of bank 2) operation signal Idling Pulse generation
(see waveform 5)
C92-25 (LIN) - C92-81 (E1) LIN communication line Ignition switch ON Pulse generation
(see waveform 15)
C92-32 (IGT6) - C92-81 (E1) No. 6 ignition coil assembly (ignition signal) Idling with warm engine Pulse generation
(see waveform 14)
C92-33 (IGT5) - C92-81 (E1) No. 5 ignition coil assembly (ignition signal) Idling with warm engine Pulse generation
(see waveform 14)
C92-34 (IGT4) - C92-81 (E1) No. 4 ignition coil assembly (ignition signal) Idling with warm engine Pulse generation
(see waveform 14)
C92-35 (IGT3) - C92-81 (E1) No. 3 ignition coil assembly (ignition signal) Idling with warm engine Pulse generation
(see waveform 14)
C92-36 (IGT2) - C92-81 (E1) No. 2 ignition coil assembly (ignition signal) Idling with warm engine Pulse generation
(see waveform 14)
C92-37 (IGT1) - C92-81 (E1) No. 1 ignition coil assembly (ignition signal) Idling with warm engine Pulse generation
(see waveform 14)
C92-41 (E01) - Body ground Ground circuit of ECM Always Below 1 Ω
C92-42 (GE01) - C92-81 (E1) Shielded ground circuit of throttle actuator Always Below 1 Ω
C92-43 (E02) - Body ground Ground circuit of ECM Always Below 1 Ω
C92-44 (HT2B) - C92-46 (E05) Heated oxygen sensor (bank 2 sensor 2) heater operation signal Idling Below 3.0 V
Ignition switch ON 11 to 14 V
C92-45 (HA2A) - C92-46 (E05) Air fuel ratio sensor (bank 2 sensor 1) heater operation signal Idling with cold engine Pulse generation
(see waveform 6)
Ignition switch ON 11 to 14 V
C92-46 (E05) - Body ground Ground circuit of ECM Always Below 1 Ω
C92-48 (NSW) - C92-81 (E1) Park/Neutral position switch assembly signal Ignition switch ON and shift lever in P or N Below 1 V
Ignition switch ON and shift lever not in P or N 11 to 14 V
C92-52 (AIDI) - C92-81 (E1) Diagnostic information signal for secondary air injection system Secondary air injection system operating Pulse generation
(see waveform 16)
C92-54 (IGF1) - C92-81 (E1) Ignition coil assembly (ignition confirmation signal) Ignition switch ON 4.5 to 5.5 V
Idling with warm engine Pulse generation
(see waveform 14)
C92-61 (AIRV) - C92-81 (E1) Emission control valve signal for secondary air injection system Ignition switch ON 11 to 14 V
C92-63 (AIRP) - C92-81 (E1) Air pump control Ignition switch ON 11 to 14 V
C92-66 (NE+) - C92-65 (NE-) Crankshaft position sensor signal Idling with warm engine Pulse generation
(see waveform 11)
C92-68 (VG) - C92-70 (E2G) Mass air flow meter sub-assembly signal Idling, shift lever in P or N, A/C switch off 0.5 to 3.0 V
C92-71 (THA) - C92-74 (EAIP) Intake air temperature sensor signal Idling, intake air temperature 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
C92-72 (AIP2) - C92-74 (EAIP) Secondary air injection system pressure signal Ignition switch ON 0.5 to 4.5 V
C92-73 (AIP) - C92-74 (EAIP) Secondary air injection system pressure signal Ignition switch ON 0.5 to 4.5 V
C92-75 (VCAI) - C92-81 (E1) Power source for sensors (specific voltage) Ignition switch ON 4.5 to 5.5 V
C92-76 (PSP) - C92-123 (ETHW) Power steering oil pressure sensor signal Ignition switch ON 0.5 to 4.5 V
C92-81 (E1) - Body ground Ground circuit of ECM Always Below 1 Ω
C92-82 (PRG) - C92-81 (E1) Purge VSV operation signal Ignition switch ON 11 to 14 V
Idling with warm engine, under purge control Pulse generation
(see waveform 9)
C92-84 (#50) - C92-41 (E01) No. 5 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(see waveform 10)
C92-85 (#30) - C92-41 (E01) No. 3 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(see waveform 10)
C92-86 (#10) - C92-41 (E01) No. 1 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(see waveform 10)
C92-87 (VCV1) - C92-81 (E1) Power source for sensors (specific voltage) Ignition switch ON 4.5 to 5.5 V
C92-89 (VV1+) - C92-88 (VV1-) VVT sensor (for intake camshaft of bank 1) signal Idling with warm engine Pulse generation
(see waveform 11)
C92-90 (EV1+) - C92-88 (VV1-) VVT sensor (for exhaust camshaft of bank 1) signal Idling with warm engine Pulse generation
(see waveform 17)
C92-94 (KNK1) - C92-93 (EKNK) Knock control sensor (bank 1) signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(see waveform 12)
C92-96 (OX1B) - C92-95 (EX1B) Heated oxygen sensor (bank 1 sensor 2) signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(see waveform 13)
C92-97 (A1A-) - C92-81 (E1) Air fuel ratio sensor (bank 1 sensor 1) signal Ignition switch ON 2.9 V*
C92-98 (A1A+) - C92-81 (E1) Air fuel ratio sensor (bank 1 sensor 1) signal Ignition switch ON 3.3 V*
C92-101 (VTA2) - C92-124 (ETA) Throttle position sensor signal (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 2.1 to 3.1 V
Ignition switch ON, accelerator pedal fully depressed 4.6 to 5.0 V
C92-104 (+BM) - C92-81 (E1) Power source of throttle actuator Always 11 to 14 V
C92-107 (#60) - C92-41 (E01) No. 6 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(see waveform 10)
C92-108 (#40) - C92-41 (E01) No. 4 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(see waveform 10)
C92-109 (#20) - C92-41 (E01) No. 2 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(see waveform 10)
C92-110 (VCV2) - C92-81 (E1) Power source for sensors (specific voltage) Ignition switch ON 4.5 to 5.5 V
C92-112 (VV2+) - C92-111 (VV2-) VVT sensor (for intake camshaft of bank 2) signal Idling with warm engine Pulse generation
(see waveform 11)
C92-113 (EV2+) - C92-111 (VV2-) VVT sensor (for exhaust camshaft of bank 2) signal Idling with warm engine Pulse generation
(see waveform 17)
C92-117 (KNK2) - C92-116 (EKN2) Knock control sensor (bank 2) signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(see waveform 12)
C92-119 (OX2B) - C92-118 (EX2B) Heated oxygen sensor (bank 2 sensor 2) signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(see waveform 13)
C92-120 (A2A-) - C92-81 (E1) Air fuel ratio sensor (bank 2 sensor 1) signal Ignition switch ON 2.9 V*
C92-121 (A2A+) - C92-81 (E1) Air fuel ratio sensor (bank 2 sensor 1) signal Ignition switch ON 3.3 V*
C92-122 (THW) - C92-123 (ETHW) Engine coolant temperature sensor signal Idling, engine coolant temperature 60 to 120°C (140 to 248°F) 0.2 to 1.0 V
C92-125 (VCTA) - C92-124 (ETA) Power source for throttle position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
C92-126 (VTA1) - C92-124 (ETA) Throttle position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 3.2 to 4.8 V

*: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

WAVEFORM 1


A292384E12
2.813,1.25 3.271,1.448 0.458,0.198 10 false GND

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 2


A292386E27
3,1.406 3.365,1.583 0.365,0.177 10 false GND

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Between CANP and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 3


A210050E20
2.833,2.385 3.167,2.542 0.333,0.156 10 false GND

Engine Speed Signal
ECM Terminal Name Between NEO and E1
Tester Range 5 V/DIV., 2 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 4


A292387E30
3,1.375 3.344,1.573 0.344,0.198 10 false GND

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Between CANN and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 5


A292381E15
0.615,1.125 1.073,1.323 0.458,0.198 10 false GND

Camshaft Timing Oil Control Valve Assembly Operation Signal
ECM Terminal Name Between OC1+ and OC1-
Between OC2+ and OC2-
Between OE1+ and OE1-
Between OE2+ and OE2-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 6


A205412E49
2.698,0.844 3.063,1.01 0.365,0.167 10 false GND

Air Fuel Ratio Sensor (Sensor 1) Heater Operation Signal
ECM Terminal Name Between HA1A and E04
Between HA2A and E05
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with cold engine


WAVEFORM 7


A245848E83
2.854,0.99 3.188,1.135 0.333,0.146 10 false GND 0.479,0.625 0.667,0.771 0.188,0.146 10 false M-

Throttle Actuator Negative Terminal Signal
ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 8


A208000E88
2.854,0.969 3.188,1.115 0.333,0.146 10 false GND 0.5,0.615 0.719,0.76 0.219,0.146 10 false M+

Throttle Actuator Positive Terminal Signal
ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 9


A218020E45
2.802,0.927 3.135,1.063 0.333,0.135 10 false GND

Purge VSV Operation Signal
ECM Terminal Name Between PRG and E1
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling with warm engine, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 10


A292383E07
0.667,1.583 1.125,1.781 0.458,0.198 10 false GND

No. 1 (to No. 6) Fuel Injector Assembly Signal
ECM Terminal Name Between #10 (to #60) and E01
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 11


A207436E15
0.292,1.229 0.521,1.385 0.229,0.156 10 false NE 2.99,1.229 3.323,1.385 0.333,0.156 10 false GND 2.99,1.781 3.323,1.938 0.333,0.156 10 false GND 2.99,2.167 3.323,2.323 0.333,0.156 10 false GND 0.208,1.74 0.51,1.896 0.302,0.156 10 false VV1 0.208,2.031 0.51,2.188 0.302,0.156 10 false VV2

Crankshaft Position Sensor Signal and VVT Sensor (for Intake Camshaft) Signal
ECM Terminal Name Between NE+ and NE-
Between VV1+ and VV1-
Between VV2+ and VV2-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 12


A283572E41
2.615,1 3.115,1.292 0.5,0.292 10 false GND

Knock Control Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Between KNK2 and EKN2
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle condition.




WAVEFORM 13


A292382E08
0.615,1.469 1.073,1.667 0.458,0.198 10 false GND

Heated Oxygen Sensor (Sensor 2) Signal
ECM Terminal Name Between OX1B and EX1B
Between OX2B and EX2B
Tester Range 0.2 V/DIV., 200 ms./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:

In the Data List, item O2S B1S2 and O2S B2S2 shows the ECM values from the heated oxygen sensor.



WAVEFORM 14


A210049E20
2.875,1.667 3.208,1.813 0.333,0.146 10 false GND 2.875,2.542 3.208,2.698 0.333,0.156 10 false GND 0.156,1.156 0.427,1.365 0.271,0.208 10 false IGT 0.156,2.01 0.635,2.208 0.479,0.198 10 false IGF1

Ignition Coil Assembly Signal (IGT and IGF1 Signal)
ECM Terminal Name Between IGT (1 to 6) and E1
Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 15


A349005E05
2.927,1.906 3.281,2.115 0.354,0.208 10 false GND

LIN Communication Signal (Reference)
ECM Terminal Name Between LIN and E1
Tester Range 2 V/DIV., 10 ms./DIV.
Condition Idling with warm engine


WAVEFORM 16


A255990E07
2.958,1 3.292,1.146 0.333,0.146 10 false GND

Terminal AID of Air Injection Control Driver
ECM Terminal Name Between AIDI and E1
Tester Range 5 V/DIV., 50 msec./DIV.
Condition Performing Active Test using GTS (Secondary Air Injection Check)

HINT:

The wavelength changes when the air injection control driver detects malfunctions in the secondary air injection system.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P161311



WAVEFORM 17


A356009E14
2.813,1.458 3.271,1.656 0.458,0.198 10 false GND 2.813,2.198 3.271,2.396 0.458,0.198 10 false GND 0.167,1.365 0.625,1.563 0.458,0.198 10 false CH1 0.156,2.135 0.615,2.333 0.458,0.198 10 false CH2

VVT Sensor (for Exhaust Camshaft) Signal
ECM Terminal Name CH1: Between EV1+ and VV1-
CH1: Between EV2+ and VV2-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.