Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P011011  Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Ground  P011015  Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Battery or Open  


DESCRIPTION

A283580E01
3.354,2.271 3.74,1.99 false 2.26,0.406 2.833,0.667 0.573,0.26 10 Fig. 1: 3.292,4.271 4.167,4.5 0.875,0.229 10 Temperature 2.396,0.969 2.771,1.219 0.375,0.25 10 (kΩ) 2.281,1.146 2.521,1.365 0.24,0.219 10 30 2.281,1.583 2.521,1.802 0.24,0.219 10 10 2.354,1.875 2.594,2.094 0.24,0.219 10 5 2.354,2.094 2.594,2.313 0.24,0.219 10 3 2.354,2.26 2.51,2.479 0.156,0.219 10 2 2.344,2.531 2.594,2.75 0.25,0.219 10 1 2.24,2.833 2.479,3.052 0.24,0.219 10 0.5 2.24,3.198 2.479,3.417 0.24,0.219 10 0.2 2.24,3.469 2.479,3.688 0.24,0.219 10 0.1 2.281,1.323 2.531,1.542 0.25,0.219 10 20 2.542,3.823 2.781,4.042 0.24,0.219 10 -20 2.938,3.823 3.177,4.042 0.24,0.219 10 0 3.208,3.823 3.448,4.042 0.24,0.219 10 20 3.521,3.823 3.76,4.042 0.24,0.219 10 40 3.833,3.823 4.073,4.042 0.24,0.219 10 60 4.146,3.823 4.385,4.042 0.24,0.219 10 80 4.385,3.823 4.625,4.042 0.24,0.219 10 100 2.583,4 2.823,4.219 0.24,0.219 10 -4 2.896,4 3.135,4.219 0.24,0.219 10 32 3.208,4 3.448,4.219 0.24,0.219 10 68 3.479,4 3.729,4.25 0.25,0.25 10 104 3.792,4 4.125,4.25 0.333,0.25 10 140 4.094,4 4.417,4.25 0.323,0.25 10 176 4.385,4 4.708,4.25 0.323,0.25 10 212 4.677,3.823 5,4.073 0.323,0.25 10 (°C) 4.677,4 5,4.25 0.323,0.25 10 (°F) 3.802,1.896 4.583,2.167 0.781,0.271 10 Acceptable 2.26,0.719 3.083,0.917 0.823,0.198 10 Resistance 2.24,3.021 2.479,3.24 0.24,0.219 10 0.3

The intake air temperature sensor, mounted on the mass air flow meter, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).

The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, according to changes in the intake air temperature, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

HINT:

When DTC P011011 or P011015 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P011011 Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Ground A short in the intake air temperature sensor circuit for 0.5 seconds or more (1 trip detection logic).
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (mass air flow meter)

·

ECM


Comes on SAE: P0112
P011015 Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Battery or Open An open in the intake air temperature sensor circuit for 0.5 seconds or more (1 trip detection logic).
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (mass air flow meter)

·

ECM


Comes on SAE: P0113

HINT:

When any of these DTCs are output, check the intake air temperature using the GTS. Enter the following menus: Powertrain / Engine / Data List / All Data / Intake Air Temperature.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit


MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor circuit and stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 0.5 seconds or more.

7.

Enter the following menus: Powertrain / Engine / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: P011011 or P011015.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A426323E13
0.229,2.594 1.958,2.99 1.729,0.396 10 false C71 0.219,2.76 4.531,3.031 4.313,0.271 10 false Intake Air Temperature Sensor (Mass Air Flow Meter) 5.719,3.156 6.427,3.542 0.708,0.385 10 false ECM 5.25,1.333 5.719,1.594 0.469,0.26 10 false THA 4.938,1.333 5.271,1.667 0.333,0.333 10 false 71 4.948,1.927 5.281,2.26 0.333,0.333 10 false 74 5.25,1.927 5.719,2.188 0.469,0.26 10 false EAIP 5.885,0.948 6.219,1.281 0.333,0.333 10 false 5 V 5.833,1.219 6.167,1.552 0.333,0.333 10 false R 2.208,1.333 2.542,1.667 0.333,0.333 10 false 1 2.198,1.927 2.531,2.26 0.333,0.333 10 false 2 5.719,2.979 6.052,3.25 0.333,0.271 10 false C92 1.885,1.927 2.375,2.167 0.49,0.24 10 false E2 1.781,1.344 2.271,1.583 0.49,0.24 10 false THA

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
a.

Turn the ignition switch to ON.


b.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature
50003 372 214
OK:

Same as actual intake air temperature.


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) B
Same as actual intake air temperature C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F).





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A413578C05
0.167,2.427 0.583,2.729 0.417,0.302 0.646,0.167 0.958,0.365 0.313,0.198 10 false *1 2.563,0.094 2.875,0.292 0.313,0.198 10 false *2 2.396,0.833 2.854,1.031 0.458,0.198 10 false THA 2.385,1.333 3,1.531 0.615,0.198 10 false EAIP 0.26,2 0.573,2.198 0.313,0.198 10 false *a 0.24,2.479 0.698,2.677 0.458,0.198 10 false C71
*1 Mass Air Flow Meter
*2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter)


Disconnect the mass air flow meter connector.


b.

Connect terminals 1 (THA) and 2 (E2) of the mass air flow meter connector on the wire harness side.


c.

Turn the ignition switch to ON.


d.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature
50003 372 214
Standard value:

140°C (284°F)


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
A410578C16
2.219,0.813 2.729,1.052 0.51,0.24 10 false THA 0.948,0.823 1.458,1.063 0.51,0.24 10 false THA 1.042,1.198 1.552,1.438 0.51,0.24 10 false E2 2.219,1.198 2.729,1.438 0.51,0.24 10 false EAIP 0.563,0.281 1.073,0.521 0.51,0.24 10 false *1 2.563,0.292 3.073,0.531 0.51,0.24 10 false *2
*1 Mass Air Flow Meter
*2 ECM


a.

Disconnect the mass air flow meter connector.


b.

Turn the ignition switch to ON.


c.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature
50003 372 214
Standard value:

-40°C (-40°F)


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR