Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P011511  Engine Coolant Temperature Sensor 1 Circuit Short to Ground  P011515  Engine Coolant Temperature Sensor 1 Circuit Short to Battery or Open  


DESCRIPTION

A thermistor, whose resistance value varies according to the engine coolant temperature, is built into the engine coolant temperature sensor. The structure of the sensor and its connection to the ECM are the same as those of the intake air temperature sensor.

HINT:

When DTC P011511 or P011515 is stored, the ECM enters fail-safe mode. During fail-safe mode, the engine coolant temperature is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P011511 Engine Coolant Temperature Sensor 1 Circuit Short to Ground A short in the engine coolant temperature sensor circuit for 0.5 seconds or more (1 trip detection logic).
·

Short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on SAE: P0117
P011515 Engine Coolant Temperature Sensor 1 Circuit Short to Battery or Open An open or short in the engine coolant temperature sensor circuit for 0.5 seconds or more (1 trip detection logic).
·

Short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on SAE: P0118

HINT:

When any of these DTCs are output, check the engine coolant temperature using the GTS. Enter the following menus: Powertrain / Engine / Data List / All Data / Coolant Temperature.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit


MONITOR DESCRIPTION

The engine coolant temperature sensor is used to monitor the engine coolant temperature. The engine coolant temperature sensor has a thermistor with a resistance that varies according to the temperature of the engine coolant. When the engine coolant temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are reflected in the output voltage from the sensor. The ECM monitors the sensor voltage and uses this value to calculate the engine coolant temperature. If the sensor output voltage deviates from the normal operating range, the ECM interprets this as a fault in the engine coolant temperature sensor circuit and stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 0.5 seconds or more.

7.

Enter the following menus: Powertrain / Engine / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: P011511 or P011515.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A229557E32
0.542,1.875 1.031,2.115 0.49,0.24 10 false C84 5.594,2.125 6.01,2.427 0.417,0.302 10 false ECM 5.583,1.938 5.906,2.125 0.323,0.188 10 false C92 2.563,1.188 2.781,1.375 0.219,0.188 10 false 1 2.573,0.573 2.854,0.781 0.281,0.208 10 false 2 4.802,1.135 5.156,1.302 0.354,0.167 10 false 123 4.823,0.531 5.271,0.688 0.448,0.156 10 false 122 5.167,1.167 5.74,1.333 0.573,0.167 10 false ETHW 5.167,0.583 5.542,0.75 0.375,0.167 10 false THW 0.531,2.031 2.969,2.281 2.438,0.25 10 false Engine Coolant Temperature Sensor 5.813,0.24 6.125,0.427 0.313,0.188 10 false 5 V 5.76,0.469 6.063,0.677 0.302,0.208 10 false R

CAUTION / NOTICE / HINT

HINT:
·

If DTC P011511 is stored, check that the engine does not overheat (the DTC P011511 may be stored due to engine overheating).

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Start the engine and warm it up.


b.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
Standard value:

Between 75 and 100°C (167 and 212°F) with warm engine.


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) B
Between 75 and 100°C (167 and 212°F) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F).





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the engine coolant temperature sensor connector.

A375112C03
6.083,1.5 6.5,1.75 0.417,0.25 2.771,1.833 3.083,2.031 0.313,0.198 10 false *2 1.25,1.75 1.563,1.948 0.313,0.198 10 false *1 2.135,1.552 2.75,1.75 0.615,0.198 10 false ETHW 2.219,1 2.833,1.198 0.615,0.198 10 false THW 5.333,0.5 5.646,0.698 0.313,0.198 10 false *a 6.167,1.552 6.781,1.75 0.615,0.198 10 false C84
*1 Engine Coolant Temperature Sensor *2 ECM
*a Front view of wire harness connector
(to Engine Coolant Temperature Sensor)
- -



b.

Connect terminals 1 and 2 of the engine coolant temperature sensor connector on the wire harness side.


c.

Turn the ignition switch to ON.


d.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
Standard value:

140°C (284°F)


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
A255925C23
0.667,0.156 0.823,0.313 0.156,0.156 10 false *1 2.573,0.156 2.729,0.313 0.156,0.156 10 false *2 2.229,1.031 2.573,1.188 0.344,0.156 10 false THW 2.219,1.396 2.646,1.552 0.427,0.156 10 false ETHW
*1 Engine Coolant Temperature Sensor
*2 ECM


a.

Disconnect the engine coolant temperature sensor connector.


b.

Turn the ignition switch to ON.


c.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
Standard value:

-40°C (-40°F)


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR